Sony DCR-SR30E / DCR-SR40 / DCR-SR40E (serv.man4) Service Manual ▷ View online
6-39
DCR-SR30E/SR40/SR40E_ADJ
1-10. ERROR
In the case of an error during the execution of adjustment, the
Automatic Adjustment Program interrupts the processing at that
point, and displays an error message, and then terminates the pro-
gram execution there.
Automatic Adjustment Program interrupts the processing at that
point, and displays an error message, and then terminates the pro-
gram execution there.
1-10-1. Error Message
When an error message is displayed, perform the remedy given
below, and then retry adjustment. If the error message is displayed
though the remedy was performed, the circuits will be faulty.
below, and then retry adjustment. If the error message is displayed
though the remedy was performed, the circuits will be faulty.
1.
Connect Error
Fig. 6-1-16
Symptom
USB communication with the set is abnormal.
Cause
•
USB cable is not inserted tightly.
•
Power supply is not installed correctly.
•
Communication with SeusCam is abnormal.
Remedy
•
Disconnect the USB cable once, and then re-
connect it tightly and check that the set is in
“USB Mode”.
connect it tightly and check that the set is in
“USB Mode”.
•
Install the power supply correctly.
•
Start the SeusCam and click the
[Connect]
to
check that the connection state is established.
2.
RESET the CAMERA and Try Again
Fig. 6-1-17
Symptom
The camera is not ready for adjustment.
Cause
Data error exists in the camera.
Remedy
Reset the camera.
3.
Adjustment Time Out
Fig. 6-1-18
Symptom
Adjustment does not finish within the specified
time.
time.
Cause
•
Adjustment conditions are wrong.
•
Data error exists in the camera.
Remedy
•
Check that the conditions such as a subject
are correct.
are correct.
•
Reset the camera.
4.
Adjustment NG
Fig. 6-1-19
Symptom
The adjusted data does not become the speci-
fied value.
fied value.
Cause
•
Adjustment conditions are wrong.
•
Data error exists in the camera.
Remedy
•
Check that the conditions such as a subject
are correct.
are correct.
•
Reset the camera.
This part indicates
the adjustment
item in which
an error occurred.
the adjustment
item in which
an error occurred.
This part indicates
the adjustment
item in which
an error occurred.
the adjustment
item in which
an error occurred.
6-40
DCR-SR30E/SR40/SR40E_ADJ
1-10-2. Precautions When an Error Occurred
The Automatic Adjustment Program sets the data for adjustment
before the adjustment starts. Accordingly, if the adjustment termi-
nates by an error, the data during the adjustment may be left in the
camera.
before the adjustment starts. Accordingly, if the adjustment termi-
nates by an error, the data during the adjustment may be left in the
camera.
Note:
With this data left in the camera, the camera will not oper-
ate normally.
ate normally.
In this case, the
[Release Data Setting]
button is displayed in
“red” on the screen as shown in Fig. 6-1-20 to Fig. 6-1-22. Click
the
the
[Release Data Setting]
button to cancel the data setting. When
the data setting is cancelled, the button color becomes “white”.
Video System Adjustment screen
Fig. 6-1-20
Camera System Adjustment screen
Fig. 6-1-21
LCD System Adjustment screen
Fig. 6-1-22
6-41
DCR-SR30E/SR40/SR40E_ADJ
6-2. SERVICE MODE
2-1.
ADJUSTMENT REMOTE COMMANDER
(RM-95)
(RM-95)
The adjustment remote commander (RM-95) is used for changing
the calculation coefficient in signal processing, EVR data, etc..
The adjustment remote commander (RM-95) performs bi-direc-
tional communication with the unit using the remote commander
signal line (LANC). The resultant data of this bi-directional com-
munication is written in the non-volatile memory.
the calculation coefficient in signal processing, EVR data, etc..
The adjustment remote commander (RM-95) performs bi-direc-
tional communication with the unit using the remote commander
signal line (LANC). The resultant data of this bi-directional com-
munication is written in the non-volatile memory.
1.
Using the Adjustment Remote Commander (RM-95)
1) Connect the adjustment remote commander to the LANC ter-
minal.
2) Set the HOLD switch of the adjustment remote commander
(RM-95) to “HOLD” (SERVICE position). If it has been prop-
erly connected, the LCD on the adjustment remote commander
(RM-95) will display as shown in Fig. 6-2-1.
erly connected, the LCD on the adjustment remote commander
(RM-95) will display as shown in Fig. 6-2-1.
Fig. 6-2-1
3) Operate the adjustment remote commander (RM-95) as fol-
lows.
•
Changing the page
The page increases when the EDIT SEARCH+ button is
pressed, and decreases when the EDIT SEARCH- button is
pressed. There are altogether 16 pages, from 0 to F.
The page increases when the EDIT SEARCH+ button is
pressed, and decreases when the EDIT SEARCH- button is
pressed. There are altogether 16 pages, from 0 to F.
•
Changing the address
The address increases when the FF (M) button is pressed,
and decreases when the REW (m) button is pressed. There
are altogether 256 addresses, from 00 to FF.
The address increases when the FF (M) button is pressed,
and decreases when the REW (m) button is pressed. There
are altogether 256 addresses, from 00 to FF.
•
Changing the data (Data setting)
The data increases when the PLAY (N) button is pressed,
and decreases when the STOP (x) button is pressed. There
are altogether 256 data, from 00 to FF.
The data increases when the PLAY (N) button is pressed,
and decreases when the STOP (x) button is pressed. There
are altogether 256 data, from 00 to FF.
•
Writing the adjustment data
The PAUSE button must be pressed to write the adjustment
data in the nonvolatile memory. (The new adjusting data will
not be recorded in the nonvolatile memory if this step is not
performed)
The PAUSE button must be pressed to write the adjustment
data in the nonvolatile memory. (The new adjusting data will
not be recorded in the nonvolatile memory if this step is not
performed)
4) After completing all adjustments, turn off the main power sup-
ply (8.4 V) once.
Page
Data
Address
Hexadecimal
notation
notation
LCD Display
Decimal notation
conversion value
conversion value
0 1 2 3 4 5 6 7 8 9 A B C D E F
0 1 2 3 4 5 6 7 8 9 A b c d E F
0 1 2 3 4 5 6 7 8 9 10 1112 13 14 15
2.
Precautions Upon Using the Adjustment Remote
Commander (RM-95)
Commander (RM-95)
Mishandling of the adjustment remote commander may erase the
correct adjustment data at times. To prevent this, it is recommended
that all adjustment data be noted down before beginning adjust-
ments and new adjustment data after each adjustment.
correct adjustment data at times. To prevent this, it is recommended
that all adjustment data be noted down before beginning adjust-
ments and new adjustment data after each adjustment.
6-42
DCR-SR30E/SR40/SR40E_ADJ
2-2.
ADJUSTMENT REMOTE COMMANDER
(NEW LANC JIG)
(NEW LANC JIG)
The adjustment remote commander (New LANC Jig) is used for
changing the calculation coefficient in signal processing, EVR data,
etc. The adjustment remote commander (New LANC Jig) performs
bi-directional communication with the unit using the remote com-
mander signal line (LANC). The resultant data of this bi-direc-
tional communication is written in the non-volatile memory.
changing the calculation coefficient in signal processing, EVR data,
etc. The adjustment remote commander (New LANC Jig) performs
bi-directional communication with the unit using the remote com-
mander signal line (LANC). The resultant data of this bi-direc-
tional communication is written in the non-volatile memory.
1.
Using the Adjustment Remote Commander
(New LANC Jig))
(New LANC Jig))
1) Connect the adjustment remote commander (New LANC Jig)
to the LANC terminal via the LANC cable (J-6082-442-A).
2) Set the slide switch of the adjustment remote commander (New
LANC Jig) to “SERVICE” (SERVICE position). If it has been
properly connected, the LCD on the adjustment remote com-
mander (New LANC Jig) will display as shown in Fig. 6-2-2.
properly connected, the LCD on the adjustment remote com-
mander (New LANC Jig) will display as shown in Fig. 6-2-2.
Fig. 6-2-2
3) Operate the adjustment remote commander (New LANC Jig)
as follows.
•
Changing the page
The page increases when the Page+ (M) button is pressed,
and decreases when the Page– (m) button is pressed.
The page increases when the Page+ (M) button is pressed,
and decreases when the Page– (m) button is pressed.
•
Changing the address
The address increases when the ADD+ (N) button is
pressed, and decreases when the ADD
The address increases when the ADD+ (N) button is
pressed, and decreases when the ADD
−
(X) button is
pressed. There are altogether 256 addresses, from 00 to FF.
•
Changing the data (Data setting)
The data increases when the Data+ button is pressed, and
decreases when the Data
The data increases when the Data+ button is pressed, and
decreases when the Data
−
button is pressed. There are alto-
gether 256 data, from 00 to FF.
•
Writing the adjustment data
The Write (x) button must be pressed to write the adjust-
ment data in the nonvolatile memory. (The new adjusting
data will not be recorded in the nonvolatile memory if this
step is not performed)
The Write (x) button must be pressed to write the adjust-
ment data in the nonvolatile memory. (The new adjusting
data will not be recorded in the nonvolatile memory if this
step is not performed)
4) After completing all adjustments, turn off the main power sup-
ply (8.4 V) once.
2. Precautions Upon Using
the Adjustment Remote Commander (New LANC Jig)
Mishandling of the adjustment remote commander (New LANC
Jig) may erase the correct adjustment data at times. To prevent
this, it is recommended that all adjustment data be noted down
before beginning adjustments and new adjustment data after each
adjustment.
Jig) may erase the correct adjustment data at times. To prevent
this, it is recommended that all adjustment data be noted down
before beginning adjustments and new adjustment data after each
adjustment.
Page
Address
Data
p:00 a:00 d:00
Click on the first or last page to see other DCR-SR30E / DCR-SR40 / DCR-SR40E (serv.man4) service manuals if exist.