Sony DCR-PC330 / DCR-PC330E (serv.man2) Service Manual ▷ View online
— 5 —
DCR-PC330/PC330E
TABLE OF CONTENTS
1.
SERVECE NOTE
1-1.
SERVICE NOTE ····························································· 1-1
1.
POWER SUPPLY DURING REPAIRS ·························· 1-1
2.
TO TAKE OUT A CASSETTE WHEN NOT EJECT
(FORCE EJECT) ····························································· 1-1
(FORCE EJECT) ····························································· 1-1
3.
HOW TO OPEN THE FLASH WHEN THE FLASH
DOSEN’T OPEN ···························································· 1-1
DOSEN’T OPEN ···························································· 1-1
4.
DISCHARGING OF THE FLASHLIGHT POWER
SUPPLY CAPACITOR ··················································· 1-2
SUPPLY CAPACITOR ··················································· 1-2
5.
NOTES ON HANDLING THE LASER DIODE
[LASER UNIT (D7609 of FP-706 flexible)] ·················· 1-3
[LASER UNIT (D7609 of FP-706 flexible)] ·················· 1-3
1-2.
SELF-DIAGNOSIS FUNCTION ···································· 1-4
1.
SELF-DIAGNOSIS FUNCTION ···································· 1-4
2.
SELF-DIAGNOSIS DISPLAY ······································· 1-4
3.
SELF-DIAGNOSIS CODE TABLE ································ 1-5
2.
DISASSEMBLY
2-1.
LCD CABINET (R) ASSEMBLY ··································· 2-2
2-2.
CABINET (F) SECTION ················································ 2-3
2-3.
CABINET (REAR) SECTION ······································· 2-3
2-4.
CONTROL SWITCH BLOCK (PS5000) ······················· 2-4
2-5.
CABINET (R) SECTION ··············································· 2-4
2-6.
TRIPOD SCREW ···························································· 2-5
2-7.
BJ-005 BOARD ······························································· 2-5
2-8.
BT-021 BOARD, LITHIUM BATTERY
(SECONDARY) ······························································ 2-6
(SECONDARY) ······························································ 2-6
2-9.
LOUD SPEAKER (1.6CM), FP-704 BOARD, MEMORY
STICK CONNECTOR ···················································· 2-7
STICK CONNECTOR ···················································· 2-7
2-10. HINGE BLIND ASSEMBLY ·········································· 2-8
2-11. LCD UNIT ······································································ 2-8
2-12. PD-198 BOARD ······························································ 2-9
2-13. HINGE ASSEMBLY ····················································· 2-10
2-14. EVF SECTION ······························································ 2-11
2-15. VF-158 BOARD ···························································· 2-12
2-16. STROBOSCOPE SECTION ········································· 2-13
2-17. FP-707 BOARD ···························································· 2-13
2-18. MIC UNIT (MIC5000) ·················································· 2-14
2-19. STROBOSCOPE LUMINOUS UNIT (ST5000),
2-11. LCD UNIT ······································································ 2-8
2-12. PD-198 BOARD ······························································ 2-9
2-13. HINGE ASSEMBLY ····················································· 2-10
2-14. EVF SECTION ······························································ 2-11
2-15. VF-158 BOARD ···························································· 2-12
2-16. STROBOSCOPE SECTION ········································· 2-13
2-17. FP-707 BOARD ···························································· 2-13
2-18. MIC UNIT (MIC5000) ·················································· 2-14
2-19. STROBOSCOPE LUMINOUS UNIT (ST5000),
STROBOSCOPE ASSEMBLY ····································· 2-14
2-20. LENS SECTION ··························································· 2-15
2-21. FP-706 BOARD - (1) ···················································· 2-15
2-22. FP-706 BOARD - (2) ···················································· 2-16
2-23. CD-452 BOARD, LENS DEVICE LSV-870A ············· 2-17
2-24. GMR (M) SENSOR ······················································ 2-17
2-25. IRIS (IR870), STEPPING MOTOR Z870A ·················· 2-18
2-26. VC-325 BOARD ··························································· 2-19
2-27. MECHANISM DECK ··················································· 2-19
2-28. AV-081 BOARD ···························································· 2-20
2-29. JK-257 BOARD ····························································· 2-20
2-30. CONTROL SWITCH BLOCK (FK5000) ····················· 2-22
2-31. CABINET (L) ASSEMBLY ·········································· 2-22
2-32. CABINET (G) ASSEMBLY ········································· 2-23
2-33. CIRCUIT BOARDS LOCATION ································· 2-24
2-34. FLEXIBLE BOARDS LOCATION ······························ 2-25
HELP (List of caution points is shown here.)
2-21. FP-706 BOARD - (1) ···················································· 2-15
2-22. FP-706 BOARD - (2) ···················································· 2-16
2-23. CD-452 BOARD, LENS DEVICE LSV-870A ············· 2-17
2-24. GMR (M) SENSOR ······················································ 2-17
2-25. IRIS (IR870), STEPPING MOTOR Z870A ·················· 2-18
2-26. VC-325 BOARD ··························································· 2-19
2-27. MECHANISM DECK ··················································· 2-19
2-28. AV-081 BOARD ···························································· 2-20
2-29. JK-257 BOARD ····························································· 2-20
2-30. CONTROL SWITCH BLOCK (FK5000) ····················· 2-22
2-31. CABINET (L) ASSEMBLY ·········································· 2-22
2-32. CABINET (G) ASSEMBLY ········································· 2-23
2-33. CIRCUIT BOARDS LOCATION ································· 2-24
2-34. FLEXIBLE BOARDS LOCATION ······························ 2-25
HELP (List of caution points is shown here.)
3.
BLOCK DIAGRAMS
3-1.
OVERALL BLOCK DIAGRAM (1/4) ··························· 3-1
3-2.
OVERALL BLOCK DIAGRAM (2/4) ··························· 3-3
3-3.
OVERALL BLOCK DIAGRAM (3/4) ··························· 3-5
3-4.
OVERALL BLOCK DIAGRAM (4/4) ··························· 3-7
3-5.
POWER BLOCK DIAGRAM (1/2) ································ 3-9
3-6.
POWER BLOCK DIAGRAM (2/2) ······························ 3-11
4.
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
SCHEMATIC DIAGRAMS
4-1.
FRAME SCHEMATIC DIAGRAM (1/4) ······················· 4-1
FRAME SCHEMATIC DIAGRAM (2/4) ······················· 4-3
FRAME SCHEMATIC DIAGRAM (3/4) ······················· 4-5
FRAME SCHEMATIC DIAGRAM (4/4) ······················· 4-7
FRAME SCHEMATIC DIAGRAM (3/4) ······················· 4-5
FRAME SCHEMATIC DIAGRAM (4/4) ······················· 4-7
4-2.
SCHEMATIC DIAGRAMS
Schematic diagram of the CD-452, VC-325 and
BT-021 board are not shown.
Pages from 4-11 to 4-48 are not shown.
BT-021 board are not shown.
Pages from 4-11 to 4-48 are not shown.
• BJ-005/FP-705 FLEXIBLE (DC/USB/DV JACK,
PANEL SWITCH)
SCHEMATIC DIAGRAM ···························· 4-49
• PD-198 (RGB DRIVE, BACKLIGHT DRIVE)
SCHEMATIC DIAGRAM ···························· 4-51
• VF-158 (1/3) (RGB DRIVE, TIMING GENERATOR,
BACK LIGHT)
SCHEMATIC DIAGRAM ···························· 4-53
• VF-158 (2/3) (MIC AMP)
SCHEMATIC DIAGRAM ···························· 4-55
• VF-158 (3/3) (CONNECTOR, PITCH/YAW SENSOR
AMP)
SCHEMATIC DIAGRAM ···························· 4-57
• AV-081/JK-257 (AV MULTI/HP/LANC/MIC JACK)
SCHEMATIC DIAGRAM ···························· 4-59
• FP-704 FLEXIBLE (MS CONNECTOR)
SCHEMATIC DIAGRAM ···························· 4-61
• FP-706 FLEXIBLE (REMOCON SENSOR, MF SW)
SCHEMATIC DIAGRAM ···························· 4-63
• FP-702/FP-707 FLEXIBLE (FLASH DRIVE)
SCHEMATIC DIAGRAM ···························· 4-65
• FLASH UNIT (ST5000)
SCHEMATIC DIAGRAM ···························· 4-67
• FP-467/468/228 FLEXIBLE (MD BLOCK)
SCHEMATIC DIAGRAM ···························· 4-69
• CONTROL SWITCH BLOCK (FK5000)
SCHEMATIC DIAGRAM ···························· 4-71
• CONTROL SWITCH BLOCK (PS5000)
SCHEMATIC DIAGRAM ···························· 4-73
4-3.
PRINTED WIRING BOARDS
Printed wiring board of the CD-452, VC-325
and BT-021 board are not shown.
Pages from 4-75 to 4-82 are not shown.
and BT-021 board are not shown.
Pages from 4-75 to 4-82 are not shown.
• BJ-005 (DC/USB/DV JACK)
PRINTED WIRING BOARD ······················· 4-83
• FP-705 FLEXIBLE (PANEL SWITCH)
PRINTED WIRING BOARD ······················· 4-85
• PD-198 (RGB DRIVE, BACK LIGHT DRIVE)
PRINTED WIRING BOARD ······················· 4-85
• AV-081 (AV MULTI)
PRINTED WIRING BOARD ······················· 4-87
• JK-257 (HP/LANC/MIC JACK)
PRINTED WIRING BOARD ······················· 4-87
• VF-158 (RGB DRIVE, TIMING GENERATOR, BACK
LIGHT, MIC AMP, CONNECTOR, PITCH/YAW
SENSOR AMP)
SENSOR AMP)
PRINTED WIRING BOARD ······················· 4-89
• FP-704 FLEXIBLE (MS CONNECTOR)
PRINTED WIRING BOARD ······················· 4-91
• FP-707 FLEXIBLE (FLASH DRIVE)
PRINTED WIRING BOARD ······················· 4-92
• FP-706 FLEXIBLE (REMOCON SENSOR, MF SW)
PRINTED WIRING BOARD ······················· 4-93
• FP-467/468/228 FLEXIBLE (MD BLOCK)
PRINTED WIRING BOARD ······················· 4-95
— 6 —
DCR-PC330/PC330E
4-4.
WAVEFORMS ······························································ 4-99
Waveforms of the CD-452 and VC-325 board are not
shown.
Pages 4-97 to 4-98 are not shown.
shown.
Pages 4-97 to 4-98 are not shown.
4-5.
MOUNTED PARTS LOCATION ······························· 4-104
Mounted parts location of the
CD-452, VC-325
and BT-021
board are not shown.
Page 4-101 to 4-103 is not shown.
5.
REPAIR PARTS LIST
5-1-1. OVERALL ······································································ 5-3
5-1-2. CABINET (R) SECTION-1 ············································ 5-4
5-1-3. CABINET (R) SECTION-2 ············································ 5-5
5-1-4. CABINET (L) SECTION-1 ············································ 5-6
5-1-5. CABINET (L) SECTION-2 ············································ 5-7
5-1-6. EVF SECTION ································································ 5-8
5-1-7. STROBOSCOPE SECTION ··········································· 5-9
5-1-8. LENS SECTION ··························································· 5-10
5-1-9. OVERALL (MECHANISM DECK-Z101) ···················· 5-11
5-1-10. LS CHASSIS BLOCK ASSEMBLY ·························· 5-12
5-1-11. MECHANICAL CHASSIS BLOCK ASSEMBLY ···· 5-13
5-2.
5-1-2. CABINET (R) SECTION-1 ············································ 5-4
5-1-3. CABINET (R) SECTION-2 ············································ 5-5
5-1-4. CABINET (L) SECTION-1 ············································ 5-6
5-1-5. CABINET (L) SECTION-2 ············································ 5-7
5-1-6. EVF SECTION ································································ 5-8
5-1-7. STROBOSCOPE SECTION ··········································· 5-9
5-1-8. LENS SECTION ··························································· 5-10
5-1-9. OVERALL (MECHANISM DECK-Z101) ···················· 5-11
5-1-10. LS CHASSIS BLOCK ASSEMBLY ·························· 5-12
5-1-11. MECHANICAL CHASSIS BLOCK ASSEMBLY ···· 5-13
5-2.
ELECTRICAL PARTS LIST ········································ 5-14
Parts list of the
BT-021, CD-452 and VC-325
board are not shown.
Pages from 5-18 to 5-27 are not shown.
Pages from 5-18 to 5-27 are not shown.
1-1
SECTION 1
SERVICE NOTE
DCR-PC330/PC330E
COVER
COVER
1-1. SERVICE NOTE
1.
POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off so
that the unit cannot operate.
This following two methods are available to prevent this. Take note of which to use during repairs.
that the unit cannot operate.
This following two methods are available to prevent this. Take note of which to use during repairs.
Method 1.
Use the AC power adaptor (AC-L15, AC-VQ800 etc.).
Use the AC power adaptor (AC-L15, AC-VQ800 etc.).
Method 2.
Connect the servicing remote commander RM-95 (J-6082-053-B) to the LANC jack, and set the commander switch to the “ADJ” side.
Connect the servicing remote commander RM-95 (J-6082-053-B) to the LANC jack, and set the commander switch to the “ADJ” side.
2.
TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)
1
Open the flash. (When the flash doesn’t open, refer to “3. HOW TO OPEN THE FLASH WHEN THE FLASH DOSEN’T OPEN”.)
2
Refer to page 2-3 to remove the cabinet (F) section.
3
Refer to page 2-3 to remove the cabinet (Rear) section.
4
Refer to page2-4 to remove the cabinet (R) section.
5
Refer to page2-11 to remove the EVF section.
6
Refer to page2-13 to remove the stroboscope section.
7
Refer to page2-15 to remove the lens section.
8
Open the VC-325 board.
9
Refer to page 2-19 to remove the VC-325 board and the mechanism deck.
q;
Disconnect CN2502 (27P, 0.3mm) of VC-325 board.
qa
Supply +4.5V from the DC power supply to the loading motor and unload with a pressing the cassette compartment.
3.
HOW TO OPEN THE FLASH WHEN THE FLASH DOSEN’T OPEN
Disconnect the flexible board from
CN2502 of VC-325 board.
CN2502 of VC-325 board.
Loading motor
VC-325 board
CN2502
DC power supply
(+ 4.5Vdc)
(+ 4.5Vdc)
1-2
DCR-PC330/PC330E
4.
DISCHARGING OF THE FLASHLIGHT POWER SUPPLY CAPACITOR
The power supply capacitor (C4208) of the FP-707 flexible is charged up to the maximum 300V potential.
There is a danger of electric shock by this high voltage when the capacitor is handled by hand. The electric shock is caused by the charged
voltage which is kept without discharging when the main power of the unit is simply turned off. Therefore, the remaining voltage must be
discharged as described below.
There is a danger of electric shock by this high voltage when the capacitor is handled by hand. The electric shock is caused by the charged
voltage which is kept without discharging when the main power of the unit is simply turned off. Therefore, the remaining voltage must be
discharged as described below.
4-1.
PREPARING THE SHORT JIG
To preparing the short jig. a small clip is attached to each end of a resistor of 1k
Ω
/1W (1-215-869-119)
Wrap insulating tape fully around the reads of the resistor to prevent electric shock.
4-2.
DISCHARGING THE CAPACITOR
1
Open the flash. (When the flash doesn’t open, refer to “3. HOW TO OPEN THE FLASH WHEN THE FLASH DOSEN’T OPEN”.)
2
Refer to page 2-3 to remove the cabinet (F) section.
3
Refer to page 2-3 to remove the cabinet (Rear) section.
4
Refer to page 2-4 to remove the cabinet (R) section.
5
Refer to page 2-11 to remove the EVF section.
6
Refer to page 2-13 to remove the stroboscope section.
7
Remove the insulation sheet of the capacitor (C4208) of the FP-707 flexible.
8
Short-circuit between (+) and (–) terminal of the capacitor (C4208) with the short jig about 10 seconds.
1 k
Ω
/1 W
Wrap insulating tape.
Short jig
C4208
Click on the first or last page to see other DCR-PC330 / DCR-PC330E (serv.man2) service manuals if exist.