DOWNLOAD Sony HDR-UX3E / HDR-UX5 / HDR-UX5E / HDR-UX7 / HDR-UX7E (serv.man3) Service Manual ↓ Size: 1.42 MB | Pages: 67 in PDF or view online for FREE

6-26

HDR-UX3E/UX5/UX5E/UX7/UX7E_ADJ

Before performing the defect adjustment, make sure that
the lens temperature of the camcorder exceeds 39 ºC.

[Preparation (Temperature Check)]
1) Click the [Preparation] button of the CAMERA Adjustment 5

to display the Preparation screen.

2) Click the [Temperature Check] button of the Preparation screen,

the following screen will appear.

[Checking method]
Click the [Start]  button of the Temperature Check, and the
camcorder will go in the Temperature Check mode and the tem-
perature check result will be displayed on the LCD screen. Per-
form the aging if the check result is NG (below 39 ºC). To exit the
Temperature Check mode, click the [Stop] button.

[Aging method]
Set the camcorder to the Movie mode, and place the LCD screen
in the “reverse-closed” state. (In this state, the temperature rises
more quickly than that in other states.)
Set the camcorder to the Temperature Check mode, and wait until
the LCD screen display changes from NG (grid pattern) to OK
(color bars).

[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Camera Adj.
2. HS White Defect Adj.
3. White Defect Adj.
4. White Defect Adj. (FD white point)
5. White Defect Check
6. Black Defect Adj.
7. Release of Data Setting during Camera Adj.

[Adjusting method]
1) Click the [Start] button of the CAMERA Adjustment 5.
2) The Automatic Adjustment Program executes “1. Data Setting

during Camera Adj.”.

3) If “1. Data Setting during Camera Adj.” completed success-

fully, and the items from “2. HS White Defect Adj.” to “5.
White Defect Check” will be executed.

4) If “5. White Defect Check” completed successfully, the fol-

lowing message is displayed. Set the subject in accordance
with the message.

5) Click the [OK] button, and the “6. Black Defect Adj.” will be

executed.

6) Upon completion of “6. Black Defect Adj.”, “7. Release of

Data Setting during Camera Adj.” is executed.

7) Upon successful completion of all items of the CAMERA Ad-

justment 5, the following message is displayed. Click the [OK]
button.

6-27

HDR-UX3E/UX5/UX5E/UX7/UX7E_ADJ

“CAMERA Adjustment 6” is available only once after the
power is turned on. If the adjustment is retried, turn off the
power and turn on again.

[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Camera Adj.
2. Strobe Light Level Adj.
3. Strobe White Balance Adj.
4. Release of Data Setting during Camera Adj.

[Adjusting method]
1) Click the [Start] button of the CAMERA Adjustment 6.
2) The Automatic Adjustment Program executes “1. Data Setting

during Camera Adj.”.

3) Upon successful completion of the “1. Data Setting during

Camera Adj.”, the following message is displayed. Set the sub-
ject in accordance with the message.
(For the Flash adjustment box, refer to “4. Preparing the Flash
Adjustment Box” (see page 6-7).)

4) Press the [OK]  button, and the items “2. Strobe Light Level

Adj.” and “3. Strobe White Balance Adj.” will be executed.

5) Upon completion of “3. Strobe White Balance Adj.”, “4. Re-

lease of Data Setting during Camera Adj.” is executed

6) Upon successful completion of all items of the CAMERA Ad-

justment 6, the following message is displayed. Click the [OK]
button.

[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Camera Adj.
2. Steady Shot Check
3. Release of Data Setting during Camera Adj.

[Adjusting method]
1) Click the [Start] button of the CAMERA Adjustment 7.
2) The Automatic Adjustment Program executes “1. Data Setting

during Camera Adj.”.

3) Upon successful completion of the “1. Data Setting during

Camera Adj.”, the following message is displayed.
With the camcoder in stationary state, click the [OK] button.

4) If the [OK] button is clicked, “2. Steady Shot Check” is ex-

ecuted.
Upon successful completion of the “2. Steady Shot Check”,
the following message is displayed. Check that the steadyshot
function operates normally in accordance with the message.

5) If the [OK] button is clicked, “3. Release of Data Setting dur-

ing Camera Adj.” is executed.

6) Upon successful completion of all items of the CAMERA

Adjustment 7, the following message is displayed. Click the
[OK] button.

6-28

HDR-UX3E/UX5/UX5E/UX7/UX7E_ADJ

1

2

3

4

1

2

3

4

SE7202

SE7201

CM-077 BOARD (SIDE A)

PP

YY

YAW sensor
 sensitivity  

t

 S

7201

PITCH sensor sensitivity  

t

 S

7202

Perform this adjustment only when replacing the GYRO sensor or
lens block. When the microprocessor, circuit etc. is damaged, don’t
perform this adjustment but check the operations only.

Note down the sensitivity displayed on the GYRO sensor of the re-
pair parts. At this time, note down also to which board it was attached
to.
Be sure to check because if attached incorrectly, the screen will vi-
brate up and down or left and right during the steady shot operations.

The PITCH sensor and the YAW sensor are different parts.

The sensor incorporates a precision oscillator. Handle it with care as
if it dropped, the balance of oscillator will be disrupted and opera-
tions will not be performed properly.

Adjustment Block

11

Adjustment Page

80

Adjustment Address

7F12, 7F13

The sensor sensitivity of SE7201 and SE7202 of the CM-
077 board is written only repair parts.

Preparation:
1) Read the PITCH sensor (CM-077 board SE7202) sensitivity

written on repair parts, and named this as S

7202

.

2) Read the YAW sensor (CM-077 board SE7201) sensitivity writ-

ten on repair parts, and named this as S

7201

.

With the pins 1 and 2 of GYRO sensor placed in the lower posi-
tion, read the data value.

6 0

Hand Writing

1

2

4

3

For the sensor sensitivity value 60

6-29

HDR-UX3E/UX5/UX5E/UX7/UX7E_ADJ

Note down the PITCH/YAW data on the replacement lens for repair.

Adjustment Block

11

Adjustment Page

80

Adjustment Address

7F12, 7F13

The PITCH/YAW data of lens is written only repair parts.

Preparation:
1) Read the PITCH data written on repair parts, and named this

as L

1

.

2) Read the YAW data written on repair parts, and named this as

L

2

.

[Adjusting method]
1) Click the [Start] button of Camera Adjustment 8, and the fol-

lowing screen will appear.

2) Input the sensitivity of respective sensors (S

7201

, S

7202

) read at

“Preparation” into the screen.
If only either sensor was replaced, give a check to the checkbox
for the sensor not replaced at the lower left of the screen.

3) Input the PITCH/YAW data of lens (L

1

, L

2

) read at “Prepara-

tion” into the screen.
If the lens was not replaced, give a check to the checkbox at
the lower left of the screen.

4) Click the [OK] button, and the adjustment data is then calcu-

lated from the sensor sensitivity value and the calculation re-
sult is written to the memory in the camera.

5) Upon successful completion of the data writing, the following

screen will appear. Check that the steady shot function oper-
ates normally.

YAW data    

t

 L

2

PITCH/YAW Data

PITCH data 

t

 L

1

X.XX / X.XX