Sony DCR-SR210E / DCR-SR220 / DCR-SR220D / DCR-SR220E / HDR-SR10 / HDR-SR10D / HDR-SR10E (serv.man3) Service Manual ▷ View online
6-8
DCR-SR210E/SR220/SR220D/SR220E/
HDR-SR10/SR10D/SR10E_ADJ
HDR-SR10/SR10D/SR10E_ADJ
4.
Setting of Adjustment Mode
Before performing the adjustment, “Setting of Adjustment Mode”
is required.
is required.
[Setting method]
1) Connect the Camcorder to the PC with a USB cable, and turn
1) Connect the Camcorder to the PC with a USB cable, and turn
on the power switch.
2) The USB SELECT menu will appear on the LCD screen of
the Camcorder, and then select “COMPUTER” to establish
the connection.
the connection.
3) Start the Automatic Adjustment Program, and click the [Con-
nect] button on the Main Menu screen.
4) When the following message is displayed, turn off and on again
the power switch of the Camcorder.
Note:
Turning off and on the power switch causes the
Camcorder to be switched to the Adjustment Mode.
After the Camcorder restarted, click the [OK] button in
the message window.
Camcorder to be switched to the Adjustment Mode.
After the Camcorder restarted, click the [OK] button in
the message window.
5) Upon successful completion of the settings in the Adjustment
Mode, the operation of each button on the Main Menu screen
is enabled.
is enabled.
5.
Release of Adjustment Mode
To finish the adjustment, be sure to perform “Release of Adjust-
ment Mode”.
ment Mode”.
[Releasing method]
1) Click the [END] button on the Main Menu screen.
2) When the following message is displayed, releasing of adjust-
1) Click the [END] button on the Main Menu screen.
2) When the following message is displayed, releasing of adjust-
ment mode has completed. Click the [OK] button in the mes-
sage window to exit the Automatic Adjustment Program.
sage window to exit the Automatic Adjustment Program.
Note:
The Camcorder switches to the normal mode by turn-
ing off and on the power switch. After the adjustment
finished, turn off and on again the power switch of the
Camcorder to confirm that the USB SELECT menu is
displayed.
ing off and on the power switch. After the adjustment
finished, turn off and on again the power switch of the
Camcorder to confirm that the USB SELECT menu is
displayed.
6-9
DCR-SR210E/SR220/SR220D/SR220E/
HDR-SR10/SR10D/SR10E_ADJ
HDR-SR10/SR10D/SR10E_ADJ
1-3.
HDD SYSTEM ADJUSTMENTS
When the HDD is replaced, the following VBScript files are used.
The Automatic Adjustment Program (HDR-SR10 Series Auto-Adj
Ver_1.[]r[][].exe or DCR-SR220 Series Auto-Adj Ver_1.[]r[][].exe)
is not used.
• CheckHDDError_After2008.vbe
• SetFactoryCheckDefault_After2008.vbe
• SetFactoryCheckFull_After2008.vbe
• ExecAfterFactoryCheck_2008.vbe
The Automatic Adjustment Program (HDR-SR10 Series Auto-Adj
Ver_1.[]r[][].exe or DCR-SR220 Series Auto-Adj Ver_1.[]r[][].exe)
is not used.
• CheckHDDError_After2008.vbe
• SetFactoryCheckDefault_After2008.vbe
• SetFactoryCheckFull_After2008.vbe
• ExecAfterFactoryCheck_2008.vbe
For the VBScript files ([][][][][][][].vbe), the program is executed
by double-clicking the file.
by double-clicking the file.
Note 1:
The VBScript files can only be used on the PC in which
the SeusEX is installed.
the SeusEX is installed.
Note 2:
The VBScript file to be used must include 2008 in the
file name.
file name.
6-10
DCR-SR210E/SR220/SR220D/SR220E/
HDR-SR10/SR10D/SR10E_ADJ
HDR-SR10/SR10D/SR10E_ADJ
Message is checked.
When message is
“No Error”
“No Error”
When message is
“Error Detected”
“Error Detected”
Connect the camcorder to the PC
with a USB cable, and turn on the
power switch.
with a USB cable, and turn on the
power switch.
The USB SELECT menu will appear
on the LCD screen of the camcorder,
and the select “USB CONNECT” to
establish the connection.
on the LCD screen of the camcorder,
and the select “USB CONNECT” to
establish the connection.
Execte the “CheckHDDError_After2008.vbe”.
(Double-click the file.)
(Double-click the file.)
Replacing the HDD is unneccessary.
Start
End
A
B
(See page 6-11)
(See page 6-11)
1.
HDD Replacement Procedure
Note 1:
40GB: HDR-SR10/SR10E
60GB: DCR-SR210E/SR220/SR220E
120GB: DCR-SR220D, HDR-SR10D
60GB: DCR-SR210E/SR220/SR220E
120GB: DCR-SR220D, HDR-SR10D
Note 2:
Select correct capacity and retry, if the HDD capacity
setting was wrong.
setting was wrong.
6-11
DCR-SR210E/SR220/SR220D/SR220E/
HDR-SR10/SR10D/SR10E_ADJ
HDR-SR10/SR10D/SR10E_ADJ
Note:
During the execution of Factory Check, the LCD screen of
the camcorder becomes gray, and the ACCESS lamp be-
comes dark and light.
When the Factory Check finished, the LCD screen changes
as follows:
the camcorder becomes gray, and the ACCESS lamp be-
comes dark and light.
When the Factory Check finished, the LCD screen changes
as follows:
When Factory Check is OK: Camera image display
When Factory Check is NG: Blue display
When Factory Check is NG: Blue display
Is replacement HDD new one?
No
Reused HDD
Reused HDD
Yes
New HDD
New HDD
Turn off the power of camcorder.
Turning on the power of camcorder
will start automatic Factory Check.
Wait until Factory Check completed. (Note)
[EST. PROCESS TIME]
Default: 6 min.
Full:
Full:
40GB About 2 hour 36 min.
60GB About 3 hour 36 min.
120GB About 7 hour 15 min.
60GB About 3 hour 36 min.
120GB About 7 hour 15 min.
Replace the HDD.
Execte the
“SetFactoryCheckDefault_After2008.vbe”.
(Double-click the file.)
“SetFactoryCheckDefault_After2008.vbe”.
(Double-click the file.)
Wait until “JOB Success”
message is displayed.
(several seconds)
message is displayed.
(several seconds)
Wait until “JOB Success”
message is displayed.
(several seconds)
message is displayed.
(several seconds)
Wait until “JOB Success”
message is displayed.
(several seconds)
message is displayed.
(several seconds)
Execte the
“SetFactoryCheckFull_After2008.vbe”.
(Double-click the file.)
“SetFactoryCheckFull_After2008.vbe”.
(Double-click the file.)
Execte the
“ExecAfterFactoryCheck_2008.vbe”.
(Double-click the file.)
“ExecAfterFactoryCheck_2008.vbe”.
(Double-click the file.)
B
A
(See page 6-10)
(See page 6-10)
Click on the first or last page to see other DCR-SR210E / DCR-SR220 / DCR-SR220D / DCR-SR220E / HDR-SR10 / HDR-SR10D / HDR-SR10E (serv.man3) service manuals if exist.