DOWNLOAD Sony DCR-TRV9 / DCR-TRV9E Service Manual ↓ Size: 34.67 MB | Pages: 127 in PDF or view online for FREE

5-13

Set the color reproduction conditions to optimum.

Subject

Color bar chart standard picture frame

Measurement Point

Display data of page A of the

Measuring Instrument

adjustment remote commander (Note)

Adjustment Page

F

Adjustment Address

53

Displayed data of page A of the adjusting remote commander.

A : XX : XX

S2
S1

Adjusting method:
1)

Select page: 6, address: 00, and set data: 01.

2)

Select page: 6, address: 01, set data: 01, and press the PAUSE
button of the adjustment remote commander.

3)

Select page: 6, address: 04, and set data: 16.

4)

Select page: F, address: 53, set data: 3F, and press the PAUSE
button of the adjustment remote commander.

5)

Select page A of the adjustment remote commander, and
compare the higher 2 digits (S1) and lower 2 digits (S2) of the
4-degits display data.
When S1 < S2

Perform steps 6) onwards.

When S1  S2
Perform steps “Processing after Completing Adjustments”.

6)

Select page: F, address: 53, set data: BF, and press the PAUSE
button of the adjustment remote commander.

Processing after Completing Adjustments:
1)

Select page: 6, address: 04, and set data: 00.

2)

Select page: 6, address: 01, set data: 00, and press the PAUSE
button of the adjustment remote commander.

3)

Select page: 6, address: 00, and set data: 00.

5-14

Adjust the color Separation matrix coefficient so that proper color
reproduction is produced.

Subject

Color bar chart standard picture frame

Measurement Point

Video output terminal

Measuring Instrument

Vectorscope

Adjustment Page

F

Adjustment Address

2E, 30, 44, 45

Specified Value

All color luminance points should
settle within each color reproduction
frame.

Switch setting:
1)

NIGHT SHOT switch ...................................................... OFF

Adjusting method:
1)

Select page: 6, address: 00, and set data: 01.

2)

Select page: 6, address: 01, set data: 3D, and press the PAUSE
button of the adjustment remote commander.

3)

Select page: F, address: 16, set data: 37, and press the PAUSE
button of the adjustment remote commander.

4)

Adjust the GAIN and PHASE of the vectorscope, and adjust
the burst luminance point to the burst position of the color
reproduction frame.

5)

Change the data of page: F, address: 2E, 30, 44 and 45, and
settle each color luminance point in each color reproduction
frame.

Be sure to press the PAUSE button of the adjustment remote
commander before changing the addresses. If not, the new data
will not be written to the memory.

6)

Press the PAUSE button of the adjustment remote commander.

Processing after Completing Adjustments:
1)

Select page: 6, address: 01, and set data: 00, and press the
PAUSE button of the adjustment remote commander.

2)

Select page: 6, address: 00, and set data: 00.

Fig. 5-1-9

Burst position

Burst position

5-15

Setting the minimum illumination.
If it is not consistent, the image level required for taking subjects in
low illuminance will not be produced (dark).

Subject

Clear chart
(Color bar standard picture frame)

Measurement Point

DDS display of LCD or TV monitor

Measuring Instrument

(Note)

Adjustment Page

F

Adjustment Address

2C

Specified Value

88 to 90 (NTSC)
88 to 90 (PAL)

The right two digits of the display data at the right bottom side of
the LCD and TV monitor is the object data.

CA 00 00XX

Object data

Switch setting:
1)

STEADY SHOT (Menu display) ..................................... OFF

2)

NIGHT SHOT switch ...................................................... OFF

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: D, address: 11, and set data: 02, and press the
PAUSE button of the adjustment remote commander.

3)

Select page: 6, address: 00, and set data: 01.

4)

Select page: 6, address: 04, and set data: 01.

5)

Select page: 6, address: 40, and set data: 02.

6)

Select page: 6, address: 56, and set data: 40.

7)

Select page: 6, address: 01, set data: 19 and press the PAUSE
button of the adjustment remote commander.

8)

Select page: F, address: 2C, change the data and adjust the DDS
display data (Note) to the specified value.

9)

Press the PAUSE button of the adjustment remote commander.

Processing after Completing Adjustments:
1)

Select page: D, address: 11, and set data: 00, and press the
PAUSE button of the adjustment remote commander.

2)

Select page: 0, address: 01, and set data: 00.

3)

Select page: 6, address: 00, and set data: 00.

4)

Select page: 6, address: 01, and set data: 00, and press the
PAUSE button of the adjustment remote commander.

5)

Select page: 6, address: 40, and set data: 00.

6)

Select page: 6, address: 56, and set data: 00.

Subject

Clear chart
(Color bar standard picture frame)

Adjustment Page

F

Adjustment Address

20 to 23, 3E, 3F

Perform “Color Reproduction Adjustment” before this adjustment.

Check that the data of page: 6, address: 02 is 00. If not, turn the
power of the unit OFF/ON.

Switch setting:
1)

NIGHT SHOT switch ...................................................... OFF

Adjusting method:
1)

Select page: 6, address: 00, and set data: 01.

2)

Wait for 2 seconds.

3)

Select page: 6, address: 01, and set data: 11, and press the
PAUSE button of the adjustment remote commander.

4)

Select page: 6, address: 01, and set data: 0D, and press the
PAUSE button of the adjustment remote commander.
(When the standard data is take in, the data will be automatically
input to page: F, address: 20 to 23, 3E, 3F.)

5)

Select page: 6, address: 02, and check that the data is “01”.

6)

Perform “Auto White Balance Adjustment”.

Processing after Completing Adjustments:
1)

Select page: 6, address: 01, and set data: 00, and press the
PAUSE button of the adjustment remote commander.

2)

Select page: 6, address: 00, and set data: 00.

5-16

Adjust to the proper auto white balance output data.
If it is not correct, auto white balance and color reproducibility will
be poor.

Subject

Clear chart
(Color bar standard picture frame)

Filter

Filter C14 for color temperature
correction

Measurement Point

DDS display of LCD or TV monitor

Measuring Instrument

(Note 1)

Adjustment Page

F

Adjustment Address

34, 35

Specified Value

R ratio: 2B40 to 2BC0
B ratio: 5E40 to 5EC0

Perform “Auto White Balance Standard Data Input” before this
adjustment.

The right four digits of the display data at the right bottom side of
the LCD and TV monitor is the object data.

CA 00 XXXX

Object data

Switch setting:
1)

NIGHT SHOT switch ...................................................... OFF

Adjusting method:
1)

Place the C14 filter for color temperature correction on the
lens.

2)

Select page: 0, address: 01, and set data: 01.

3)

Select page: D, address: 11, and set data: 02, and press the
PAUSE button of the adjustment remote commander.

4)

Select page: 6, address: 00, and set data: 01.

5)

Select page: 6, address: 01, and set data: 3F, and press the
PAUSE button of the adjustment remote commander.

6)

Select page: 6, address: 04, and set data: 04.

7)

Select page: F, address: 34, change the data and adjust the
average value of the DDS display data (Note 2) to the R ratio
specified value.

8)

Press the PAUSE button of the adjustment remote commander.

9)

Select page: 6, address: 04, and set data: 05.

10) Select page: F, address: 35, change the data and adjust the

average value of the DDS display data (Note 2) to the B ratio
specified value.

11) Press the PAUSE button of the adjustment remote commander.

Processing after Completing Adjustments:
1)

Select page: D, address: 11, and set data: 00, and press the
PAUSE button of the adjustment remote commander.

2)

Select page: 0, address: 01, and set data: 00.

3)

Select page: 6, address: 00, and set data: 00.

4)

Select page: 6, address: 01, and set data: 00, and press the
PAUSE button of the adjustment remote commander.

5)

Select page: 6, address: 04, and set data: 00.

Subject

Clear chart
(Color bar standard picture frame)

Filter

Filter C14 for color temperature
correction
ND filter 1.0 and 0.3

Measurement Point

Video output terminal

Measuring Instrument

Vectorscope

Specified Value

Fig. 5-1-10. (A) to (C)

Switch setting:
1)

NIGHT SHOT switch ...................................................... OFF

Checking method:
1)

Check that the lens is not covered with either filter.

2)

Select page: 6, address: 01, set data: 0F, and press the PAUSE
button of the adjustment remote commander.

3)

Check that the center of the white luminance point is within
the circle shown Fig. 5-1-10 (A).

4)

Select page: 6, address: 01, set data: 23, and press the PAUSE
button of the adjustment remote commander.

5)

Place the C14 filter on the lens.

6)

Check that the center of the white luminance point settles in
the circle shown Fig. 5-1-10 (B).

7)

Remove the C14 filter, and place the ND filter 1.3 (1.0 + 0.3)
on the lens.

8)

Check that the white luminance point stopped moving, and then
remove the ND filter 1.3.

9)

Check that the center of the white luminance point settles within
the circle shown Fig. 5-1-10 (C).

Processing after Completing Adjustments:
1)

Select page: 6, address: 01, and set data: 00, and press the
PAUSE button of the adjustment remote commander.