DOWNLOAD Sony HDR-SR1 / HDR-SR1E (serv.man4) Service Manual ↓ Size: 1.11 MB | Pages: 85 in PDF or view online for FREE

6-19

HDR-SR1/SR1E_ADJ

[Preparation (Using the flange back adjustment jig)]
(Illuminance: 300 to 400 lux)
1) Install the flange back adjustment jig so that the distance be-

tween it and the front of lens of camera is less than 3 cm.

2) Make the height of flange back adjustment jig and the camera

equal.

3) Check that the center of chart meets the center of shot image

screen with the zoom lens at TELE end and WIDE end respec-
tively.

[Adjusting method]
1) Click the [Start] button of the CAMERA Adjustment 2.
2) The Automatic Adjustment Program executes “1. Data Setting

during Camera Adj.”.

3) Upon successful completion of the “1. Data Setting during

Camera Adj.”, the following message is displayed. Set the sub-
ject by referring to “Preparation”.

4) If the [OK] button is clicked, “2. Flange Back Adj.” and “3.

Release of Data Setting during Camera Adj.” will be executed.

5) Upon successful completion of all items of the CAMERA

Adjustment 2, the following message is displayed. Click the
[OK] button.

Flange back adjustment jig

Below 3 cm

Camera

After adjustment, if the focusing to a subject located at in-
finity failed, increase the luminance or the illuminance of
the chart and perform readjustment.

[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Camera Adj.
2. Flange Back Adj.
3. Release of Data Setting during Camera Adj.

[Preparation (Using the minipattern box)]
1) The minipattern box is installed as shown in the following fig-

ure.

 The attachment lenses are not used.

2) Install the minipattern box so that the distance between it and

the front of lens of camera is less than 3 cm.

3) Make the height of minipattern box and the camera equal.
4) Check the output voltage of the regulated power supply is the

specified voltage 

± 0.01 Vdc.

5) Check that the center of Siemens star chart meets the center of

shot image screen with the zoom lens at TELE end and WIDE
end respectively.

Specified voltage: The specified voltage varies according to the

minipattern box, so adjustment the power sup-
ply output voltage to the specified voltage writ-
ten on the sheet which is supplied with the
minipattern box.

Minipattern box

Below 3 cm

Camera

Red (+)

Black (–)

Yellow (SENS +)

White (SENS –)

Black (GND)

Need not connected

Regulated power supply

Output voltage : Specified voltage 

±

 0.01 Vdc

Output current : more than 3.5 A

6-20

HDR-SR1/SR1E_ADJ

[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Camera Adj.
2. Flange Back (1) Adj.
3. Release of Data Setting during Camera Adj.

[Preparation]
1) Place the Flange back adjustment chart at 2 m position away

from the lens.

2) Check that the center of Flange back adjustment chart meets

the center of shot image screen with the zoom lens at TELE
end and WIDE end respectively.

[Adjusting method]
1) Click the [Start $1%] button of the CAMERA Adjustment 2.
2) The Automatic Adjustment Program executes “1. Data Setting

during Camera Adj.”.

3) Upon successful completion of the “1. Data Setting during

Camera Adj.”, the following message is displayed. Set the sub-
ject by referring to “Preparation”.

4) If the [OK] button is clicked, “2. Flange Back (1) Adj.” and “3.

Release of Data Setting during Camera Adj.” will be executed.

5) Upon successful completion of all items of the CAMERA

Adjustment 2 (1), the following message is displayed. Click
the [OK] button.

6) Perform “CAMERA Adjustment 2 (2)”.

[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Camera Adj.
2. Flange Back (2) Adj.
3. Release of Data Setting during Camera Adj.

[Preparation]
1) Set the zoom lens to the TELE end and expose a subject that is

more than 500 m away.
(subjects with clear contrast such as building, etc.)
(Nearby subjects less than 500 m away should not be in the
screen)

[Adjusting method]
1) Click the [Start $2%] button of the CAMERA Adjustment 2.
2) The Automatic Adjustment Program executes “1. Data Setting

during Camera Adj.”.

3) Upon successful completion of the “1. Data Setting during

Camera Adj.”, the following message is displayed. Set the sub-
ject by referring to “Preparation”.

4) If the [OK] button is clicked, “2. Flange Back (2) Adj.” will be

executed.
The following message is displayed during the execution of
adjustment, and then place the ND filter on the lens so as to
obtain the optimum image.

5) If “2. Flange Back Adj.” completed successfully, “3. Release

of Data Setting during Camera Adj.” will be executed.

6) Upon successful completion of all items of the CAMERA

Adjustment 2 (2), the following message is displayed. Click
the [OK] button.

6-21

HDR-SR1/SR1E_ADJ

[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Camera Adj.
2. Flange Back Check
3. Release of Data Setting during Camera Adj.

[Adjusting method]
1) Click the [Start] button of the CAMERA Adjustment 3.
2) The Automatic Adjustment Program executes “1. Data Setting

during Camera Adj.”.

3) Upon successful completion of the “1. Data Setting during

Camera Adj.”, the following message is displayed. Set the sub-
ject in accordance with the message.

4) If the [OK] button is clicked, “2. Flange Back Check” is ex-

ecuted. The following messages are displayed, and then oper-
ate the camera to make a check in accordance with the mes-
sages.

5) Upon completion of “2. Flange Back Check”, “3. Release of

Data Setting during Camera Adj.” is executed.

6) Upon successful completion of all items of the CAMERA

Adjustment 3, the following message is displayed. Click the
[OK] button.

6-22

HDR-SR1/SR1E_ADJ

[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Camera Adj.
2. F No. & ND Light Quality Standard Data Input
3. Mechanical Shutter Adj.
4. Linear Matrix Adj.
5. Picture Frame Setting (Color Reproduction Adjustment Frame)
6. Picture Frame Setting (All White Frame)
7. AWB Standard Data Input
8. LV Standard Data Input
9. AWB Adj.
10. Color Reproduction Adj.
11. Color Reproduction Check (Indoor HD)
12. Color Reproduction Check (Indoor SD)
13. Color Reproduction Check (Outdoor HD)
14. Color Reproduction Check (Outdoor SD)
15. AWB Check
16. Picture Frame Setting (Center Frame)
17. MAX GAIN Adj.
18. Release of Data Setting during Camera Adj.

[Adjusting method]
1) Select the model (NTSC Model or PAL Model) with the Model

Select radio button.

NTSC model: HDR-SR1
PAL model: HDR-SR1E

2) Click the [Start] button of the CAMERA Adjustment 4.
3) The Automatic Adjustment Program executes “1. Data Setting

during Camera Adj.”.

4) If “1. Data Setting during Camera Adj.” completed success-

fully, and the items from “2. F No. & ND Light Quality Stan-
dard Data Input” to “4. Linear Matrix Adj.” will be executed.

5) Upon successful completion of the “4. Linear Matrix Adj.”,

the following screen is displayed during the execution of “5.
Picture Frame Setting (Color Reproduction Adjustment
Frame)”. Set the subject in accordance with the message.

6) If the [OK] button is clicked, the following screen will appear,

and then adjust the zoom and the camera direction to set the
picture frame. After the setting finished, click the [End] but-
ton.

The buttons on this screen provide the following functions:

[Save the po

sition] button

Saves the camera zoom and focus position data.

[Load the position] button

Reads the camera zoom and focus position data saved last and
moves the camera zoom and focus to that position.

The zoom and focus position data are saved with “HDR-
SR1_ZoomFocusData.txt” file name in the same holder
as the Automatic Adjustment Program.
No position data can be read if this file is moved or de-
leted.

Only the latest position data can be saved. If the [Save
the position] button is clicked, the latest data are saved
over writing the previous data.