Sony DPP-FP70 Service Manual ▷ View online
4-5
DPP-FP70
4-2-4. SETTING OF DESTINATION
1.
While pressing the [ENTER] and [CANCEL] buttons
simultaneously, press the [ON/STANDBY| button. (Service
mode starts.)
simultaneously, press the [ON/STANDBY| button. (Service
mode starts.)
2.
Release all buttons when the initial screen of the service mode
is displayed on the LCD display.
is displayed on the LCD display.
3.
Press the [
r
] key several times to move the cursor to [Select
Model], and press [ENTER].
4.
Move the cursor to the desired destination by using [
R
], [
r
],
[
T
], [
t
], and press [ENTER].
5.
Press the [
R
] key several times to return to the initial screen
(on which “DPP-FP70 (XX)” is displayed) of the service mode
to confirm that the destination is changed.
to confirm that the destination is changed.
6.
Turn off the power and disconnect the power cord from the
receptacle.
receptacle.
4) For the procedure of the destination change, refer to the next
paragraph [4-2-4. Setting of destination] shown below.
4-3-1. FAN OPERATION CHECK
Operation of fan can be check as follows:
Procedure:
1.
Start the service mode. (Refer to Section 4-1-1.)
2.
Press the [PRINT] button on the service mode startup screen.
3.
Check that the fan rotating sound changes in the following order
starting from
starting from
Low speed
t High speed t Stop by every
pressing of the [PRINT] button.
4.
Quit the service mode. (Refer to Section 4-1-1.)
4-3. CHECK
4-3-2. BUTTON/LED/TRAY SENSOR/RIBBON
SENSOR OPERATION CHECK
The operation of each button, LED and sensors can be checked.
Note:
After the machine enters this mode once, it cannot exit this mode
until the “Button operation check” is completed.
Procedure:
1.
Start the service mode. (Refer to Section 4-1-1.)
2.
Select “Button Test” using the arrow buttons (f,F) and press
the [ENTER] button.
The following screen is displayed.
the [ENTER] button.
The following screen is displayed.
Button operation check
Press the button on the operation panel of this unit. The pressed
button indication on the LCD of main unit lights in yellow. The
following screen shows that the [MENU] button is pressed.
button indication on the LCD of main unit lights in yellow. The
following screen shows that the [MENU] button is pressed.
When all 10 buttons are pressed one button after another, all button
indications on the screen light in red.
indications on the screen light in red.
4-6
DPP-FP70
When the checks of all buttons are completed without problem, the
initial screen of the service mode is displayed and “OK” is displayed
to the right of “Button Test”.
initial screen of the service mode is displayed and “OK” is displayed
to the right of “Button Test”.
3.
Quit the service mode. (Refer to Section 4-1-1.)
LED operation check
Check that the “PRINT LED” and the “Access LED” light up during
the “Button Test”, and then flash before turning off when the “Button
Test” is completed.
the “Button Test”, and then flash before turning off when the “Button
Test” is completed.
Ribbon sensor operation check
Whether the ribbons are correctly recognized or not can be checked.
Check to see that the ribbon type display on the screen agrees with
the inserted ribbon when different types of ribbon are inserted.
Check to see that the ribbon type display on the screen agrees with
the inserted ribbon when different types of ribbon are inserted.
Print Pack Size
Display
Postcard size
Post
L size
L
Not installed
None
Tray sensor operation check
Whether the trays are correctly recognized or not can be checked.
Check to see that the tray type displayed on the screen agrees with
the inserted tray when different types of tray are inserted.
Check to see that the tray type displayed on the screen agrees with
the inserted tray when different types of tray are inserted.
Print Pack Size
Display
Postcard size
Post
L size
L
Not installed
None
4-3-3. IMAGE READING CHECK FROM MEMORY
CARD
Image reading from Memory Stick or Memory Stick Duo, SD card
or mini SD card and CF card can be checked. (If it is JPG, the
image is arbitrary.)
or mini SD card and CF card can be checked. (If it is JPG, the
image is arbitrary.)
Preparation:
Place the JPEG file in the root directory of a Memory Stick.
(Filename: MS.jpg)
Place the JPEG file in the root directory of an SD card. (Filename:
SD.jpg) (Use the LOCK OFFed card.)
Place the JPEG file in the root directory of a CF card. (Filename:
CF.jpg)
(Filename: MS.jpg)
Place the JPEG file in the root directory of an SD card. (Filename:
SD.jpg) (Use the LOCK OFFed card.)
Place the JPEG file in the root directory of a CF card. (Filename:
CF.jpg)
Procedure:
1.
Start the service mode. (Refer to Section 4-1-1.)
2.
Select “Card Test” by using the arrow buttons (f, F).
3.
Insert a Memory Stick that is prepared separately, and press
the [G] button.
the [G] button.
4.
Confirm that the MS.jpg image is displayed.
5.
Remove the Memory Stick, and insert an SD card that is
prepared separately.
prepared separately.
6.
Press the [F] button and confirm that the SD.jpg image is
displayed.
displayed.
7.
Remove the SD card, and insert a CF card that is prepared
separately.
separately.
8.
Press the [F] button and confirm that the CF.jpg image is
displayed.
displayed.
Even if the button is not pushed, it is judged that the card is inserted.
Insert all of the one card, and confirm it.
Insert all of the one card, and confirm it.
4-7
DPP-FP70
4-3-4. USB HOST/DEVICE COMMUNICATION
CHECK
The digital camera for PictBridge or the digital camera , the USB
memory and the photo storage for the mass storage are connected
with the terminal PictBridge/EXT INTERFACE of this machine,
and confirm that this machine reacts.
This machine connects with Windows PC that installs software by
USB cable, and confirm that Windows PC reacts.
memory and the photo storage for the mass storage are connected
with the terminal PictBridge/EXT INTERFACE of this machine,
and confirm that this machine reacts.
This machine connects with Windows PC that installs software by
USB cable, and confirm that Windows PC reacts.
9.
When all memory cards reading are completed, press the
[ENTER] button.
[ENTER] button.
• When all memory cards work normally so that images can
be read without error, the character OK is displayed on the
right of “Card Test” on the service mode startup screen.
right of “Card Test” on the service mode startup screen.
• If a memory card is not set, or if image is not contained in a
memory card, or image cannot be read from a memory
card, background of the screen becomes red and the character
NG (No Good) is displayed in the left bottom of a screen.
card, background of the screen becomes red and the character
NG (No Good) is displayed in the left bottom of a screen.
• If either a memory card is NG (No Good), the character
NG (No Good) is displayed on the right of “Card Test” on
the service mode startup screen.
the service mode startup screen.
10. Quit the service mode. (Refer to Section 4-1-1.)
4-8
DPP-FP70
4-3-5. ABOUT THE ERROR INDICATION
In this unit, “printer status” and “last 10 error status” can be indicated
and checked in the service mode.
and checked in the service mode.
Startup procedure
1.
Start the service mode. (Refer to Section 4-1-1.)
2.
Select “Print Status” using the arrow buttons (f,F) and press
the [ENTER] button.
“Status indication” screen is displayed. The 1/2 page and the
2/2 page are displayed by using the arrow buttons (f, F).
the [ENTER] button.
“Status indication” screen is displayed. The 1/2 page and the
2/2 page are displayed by using the arrow buttons (f, F).
**Error 0** is displayed on the initial status screen in the past error
status. To display the earlier error history, press the arrow button
(G) and to display the later error history, press the arrow button
(g). The pages can be selected by using the arrow buttons (f, F).
status. To display the earlier error history, press the arrow button
(G) and to display the later error history, press the arrow button
(g). The pages can be selected by using the arrow buttons (f, F).
When the arrow button (g) is pressed in the **Error 0** state, **Last
Status** is displayed. In the case that no error occurred in the past,
**Last Status** is displayed on the initial status screen. Use the
arrow button (g) to display **Current Status**.
Status** is displayed. In the case that no error occurred in the past,
**Last Status** is displayed on the initial status screen. Use the
arrow button (g) to display **Current Status**.
Ribbon:
Ribbon type
None:
Ribbon is not installed.
Post:
Cartridge for postcard size is inserted.
L:
Cartridge for L size is inserted.
Cleaning:
Cartridge for cleaning is inserted.
Unknown:
Unknown
Tray:
Tray type
Post:
Tray for postcard size is inserted.
L:
Tray for L size is inserted.
None;
Tray is not installed.
3.
After confirming the error indication, quit the service mode.
(Refer to Section 4-1-1.)
(Refer to Section 4-1-1.)
Description of screen
Indication in red:
Status indication
**Last Status**:
Status of last printing
**Current Status**:
Current status
**Error 0**:
Status when the last error occurred
**Error 1**:
Status of error occurred two times
earlier The last ten errors are stored.
earlier The last ten errors are stored.
**Error 9**:
Status of error occurred ten times
earlier
earlier
Card:
King of memory card when making an error
Error:
Error type
No Error:
No error
No Ribbon:
No ribbon
Ribbon End:
Ribbon end
Ribbon Error:
Ribbon error
Paper End:
No paper
Paper Long:
Paper length error (long)
Paper Short:
Paper length error (short)
Paper Exist:
Paper exists
PE Error:
PE sensor error
Head Error:
Head error
MMotor Error:
DC motor error
SMotor Error:
Stepping motor error
Mode Error:
Mode transition error
HeatStrage Error:
Heat storage correction error
Other Error:
Other error
Unknown:
Unknown
MD Status:
Not used
Pass:
Print pass
Feed:
During paper feeding
Y:
During yellow printing
M:
During magenta printing
C:
During cyan printing
Lami:
During laminated paper printing
Unknown:
Unknown
Total Try:
Total count of tried printing
Total Print:
Total count of printing
HEAD A/D:
Thermistor A/D value of head
SupStep:
Count of paper feed step
Progress:
Progress (%) of each color (Y, M, C, L)
during printing
during printing
Sensor:
Each sensor value (1 or 0)
R2
R1
R0
RM
T1
T0
PE
CF_VS
R2
R1
R0
RM
T1
T0
PE
CF_VS
Cool down:
Cool down (Decrease the heat temperature)
Paper Sup:
Paper feed
Paper Rev1:
Paper reverse 1
(Reverse paper to the point of PE paper feed
by determining the paper length.)
(Reverse paper to the point of PE paper feed
by determining the paper length.)
Paper Rev2:
Paper reverse 2
(Reverse paper after single color printing)
(Reverse paper after single color printing)
Paper Init0:
Paper initial point 0
Paper Init1:
Paper initial point 1
Print:
Printing
Paper Eject1:
Paper eject 1
(Paper eject at the completion of printing)
(Paper eject at the completion of printing)
Paper Error Eject0:
Error paper eject 0
Paper Error Eject1:
Error paper eject 1
Timeout M0/1:
Return to M0 or M1
Unknown:
Unknown
Mode Pos:
Head position
PR
RS
PF
PU
RL
PR
RS
PF
PU
RL
Unknown:
Unknown
Click on the first or last page to see other DPP-FP70 service manuals if exist.