DOWNLOAD Sony DCR-HC47E / DCR-HC48 / DCR-HC48E (serv.man4) Service Manual ↓ Size: 788.14 KB | Pages: 77 in PDF or view online for FREE

6-31

DCR-HC47E/HC48/HC48E_ADJ

Order Page Address Data

Procedure

1

Check that the picture frame
is “Color Reproduction
Adjustment Frame”. If not,
perform “6. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”

2

0

01

01

3

6

02

Check the data change to
“01”.

4

6

D0

Set the following data, and
press PAUSE (Write) button.

7C: NTSC model
82: PAL model

5

6

01

3D

Press PAUSE (Write) button.

6

0

10

06

7

6

00

Set the following data, and
press PAUSE (Write) button.

77: NTSC model
F7: PAL model

8

Adjust the GAIN and
PHASE of the vectorscope,
and set to the burst lumi-
nance point to the burst
position of color reproduc-
tion frame.

9

F

Change the data and settle
each color luminance point in
each color reproduction
frame. (Note 5)

10

0

10

00

Note 4: If not, select page: 6, address: 01, set data: 00, and press

PAUSE (Write) button.

Note 5: Be sure to press the PAUSE (Write) button of the adjust-

ing remote commander before changing the addresses.
If not, the new data will not be written to the memory.

Order Page Address Data

Procedure

1

6

01

00

Press PAUSE (Write) button.

2

6

D0

00

3

0

01

00

4

Perform “Color Reproduc-
tion Check”.

11. Color Reproduction Adjustment
Adjust the color separation matrix coefficient so that proper color
reproduction is produced.

Subject

Color bar chart
(Color reproduction adjustment
frame)

Measurement Point

Video terminal of A/V OUT jack
(75 

Ω terminated)

Measuring Instrument

Vectorscope

Adjustment Page

6F

Adjustment Address

37, 39, 40, 41

Specified Value

All color luminance points should
settle within each color reproduction
frame.

Note 1: If reading/writing data on pages 66, 6F, set data: 06 to

page: 0, address: 10, and then select pages: 6, F. By this
data setting, the pages 66, 6F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.

Note 2: Perform “Hall Adjustment” and “Flange Back Adjust-

ment” before this adjustment.

Note 3: NTSC model: DCR-HC48

PAL model: DCR-HC47E/HC48E

Switch setting:
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) WIDE SELECT .................................................................. 4:3
4) DIGITAL ZOOM (Menu setting) .................................... OFF
5) STEADYSHOT (Menu setting) ...................................... OFF
6) FOCUS (Menu setting) .......................................... MANUAL

37
39
40
41

(66)

(6F)

6-32

DCR-HC47E/HC48/HC48E_ADJ

R-Y

B-Y

R

G

B

M

G

C

Y

Y

E

Burst
position

R-Y

B-Y

R

G

B

M

G

C

Y

Y

E

Burst
position

6-33

DCR-HC47E/HC48/HC48E_ADJ

Subject

Color bar chart (Color reproduction
adjustment frame)

Measurement Point

Video terminal of A/V OUT jack
(75 

Ω terminated)

Measuring Instrument

Vectorscope

Adjusting
remote
commander

Specified Value

All color

Data of page: 6,

luminance

address: 0C is

points should

“00”

settle within each
color
reproduction
frame.

Note 1: Perform “Color Reproduction Adjustment” before this

adjustment.

Note 2: Perform this along with the “Color Reproduction Adjust-

ment” successively.

Note 3: Check that the data of page: 0, address: 10 is “00”.
Note 4: NTSC model: DCR-HC48

PAL model: DCR-HC47E/HC48E

Switch setting
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) WIDE SELECT .................................................................. 4:3
4) DIGITAL ZOOM (Menu setting) .................................... OFF
5) STEADY SHOT (Menu setting) ..................................... OFF
6) FOCUS (Menu setting) .......................................... MANUAL

Order Page Address Data

Procedure

1

Check that the picture frame
is “Color Reproduction
Adjustment Frame”. If not,
perform “6. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”

2

0

01

01

3

6

02

Check the data is “00”.
(Note 5)

4

6

D0

Set the following data, and
press PAUSE (Write) button
 7C: NTSC model
 82: PAL model

5

6

01

4D

Press PAUSE (Write) button.
(Note 6)

6

6

02

Check the data changes to
“01”.

7

6

0C

Check the data is “00”.

Note 5: If not, select page: 6, address: 01, set data: 00, and press

PAUSE (Write) button.

Note 6: Confirm that the Y signal level (A) is 90

±5 IRE.

(Refer to Fig 6-1-16)
90

±5 IRE = 606.9 to 678.3 mV (NTSC)

90

±5 IRE = 595 to 665 mV (PAL)

Order Page Address Data

Procedure

1

6

01

00

Press PAUSE (Write) button.

2

6

D0

00

3

0

01

00

A

White

6-34

DCR-HC47E/HC48/HC48E_ADJ

How to reset the zoom and focus when they deviated:
If the zoom and focus deviated due to some reason, reset them in
the following method.

Order Page Address Data

Procedure

1

6

90

XL

2

6

91

XH

3

6

92

YL

4

6

93

YH

5

6

01

79

Press PAUSE (Write) button

Processing after Completing Adjustment:
Reset the data setting after the adjustment finished.

Order Page Address Data

Procedure

1

6

01

00

Press PAUSE (Write) button.

2

6

90

00

3

6

91

00

4

6

92

00

5

6

93

00

Subject

Clear chart (AWB Adjustment frame)
(1 m (PTB-450) or 40 cm (PTB-1450)
from the front of lens)

Measurement Point

Video terminal of  A/V OUT jack
(75 

Ω terminated)

Measuring Instrument

Monitor TV

Specified Value

Only the clear chart must be shot
(entire screen is white).

Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: The right four digits of the page: 1 displayed data of the

adjusting remote commander.

1:XX : XX

XL or YL data
XH or YH data

Switch setting
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) WIDE SELECT .................................................................. 4:3
4) DIGITAL ZOOM (Menu setting) .................................... OFF
5) STEADY SHOT (Menu setting) ..................................... OFF
6) FOCUS ................................................................... MANUAL

Order Page Address Data

Procedure

1

Perform “7. Picture Frame
Setting (Color reproduction
adjustment frame)”.

2

By zooming in the color
reproduction adjustment
picture frame, set up the
picture frame in which the
color bar is shot on full
screen. (Refer to Fig. 6-1-17)

3

Remove the Color bar chart
from the pattern box.

4

Check that whole of the
screen is white.

5

0

03

18

6

1

Read XH data and XL data.
(Note 2)

7

0

03

22

8

1

Read YH data and YL data.
(Note 2)

9

0

03

00

10

In the following adjustment, if
the “AWB Adjustment frame”
is used, adjust the clear chart
to this position.

Color bar chart picture frame

Monitor TV picture frame