DOWNLOAD Sony DCR-HC47E / DCR-HC48 / DCR-HC48E (serv.man4) Service Manual ↓ Size: 788.14 KB | Pages: 77 in PDF or view online for FREE

6-7

DCR-HC47E/HC48/HC48E_ADJ

H

A=B

C=D

A B

B

C

D

A

Enlargement

V

Electronic beam scanning frame

CRT picture frame

B

A

Difference in level

Y

ello

w

Cy

an

Green

White

Magenta

Red

Blue

Y

ello

w

Cy

an

Green

White

Magenta

Red

Blue

Fig. a
(VIDEO terminal of A/V OUT jack
output waveform)

Fig. b (monitor TV picture)

Adjust the camera zoom and direction to
obtain the output waveform shown in Fig. a and
the monitor TV display shown in Fig. b.

Basically carry out adjustments in the order given.

1) Color bar chart (Color reproduction adjustment frame)

When performing adjustments using the color bar chart, ad-
just the picture frame as shown in Fig. 6-1-4. (Color reproduc-
tion adjustment frame)

2) Clear chart (AWB adjustment frame)

Shoot the color bar chart. Then adjust the zoom to TELE side
from WIDE side, and stop it when the black frame of the chart
disappears. Remove the color bar chart from pattern box and
insert a clear chart in its place.

3) Chart for flange back adjustment

Join together a piece of white A0 size paper (1189mm 

× 841

mm) and a piece of black paper to make the chart shown in
Fig. 6-1-5.

Note: Use a non-reflecting and non-glazing vellum paper. The

size must be A0 or larger and the joint between the white
and black paper must not have any undulations.

Black

White

841 mm

1189 mm

1. POWER switch (SS21200 block) ................ CAMERA-TAPE
2. NIGHTSHOT PLUS switch (Lens block) ...................... OFF
3. WIDE SELECT (Panel block) ............................................ 4:3
4. BACK LIGHT (CF102 board) ......................................... OFF
5. SCENE SELECT (MENU setting) .............................. AUTO
6. EXPOSURE (MENU setting) ...................................... AUTO
7. WHITE BAL. (MENU setting) .................................... AUTO

8. FOCUS (MENU setting) ....................................... MANUAL
9. COLOR SLOW S (MENU setting) ................................. OFF
10. DIGITAL ZOOM (MENU setting) ................................. OFF
11. STEADY SHOT (MENU setting) ................................... OFF
12. D EFFECT (MENU setting) ............................................ OFF
13. PICT. EFFECT (MENU setting) ..................................... OFF
14. DEMO MODE (MENU setting) ..................................... OFF

Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette.

6-8

DCR-HC47E/HC48/HC48E_ADJ

A dark room is required to provide an accurate flash adjustment.
If it is not available, prepare the flash adjustment box as given
below;

1) Provide woody board A, B and C of 15 mm thickness.

2) Apply black mat paint to one side of woody board A and B.
3) Attach background paper (J-2501-130-A) to woody board C.
4) Assemble so that the black sides and the background paper

side of woody board A, B and C are internal. (Fig. 6-1-7)

woody board A (2)

400 mm

woody board B (2)

370 mm

woody board C (1)

700 mm

513 mm

513 mm

700 mm

700 mm

730 mm

woody board A

woody board B

woody board B

woody board C

woody board A

6-9

DCR-HC47E/HC48/HC48E_ADJ

Order Page Address Data

Procedure

1

0

01

01

2

0

10

00

3

7

04

Set the following data

30: NTSC model
31: PAL model

Set the following data

20: Initializing A page
21: Initializing B page
22: Initializing D page
23: Initializing 1A page
24: Initializing 1B page

4

7

01

25: Initializing A and 1A

page

26: Initializing B and 1B

page

28: Initializing A, B, D, 1A

and 1B page

5

7

00

01

Press PAUSE (Write) button.

6

7

02

Check the data changes to
“01”.

7

Perform “Modification of A,
B, D, 1A, 1B Page Data”

Note 2: NTSC model: DCR-HC48

PAL model: DCR-HC47E/HC48E

Note 1: Pages used for the EVR consists of 22 pages. There are

8, A to D, 18, 1A to 1C, 63 to 6F pages.

Note 2: When reading or writing the 18, 1A, 1B or 1C page data,

select page: 0, address: 10, and set data: 01, then select
8, A, B or C page. The 18, 1A, 1B or 1C page can be
chosen by this data setting.
After reading or writing, reset the data or page: 0, ad-
dress: 10 to “00”.

Note 3: When reading or writing the 63 to 6F page data, select

page: 0, address: 10, and set data: 06, then select 3, 4, 5,
6, 7, 8, 9, A, B, C, D, E, or F page. The 63, 64, 65, 66, 67,
68, 69, 6A, 6B, 6C, 6D, 6E, or 6F page can be chosen by
this data setting.
After reading or writing, reste the data of page: 0, ad-
dress: 10 to “00”.

Note: Check that the data of page: 0, address: 10 is “00”.

Note 1: If the A, B, D, 1A, 1B page data has been initialized, the

following adjustments need to be performed again.
1) Modification of A, B, D, 1A, 1B page data
2) Touch panel adjustment

Adjustment Page

A

Adjustment Address

10 to FF

Adjustment Page

B

Adjustment Address

00 to FF

Adjustment Page

D

Adjustment Address

10 to 7F

Adjustment Page

1A

Adjustment Address

00 to FF

Adjustment Page

1B

Adjustment Address

00 to FF

6-10

DCR-HC47E/HC48/HC48E_ADJ

Note 1: Check that the data of page: 0, address: 10 is“00”.
Note 2: Fixed data-1: Initialized data. (Refer to“1. Initializing of

A, B, D, 1A, 1B Page Data”)
Fixed data-2: Modified data. (Refer to“2. Modification
of A, B, D, 1A, 1B Page Data”)

Address

Initial value

Remark

NTSC PAL

10

00

00

Test mode

11 to 17

Fixed data-1 (Initialized data)

18

Fixed data-2

19

Fixed data-1 (Initialized data)

1A

Fixed data-2

1B to 2E

Fixed data-1 (Initialized data)

2F

Fixed data-2

30

Fixed data-1 (Initialized data)

31

32

Fixed data-2

33 to 5F

Fixed data-1 (Initialized data)

60

61

62

Fixed data-2

63

64 to 8F

Fixed data-1 (Initialized data)

90

F0

F3

91

0F

0B

Touch panel adj.

92

E6

DB

93

10

22

94 to EF

Fixed data-1 (Initialized data)

F0

F1

Fixed data-2

F2

F3 to FF

Fixed data-1 (Initialized data)

If the A, B, D, 1A, 1B page data has been initialized, change the
data of the “Fixed data-2” address shown in the following table by
manual input.

Modifying Method:
1) Before changing the data, select page: 0, address: 01, and set

data: 01.

2) If modification of data on pages A, B, D, set data: 00 to page:

0, address: 10, and then select pages A, B, D.

3) If modification of data on pages 1A, 1B, set data: 01 to page:

0, address: 10, and then select pages A, B.
After the modification of data finished, return the data on page:
0, address: 10 to “00”.

4) New data for changing are not shown in the tables because

they are different in destination. When changing the data, copy
the data built in the same model.
Note 1: If copy the data built in the different model, the

camcorder may not operate.

5) When changing the data, press the PAUSE (Write) button of

the adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.

6) Check that the data of adjustment addresses is the initial value.

If not, change the data to the initial value.

Order Page Address Data

Procedure

1

0

10

00

2

2

00

29

3

2

01

29

Press PAUSE (Write) button.

Note 2: If following symptoms occur after completing of the

“Modification A, B, D, 1A, 1B page data”, check that
the data of the “Fixed data-2” address of A, B, D, 1A, 1B
page are same as those of same model of same destina-
tion.
1) The power is shut off so that unit cannot operate.