Sony DCR-SR190E / DCR-SR200 / DCR-SR200C / DCR-SR200E / DCR-SR290E / DCR-SR300 / DCR-SR300C / DCR-SR300E (serv.man2) Service Manual ▷ View online
1-5
DCR-SR190E/SR200/SR200C/SR200E/SR290E/SR300/SR300C/SR300E_L2
ENGLISH
JAPANESE
ENGLISH
JAPANESE
1-3-3. E : 62 : 12 [Shift Lens Overheating (Yaw)] Occurred
Connect by the SeusEX and perform the following process.
Order Block Page Address Data
Procedure
1
11
80
6BB2
01
Write the data.
2
11
80
7D47
F0
Write the data.
3
11
80
7D49
01
Write the data. (Note 1)
4
11
80
7D49
00
Write the data.
5
11
80
7D47
10
Write the data.
6
11
80
7D49
01
Write the data. (Note 1)
7
11
80
7D49
00
Write the data.
8
11
80
6BB2
00
Write the data.
9
Check if the shift lens moves while setting the order 2 to 7. If the shift lens does not move,
replace the lens block (Note 2). When the shift lens moved, proceed to the order 10.
replace the lens block (Note 2). When the shift lens moved, proceed to the order 10.
10
While setting the order 2 to 7, measure with an oscilloscope the output voltage of R5737 in the
periphery of IC5703 on the VC-492 board to check the output voltage varies.
periphery of IC5703 on the VC-492 board to check the output voltage varies.
11
If the output voltage does not vary, replace the lens block (Note 2). When the output voltage
varied, proceed to the order 12.
varied, proceed to the order 12.
12
Turn the power OFF.
While measuring with an oscilloscope the output voltage of R5792 in the periphery of IC5703
13
on the VC-492 board, turn the power ON to check that the output voltage immediately after the
power on change as shown in Fig. 2.
power on change as shown in Fig. 2.
If the output voltage change as shown in Fig. 2, replace the lens block (Note 2). If it does not
14
change as shown in Fig. 2, inspect the camera control circuit (IC1803 of VC-492 board) pe
riphery.
riphery.
Note 1: Finish this operation within 10 seconds. If it is likely to take more than 10 seconds, set block: 11, page: 80, address:
7D49, data: 00, and then retry.
Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
handheld operation.
1-3-4. E : 62 : 20 [Abnormality of Thermistor] Occurred
Order
Procedure
1
Turn the power ON.
2
Check that R1846 in the periphery of IC1803 on the VC-492 board is 0
Ω and energizes. If it is not energizes, replace the R1846.
When R1846 is 0
Ω and energizes, replace the lens block (Note).
3
Check that no error occurs, after replacing the lens block and performing the necessary adjustment. If an error occurs, inspect
the camera control circuit (IC1803 of VC-492 board) periphery.
the camera control circuit (IC1803 of VC-492 board) periphery.
Note: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
handheld operation.
1-6
DCR-SR190E/SR200/SR200C/SR200E/SR290E/SR300/SR300C/SR300E_L2
ENGLISH
JAPANESE
ENGLISH
JAPANESE
1-4. PRECAUTION ON REPLACING THE VC-492 BOARD
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Refer to Service Manual ADJ, and perform “DESTINATION DATA WRITE”.
Refer to Service Manual ADJ, and perform “DESTINATION DATA WRITE”.
USB SERIAL No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Refer to Service Manual ADJ, and perform “USB SERIAL No. INPUT”.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Refer to Service Manual ADJ, and perform “USB SERIAL No. INPUT”.
1-5. USING SERVICE JIG
Connect the extension cable between CN4008 on the DA-042 board and CN1005 on the VC-492 board.
CN4008
CN1005
DA-042 board (side B)
VC-492 board (side B)
Extension cable (100P)
1-6. PROCESS AFTER FIXING FLASH ERROR
When “FLASH error” (Self-diagnosis Code E : 91 : 01) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash
is changed automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Flash error code can be initialized by execution of “Clear All record-data”.
is changed automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Flash error code can be initialized by execution of “Clear All record-data”.
Note:
For “Clear All record-data”, refer to Service Manual, ADJ (“7. Record Data” of “2-2. SERVICE MODE”).
Ver. 1.2 2007.06
1-7
DCR-SR190E/SR200/SR200C/SR200E/SR290E/SR300/SR300C/SR300E_L2
(ENGLISH)
1-7. PRECAUTION ON REPLACING
1-7. PRECAUTION ON REPLACING
THE CABINET BOTTOM
(DCR-SR190E)
(DCR-SR190E)
* Cabinet bottom is registered as “bottom, cabinet” in the parts list.
The model display adopts the laser printing method.Therefore, the
cabinet bottom (BOTTOM, CABINET) for replacement differs
depending on the destination.
As similar displays are provided, choose the suitable one for order.
cabinet bottom (BOTTOM, CABINET) for replacement differs
depending on the destination.
As similar displays are provided, choose the suitable one for order.
Note1: After replacing the cabinet bottom (BOTTOM, CABINET),
the serial number for it will be changed to the one exclusive for
service use.
Inform a customer of the serial number change and change the serial
number in the repair data.
the serial number for it will be changed to the one exclusive for
service use.
Inform a customer of the serial number change and change the serial
number in the repair data.
(JAPANESE)
1-7. キャビネットボトム 交換時の注意
1-7. キャビネットボトム 交換時の注意
(DCR-SR190E)
* キャビネットボトムは部品表で“bottom,
cabinet”とし
て登録されています。
機種の表示部はレーザー印字方式を採用しております。
この為，交換用のキャビネットボトムは仕向けにより異な
ります。類似の表示もありますので，該当するものを選ん
この為，交換用のキャビネットボトムは仕向けにより異な
ります。類似の表示もありますので，該当するものを選ん
で注文して下さい。
注意1 : キャビネットボトム交換後はシリアルナンバーが
サービス専用のシリアルナンバーに変更されます。お客様
サービス専用のシリアルナンバーに変更されます。お客様
への案内と修理データのシリアルナンバー変更を行ってく
ださい。
ださい。
DCR-SR190E
(AEP, UK Models)
(AEP, UK Models)
Part No.
A-1246-495-A
Description
BOTTOM (SR-190E-1), CABINET
Serial No.
1-8
DCR-SR190E/SR200/SR200C/SR200E/SR290E/SR300/SR300C/SR300E_L2
(ENGLISH)
1-8. PRECAUTION ON REPLACING
1-8. PRECAUTION ON REPLACING
THE CABINET BOTTOM
(DCR-SR200)
(DCR-SR200)
* Cabinet bottom is registered as “bottom, cabinet” in the parts list.
The model display adopts the laser printing method.Therefore, the
cabinet bottom (BOTTOM, CABINET) for replacement differs
depending on the destination.
As similar displays are provided, choose the suitable one for order.
cabinet bottom (BOTTOM, CABINET) for replacement differs
depending on the destination.
As similar displays are provided, choose the suitable one for order.
Note1: After replacing the cabinet bottom (BOTTOM, CABINET),
the serial number for it will be changed to the one exclusive for
service use.
Inform a customer of the serial number change and change the serial
number in the repair data.
the serial number for it will be changed to the one exclusive for
service use.
Inform a customer of the serial number change and change the serial
number in the repair data.
Note 2: When replacing the cabinet bottom for US, affix the
“Manufacturing year” label and the “Factory” label on the specified
location as shown in the figure.
The replacement caution label and inset (how to affix) are supplied
together with the cabinet bottom.
“Manufacturing year” label and the “Factory” label on the specified
location as shown in the figure.
The replacement caution label and inset (how to affix) are supplied
together with the cabinet bottom.
Note 3: When replacing the cabinet bottom for Korea, affix the
“Manufacturing year” label on the specified location as shown in
the figure.
The replacement caution label and inset (how to affix) are supplied
together with the cabinet bottom.
“Manufacturing year” label on the specified location as shown in
the figure.
The replacement caution label and inset (how to affix) are supplied
together with the cabinet bottom.
(JAPANESE)
1-8. キャビネットボトム 交換時の注意
1-8. キャビネットボトム 交換時の注意
(DCR-SR200)
* キャビネットボトムは部品表で“bottom,
cabinet”とし
て登録されています。
機種の表示部はレーザー印字方式を採用しております。
この為，交換用のキャビネットボトムは仕向けにより異な
この為，交換用のキャビネットボトムは仕向けにより異な
ります。類似の表示もありますので，該当するものを選ん
で注文して下さい。
で注文して下さい。
注意1 : キャビネットボトム交換後はシリアルナンバーが
サービス専用のシリアルナンバーに変更されます。お客様
への案内と修理データのシリアルナンバー変更を行ってく
への案内と修理データのシリアルナンバー変更を行ってく
ださい。
注意2: US仕向けキャビネットボトムを交換した際は「製
造年月」を表すラベルと，「製造所」を表すラベルを図の
造年月」を表すラベルと，「製造所」を表すラベルを図の
指定位置に貼り付けてください。
なお，キャビネットボトムには時期表示ラベル，投げ込み
(ラベル貼り方)がセットで供給されます。
注意3 : K o r e a n 仕向けキャビネットボトムを交換した際
は，「製造年月」を表すラベルを図の指定位置に貼り付け
てください。
てください。
なお，キャビネットボトムには時期表示ラベル，投げ込み
(ラベル貼り方)がセットで供給されます。
(ラベル貼り方)がセットで供給されます。
DCR-SR200
(US Model)
(US Model)
DCR-SR200
(Korean Model)
(Korean Model)
DCR-SR200
(Canadian Model)
(Canadian Model)
DCR-SR200
(E Model)
(E Model)
Serial No.
Part No.
A-1246-487-A
SKD
2006.11
6D
Description
BOTTOM (SR-200U), CABINET
Part No.
A-1246-488-A
Description
BOTTOM (SR-200KR), CABINET
Part No.
A-1246-489-A
Description
BOTTOM (SR-200CA), CABINET
Serial No.
Serial No.
Part No.
A-1246-490-A
Description
BOTTOM (SR-200), CABINET
Serial No.
*
Factory
* Affix the label
* Affix the label
*
Manufacturing year
*
Manufacturing year
Click on the first or last page to see other DCR-SR190E / DCR-SR200 / DCR-SR200C / DCR-SR200E / DCR-SR290E / DCR-SR300 / DCR-SR300C / DCR-SR300E (serv.man2) service manuals if exist.