DOWNLOAD Sony HDR-UX3E / HDR-UX5 / HDR-UX5E / HDR-UX7 / HDR-UX7E (serv.man3) Service Manual ↓ Size: 1.42 MB | Pages: 67 in PDF or view online for FREE

6-38

HDR-UX3E/UX5/UX5E/UX7/UX7E_ADJ

1) Before setting the optical sensor disc, remove a lug on the sensor

side of the disc.

2) Push in the optical sensor disc until it clicks same as when a

disc is set, and adjust the position so that the cable from the
sensor comes just above the pickup lens, as shown below.
After positioning, fix the disc with a tape so that it does not
rotate.

Remove this lug

The adjustment data for the drive block are recorded to the IC4302
on the MD-134 board.
These data cannot be read or written from the adjustment remote
commander or SeusCam, unlike the camera and LCD adjustment
data.
Accordingly, be sure to adjust all items of the drive adjustment
when the following parts were replaced:
• Drive block

• Mounted MD-134 board

• IC4101 (RF process) on the MD-134 board

• IC4201 (DVD DSP) on the MD-134 board

• IC4401 (DVD mecha drive) on the MD-134 board

Adjust the drive block in the following order:
1) POWER Adjustment
2) SERVO Adjustment

In the POWER Adjustment, operate the drive with the disc cover
left open. During the adjustment, be sure to observe the fol-
lowing precautions:
1) Set the optical sensor disc correctly.
2) Keep  the distance of more than 30 cm apart from the

camcoder.

3) Work on the LCD screen side of the camcoder (opposite

side of the drive).

Laser light of the equipment is focused by the object lens
in the optical pick-up so that the light focuses on the reflec-
tion surface of the disc.
Therefore, be sure to keep your eyes more then 30 cm apart
from the object lens when you check the emission of laser
diode.

This part should come just above the pickup

Fix with a tape

Pickup Lens (Laser Diode)

6-39

HDR-UX3E/UX5/UX5E/UX7/UX7E_ADJ

Name

DVD-R Disc
for Self Jitter

DVD-RW
Reference + DOW
Disc

DVD+RDL
Self Disc

Use

Diagnosis and adjustment of DVD-R

Diagnosis and adjustment of DVD-RW

Diagnosis and adjustment of DVD+RDL

Remark

This disc can be used about 78 times (min. 22 times) for the
diagnosis and adjustment. (Note 3)

This disc can be used about 1174 times for the diagnosis and
adjustment. (Note 3)

This disc can be used about 38 times (min. 9 times) for the
diagnosis and adjustment. (Note 3)

If the use counts of the DVD-R Disc for Self Jitter, DVD-RW Reference + DOW Disc, or DVD+RDL Disc for Self Jitter exceed
respective limits, the following message will be displayed. Replace it with a new disc and click the [OK] button in the message
window.
The disc use counts are saved in the PC. Accordingly, the disc used for diagnosis and adjustment, PC and drive adjustment
program (AUDIT for 2007) must always be controlled in the same combination.
If the disc is used with another PC or other versions (AUDIT for Service, AUDIT for UX1, etc.), the diagnosis and adjustment
will fail and that disc will no longer be able to use.

To diagnose and adjust the drive block, the discs listed in the following table are used.

Use the specified disc that matches each diagnostic and adjustment item. (A message is displayed by the AUDIT)
If a wrong disc is used, the disc could be destroyed and could not be reused.

Handle the disc with care, and before use, check if the disc is scratched or dirty.

注3：DVD-R セルフジッターディスク，DVD-RWリファレンス+ DOWディスクとDVD+RDLセルフジッターディスクは，

使用限度を超えると次のメッセージが表示されます。新しいディスクと交換して，メッセージの[OK]ボタンをクリッ

クしてください。 

ディスクの使用回数は，PC内部に保存されます。このため，診断・調整で使用するディスクとPCおよびドライブ

調整プログラム（AUDIT for 2007）は，常に同一の組み合わせになるように管理してください。 

別のPCや他のバージョン（AUDIT for Service，AUDIT for UX1等）でディスクを使用すると，診断・調整が正常に

行われずNGとなってしまい，そのディスクが使用不可能になってしまう場合があります。 

6-40

HDR-UX3E/UX5/UX5E/UX7/UX7E_ADJ

Extract the compressed file in the ZIP format. If the extracted file (AUDIT for 2007.msi) is executed, the installer will start. Perform the
installation following the instructions given on the screen of the installer.

Click the [Start] button on the task bar, and from the [Programs], click [AUDIT for Service] – [AUDIT for 2007], and the AUDIT will start. The
SeusEX starts simultaneously with the start of AUDIT, and the operation screen appears only for a moment.
Again, the SeusEX starts and the operation screen is displayed, and after it is minimized for display at the lower left of the desktop, the
AUDIT operation screen appears. If the SeusEX cannot start (because, for instance, the HASP key is not connected to the PC), the AUDIT
also does not start.

1. Diagnosis section

2. Adjustment section

3. Comment display section

4. Status display section

6. 

[SET]

 button

7. Menu section

5. 

[STOP]

 button

1.XX

8. Caution display 

section

6-41

HDR-UX3E/UX5/UX5E/UX7/UX7E_ADJ

Use these buttons when diagnosing the drive block.

Use these buttons when adjusting the drive block.

At the execution of diagnosis and adjustment, its progress situa-
tion is displayed.
1) [Clear] button

This button clears the comment in the display section.

2) [LOG] button

This button saves the comment in the display section as a log
file.

The result of diagnosis and adjustment is displayed.

[STOP]

This button stops the diagnosis and adjustment in the midway.

[SET]

This button cancels the TEST mode set to the cam coder during
the diagnosis and adjustment. If the TEST mode is cancelled suc-
cessfully, the following message is displayed.

Before exiting the AUDIT, be sure to cancel the TEST mode
by clicking the SET button of “After completing the TEST”.
Unless the TEST mode is cancelled, the drive may not op-
erate normally, such that “disc cover does not open”, “drive
error is displayed”, etc..

1) [RESET] button

This button resets internal register.
(Use this button to interrupt the work so far when diagnosis
and adjustment stopped and no response is returned. The work
terminates with the previous adjustment data written to the
camcoder.)

2) [Lid Open] button

This button opens the disc cover.

At the execution of POWER Adjustment, the caution of POWER
Adjustment is displayed.

[Clear]

 button

[LOG]

 button