DOWNLOAD Sony DCR-PC330 / DCR-PC330E (serv.man2) Service Manual ↓ Size: 5.13 MB | Pages: 96 in PDF or view online for FREE

2-14

3

1

 Two screws

     (M1.7 

×

 1.8)

2

 Two screws 

     (M1.7 

×

 2.5),

     lock ace, p2 (silver)

4

 Two tapping screws

     (M1.7 

×

 3.5) (silver)

5

 Two screws

     (M1.7 

×

 2.5) (silver)

qa

 Microphone

     cushion

7

 Hot shoe frame

6

 Claw

8

 FP-701 flexible

     board (10P)

q;

 Cabinet (upper)

qs

 MIC unit

     (MIC5000)

9

 External connector

     (hot shoe)

1

 Two tapping screws 

     (M1.7 

×

 5) (black)

2

 Claw

3

 Stroboscope

     cabinet

4

 Two

     claws

5

 Unit cover

     assembly

6

 Screw (M1.7 

×

 2.5),

     lock ace, p2 (silver)

7

 Screw (bolt)

     (M1.4 

×

 3)

8

 Stroboscope luminous

     unit (ST5000)

switch

When re-assembling, 
confirm the switch position.

qs

 Stroboscope

     assembly

9

 Three claws

q;

 Blind cabinet

qa

 Two cushions

     (stroboscope)

2-15

VC-
325

1

 CD-452 board

     (80P)

4

 FP-706 board (18P)

2

 Tape (A)

Tape (A)

3

 Flexible board

     (from lens device)(33P)

5

 Screw

     (M1.7 

×

 2.5),

     lock ace, p2(silver)

6

 Lens section

When re-assembling, 
attach the tape (A) as shown. 

1

 Tapping screw 

     (M1.7 

×

 5) (silver)

2

 Tapping screw 

     (M1.7 

×

 5) (silver)

5

 MF ring assembly,

     FP-706 board

3

 Remove the

     four dowels and
     convex part

4

 Lens device LSV-870A,

     CD-452 board, etc.

2-16

7

1

 Two

     claws

2

 Screw (M1.7 

×

 2.5),

     lock ace, p2 (silver)

3

 Tapping screw

     (M1.7 

×

 3.5) (silver)

4

 IR frame

FP-706 board

5

 Screw (M1.7 

×

 2.5),

     lock ace, p2 (silver)

6

 MF ring assembly

q;

 FP-706 board

When soldering the laser unit on the FP-706 board,
observe the following things.
(Refer to Service Note (page 1-3)).

Observe the following conditions of temperature
and time of soldering.
Temperature of soldering iron : 350

°

Time of contacting the soldering : 3 seconds
iron with the solder

The laser diode may suffer electrostatic breakdown
because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the
human body.
During repair, pay attention to electrostatic breakdown
and also use the procedure in the printed matter which
is included in the repair parts.

The flexible board is easily damaged and should be
handled with care.

9

 Laser unit

8

 Three solderings

2-17

1

 FK flexible

     fixed sheet

2

 CD shield

     sheet (A)

3

 Tapping screw

     (M1.7 

×

 5) (silver)

4

 CD heat sink,

     CD radiation sheet,
     MD flexible guard sheet, etc.

(CD heat sink)

(CD radiation sheet)

(CD radiation sheet (small))

(MD flexible guard sheet)

5

 CDF sheet

6

 BB retainer cushion (A)

7

 Two tapping screws

     (M1.7 

×

 5) (silver)

8

 Lens device LSV-870A

9

 Optical filter block

     (OFB-04-30)

q;

 Seal rubber (870)

qa

 Remove the

     solderings

qs

 CCD block

     assembly

qd

 CD-452

     board

CD radiation sheet
(L)(large)

1

 Screw (M1.4 

×

 3.5)

5

 Screw

     (M1.4 

×

 3.5)

4

 GMR (M) sensor

8

 GMR (M) sensor

2

 MR spacer (760)

6

 MR spacer (760)

3

 Remove the

     four solderings

7

 Remove the

     four solderings

Be careful not to drop 
the MR spacer (760).

Be careful not to drop 
the MR spacer (760).