Sony DCR-SR190E / DCR-SR200 / DCR-SR200C / DCR-SR200E / DCR-SR290E / DCR-SR300 / DCR-SR300C / DCR-SR300E (serv.man2) Service Manual ▷ View online
2-1
2. DISASSEMBLY
DCR-SR190E/SR200/SR200C/SR200E/SR290E/SR300/SR300C/SR300E_L2
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, dont’ pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, dont’ press down at wire of connector.
It is possible that a wire is snapped.
DISCHARGING OF THE ST-159 BOARD’S CHARGING CAPACITOR (C5206)
The charging capacitor (C5206) of the ST-159 board is charged
up to the maximum 330 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
up to the maximum 330 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 k
a resistor of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
prevent electrical shock.
1 k
Ω
/1 W
Wrap insulating tape.
NOTE FOR DISCONNECTING THE HARNESS
When disconnecting the harness, do not pull the harness part but
pull off the connector body with tweezers etc.
pull off the connector body with tweezers etc.
Harness
Tweezers etc.
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between the two points
with the short jig about 10 seconds.
Short-circuit between the two points
with the short jig about 10 seconds.
R:1 k
Ω
/1 W
Part code:
1-215-869-11)
1-215-869-11)
2-2
DCR-SR190E/SR200/SR200C/SR200E/SR290E/SR300/SR300C/SR300E_L2
2-1. DISASSEMBLY
2-1-1. OVERALL ASSEMBLY-1
HELP
HELP
EXPLODED VIEW
HARDWARE LIST
Follow the disassembly in the numerical order given.
1
Cabinet Bottom Section (
1
-1 to
1
-2)
2
Cabinet (L) Section (
2
-1 to
2
-3)
3
HDD (
3
-1 to
3
-4)
4
Cabinet (R) Section (
4
-1 to
4
-5)
C
A
A
B
B
C
3
-1
3
-3
3
-4
1
Cabinet Bottom
Section
3
HDD
4
Cabinet (R)
Section
2
Cabinet (L) Section
1
-1 (#2)
2
-1
(#10)
2
-3
(#10)
4
-1 (#10)
4
-5
4
-2 (#10)
4
-3 (#2)
3
-2 (#14)
4
-4 (#2)
2
-2 (#10)
1
-2 (#2)
2-3
DCR-SR190E/SR200/SR200C/SR200E/SR290E/SR300/SR300C/SR300E_L2
2-1-2. OVERALL ASSEMBLY-2
EXPLODED VIEW
HARDWARE LIST
Follow the disassembly in the numerical order given.
1
Switch Block (
1
-1 to
1
-6)
2
Front Panel Section (
2
-1 to
2
-6)
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between the two points
with the short jig about 10 seconds.
Short-circuit between the two points
with the short jig about 10 seconds.
R:1 k
Ω
/1 W
(Part code:
1-215-869-11)
1-215-869-11)
2
Front Panel Section
1
Switch Block
2
-3 (#10)
2
-2 (#10)
2
-1
2
-4 (claw)
2
-5 (claw)
2
-6 (claw)
1
-1
1
-2
1
-4 (#2)
1
-5 (#2)
1
-6 (#2)
1
-3
FP-609 FLEXIBLE BOARD
CONTROL SWITCH
BLOCK FLEXIBLE
BOARD
BLOCK FLEXIBLE
BOARD
FP-611 FLEXIBLE
BOARD
BOARD
CN4005
CN4007
DA-042 BOARD
Note for disassembly Flexible Boards
2-4
DCR-SR190E/SR200/SR200C/SR200E/SR290E/SR300/SR300C/SR300E_L2
2-1-3. OVERALL ASSEMBLY-3
EXPLODED VIEW
HARDWARE LIST
Follow the disassembly in the numerical order given.
1
DA-042 board (
1
-1 to
1
-6)
2
VC-492 (
2
-1 to
2
-9)
3
Lens Block-1 (
3
-1 to
3
-3)
Note
Grip the point of the figure below when you remove the
B to B connector of DA-042 board.
DA-042 board curves when the points other than the
figure below are gripped, and IC on board is damaged.
Grip the point of the figure below when you remove the
B to B connector of DA-042 board.
DA-042 board curves when the points other than the
figure below are gripped, and IC on board is damaged.
B to B connector
Grip the point.
D
D
A
C
C
D
A
B
B
FP-613
DA-042
VC-492
DA-042
VC-492
1
DA-042 Board
1
-1 (#14)
1
-2 (#14)
1
-4
1
-5
1
-3
1
-6
2
VC-492 Board
2
-1 (#14)
2
-6 (#3)
3
-2 (#14)
3
-1 (#14)
2
-7 (#3)
2
-8 (#3)
2
-9
2
-3
2
-5
2
-4
2
-2 (#14)
3
-3
3
Lens Block-1
Click on the first or last page to see other DCR-SR190E / DCR-SR200 / DCR-SR200C / DCR-SR200E / DCR-SR290E / DCR-SR300 / DCR-SR300C / DCR-SR300E (serv.man2) service manuals if exist.