DOWNLOAD Sony DCR-SR210E / DCR-SR220 / DCR-SR220D / DCR-SR220E / HDR-SR10 / HDR-SR10D / HDR-SR10E (serv.man3) Service Manual ↓ Size: 739.44 KB | Pages: 48 in PDF or view online for FREE

6-32

DCR-SR210E/SR220/SR220D/SR220E/
HDR-SR10/SR10D/SR10E_ADJ

[Adjusting method]
1) Click the [Start] button of Camera Adjustment 8, and the fol-

lowing screen will appear.

2) Input the sensitivity of respective sensors (S

9501

, S

9502

) read at

“Preparation” into the screen.
If only either sensor was replaced, give a check to the checkbox
for the sensor not replaced at the lower left of the screen.

3) Input the PITCH/YAW data of lens (L

1

, L

2

) read at “Prepara-

tion” into the screen.
If the lens was not replaced, give a check to the checkbox at
the lower left of the screen.

In order to get the correct value for the adjustment, it is
necessary to input a decimal point (“period” or  “com-
ma”) as same format as windows setting because “Nu-
meric Value Format” depend on the language. (F:123
456 789,00, GB:123,456,789.00, D:123.456.789,00)
“Numeric Value Format” setting is available in “Con-
trol Panel”-“Regional and Language Options”.

4) Click the [OK] button, and the adjustment data is then calcu-

lated from the sensor sensitivity value and the calculation re-
sult is written to the memory in the camera.

5) Upon successful completion of the data writing, the following

massage will be displayed, and then turn off the power of cam-
era and turn it on again.

6) After the Camera started, click the [OK]  button of the mes-

sage, and the data value will be clecked. If the data value is
normal, the following massage will be displayed. Check that
the steady shot function operates normally.

Note down the PITCH/YAW data on the replacement lens for repair.

Adjustment Block

11

Adjustment Page

8F

Adjustment Address

FF70, FF71

The PITCH/YAW data of lens is written only repair parts.

Preparation:
1) Read the PITCH data written on repair parts, and named this

as L

1

.

2) Read the YAW data written on repair parts, and named this as

L

2

.

YAW data    

t

 L

2

PITCH/YAW Data

PITCH data 

t

 L

1

P.PP / Y.YY

P.PP / Y.YY

6-33

DCR-SR210E/SR220/SR220D/SR220E/
HDR-SR10/SR10D/SR10E_ADJ

Click the [LCD SYSTEM ADJUSTMENT] button on the Main Menu
screen, and the “LCD SYSTEM ADJUSTMENT” screen in Fig.
6-1-20 will appear.

1

[To Menu] button
The Main Menu screen comes back.

2

[Start] button
Each adjustment “LCD Adjustment” or “Touch Panel Adjust-
ment” starts.

The adjustment items of LCD system adjustment are as listed in
Table 6-1-5. The Automatic Adjustment Program executes the ad-
justment items if the LCD Adjustment Start button is clicked.

VCO Adj.

10

60

1050 (NTSC model),
1051 (PAL model)

Contrast Adj.

10

60

1058

V-COM Adj.

10

60

1052

Transmissive Mode White Balance Adj.

10

60

1056, 1057

Reflective Mode White Balance Adj.

10

60

107B, 107C

Sample Hold Phase Adj.

10

60

105F

Touch Panel
Adjustment

Touch Panel Adj.

(Note)

LCD
Adjustment

The adjustment data cannot be read or written from the SeusEX.

2

1

6-34

DCR-SR210E/SR220/SR220D/SR220E/
HDR-SR10/SR10D/SR10E_ADJ

4) If the [End] button is clicked, the following screen is displayed

during the execution of “4. Transmissive Mode White Balance
Adj.”. Check that the LCD screen is not colored. If colored,
using the [Up]/[Down] button on the screen, adjust so that the
LCD screen is not colored. After the adjustment, click the [End]
button in the screen.

5) If the [End] button is clicked, “5. Reflective Mode White Bal-

ance Adj.” and “6. Sample Hold Phase Adj.” will be executed.
The following screen is displayed during the execution of “6.
Sample Hold Phase Adj.”. Using the [Up]/[Down]  button on
the screen, adjust so that the 2nd portion A of the LCD screen
is Brightest. After the adjustment, click the [End] button in the
screen.

6) If the [End] button is clicked, “7. Release of Data Setting dur-

ing LCD Adj.” will be executed.

7) Upon successful completion of all item the LCD Adjustment,

the following message is displayed. Click the [OK] button.

[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during LCD Adj.
2. LCD Automatic Adj.

(VCO Adj., Contrast Adj.)

3. V-COM Adj.
4. Transmissive Mode White Balance Adj.
5. Reflective Mode White Balance Adj.
6. Sample Hold Phase Adj.
7. Release of Data Setting during LCD Adj.

[Adjusting method]
1) Click the [Start] button of the LCD Adjustment.
2) The Automatic Adjustment Program executes the “1. Data

Setting during LCD Adj.” and “2. LCD Automatic Adj.”.

3) After that, the following screen is displayed during the execu-

tion of “3. V-COM Adj.”. Using the [Up]/[Down] button on the
screen, adjust so that the brightness of portions A and B on the
LCD panel is equal. After the adjustment, click the [End] but-
ton in the screen.

6-35

DCR-SR210E/SR220/SR220D/SR220E/
HDR-SR10/SR10D/SR10E_ADJ

[Automatic Adjustment Program execution items and
sequence]
1. Touch Panel Adj.
2. Release of Data Setting during LCD Adj.

[Adjusting method]
1) Click the [Start] button of the Touch Panel Adjustment.
2) The Automatic Adjustment Program executes the “1. Touch

Panel Adj.”. The following message is displayed, and then
adjust the LCD screen in accordance with the instructions given
on the screen. After the adjustment, click the [OK] button in
the message window.

3) If the [OK] button is clicked, “2. Release of Data Setting dur-

ing LCD Adj.” will be executed.

4) Upon successful completion of all item the Touch Panel Ad-

justment, the following message is displayed. Click the [OK]
button.