Sony DCR-HC47E / DCR-HC48 / DCR-HC48E (serv.man4) Service Manual ▷ View online
6-27
DCR-HC47E/HC48/HC48E_ADJ
6.
Picture Frame Setting (Center frame)
Subject
Clear chart (Center frame)
(1 m (PTB-450) or 40 cm (PTB-
1450) from the front of lens)
(1 m (PTB-450) or 40 cm (PTB-
1450) from the front of lens)
Measurement Point
Video terminal of A/V OUT jack
(75
(75
Ω terminated)
Measuring Instrument
Monitor TV
Specified Value
Whole of the screen is white
Note: If reading/writing data on pages 6A, set data: 06 to page: 0,
address: 10, and then select pages A. By this data setting,
the pages 6A can be selected.
After the data reading/writing finished, return the data on
page: 0, address: 10 to “00”.
the pages 6A can be selected.
After the data reading/writing finished, return the data on
page: 0, address: 10 to “00”.
Switch setting
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) WIDE SELECT .................................................................. 4:3
4) ZOOM .................................................................... WIDE end
5) DIGITAL ZOOM (Menu setting) .................................... OFF
6) STEADY SHOT (Menu setting) ..................................... OFF
7) FOCUS (Menu Setting) ......................................... MANUAL
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) WIDE SELECT .................................................................. 4:3
4) ZOOM .................................................................... WIDE end
5) DIGITAL ZOOM (Menu setting) .................................... OFF
6) STEADY SHOT (Menu setting) ..................................... OFF
7) FOCUS (Menu Setting) ......................................... MANUAL
Setting method:
Order Page Address Data
Procedure
1
Shoot a clear chart in the
center of screen with the
zoom at WIDE end.
center of screen with the
zoom at WIDE end.
2
0
01
01
3
0
10
06
A
4
(6A)
11
91
Press PAUSE (Write) button.
5
Check with the zoom at
WIDE end that the clear
chart is shot larger than the
size shown in the figure.
(Fig. 6-1-14)
WIDE end that the clear
chart is shot larger than the
size shown in the figure.
(Fig. 6-1-14)
A
6
(6A)
11
00
Press PAUSE (Write) button.
7
0
10
00
8
0
01
00
9
In the following adjustment,
if the “Center frame” is used,
adjust the clear chart to this
position.
if the “Center frame” is used,
adjust the clear chart to this
position.
With the zoom at WIDE end, shoot the clear
chart larger than this size.
Fig.6-1-11
6-28
DCR-HC47E/HC48/HC48E_ADJ
7.
F No. & ND Light Quality Standard Data Input
RadarW
RadarW
RadarW
Correct the lens iris and dispersion of the ND filter light quantity.
Adjustment Page
6F
Adjustment Address
1C to 23
Note 1: If reading/writing data on pages 6F, set data: 06 to page:
0, address: 10, and then select pages: F. By this data set-
ting, the pages 6F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
ting, the pages 6F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 0, address: 10, and set data: 06.
3) Input the following data to page: 6F, address: 1C to 23.
Note 2: Press the PAUSE (Write) button of the adjustment re-
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 0, address: 10, and set data: 06.
3) Input the following data to page: 6F, address: 1C to 23.
Note 2: Press the PAUSE (Write) button of the adjustment re-
mote commander each time to set data.
Address Data
1C
F5
1D
F4
1E
F8
1F
FB
20
FA
21
FD
22
F5
23
F4
4) Select page: 0, address: 10, and set data: 00.
5) Select page: 0, address: 01, and set data: 00.
5) Select page: 0, address: 01, and set data: 00.
8.
MAX GAIN Adjustment
RadarW
RadarW
RadarW
Setting the minimum illumination.
If it is not consistent, the image level required for taking subjects
in low illuminance will not be produced (dark).
If it is not consistent, the image level required for taking subjects
in low illuminance will not be produced (dark).
Subject
Clear chart (Center frame)
(40 cm (PTB-1450) from the front of
lens)
(40 cm (PTB-1450) from the front of
lens)
Adjustment Page
6F
Adjustment Address
2C
Note 1: Perform “Flange Back Adjustment” before this adjust-
ment.
Note 2: Check that the data of page: 0, address: 10 is “00”.
Note 3: NTSC model: DCR-HC48
Note 3: NTSC model: DCR-HC48
PAL model: DCR-HC47E/HC48E
Switch setting
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) WIDE SELECT .................................................................. 4:3
4) ZOOM .................................................................... WIDE end
5) DIGITAL ZOOM (Menu setting) .................................... OFF
6) STEADY SHOT (Menu setting) ..................................... OFF
7) FOCUS (Menu setting) .......................................... MANUAL
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) WIDE SELECT .................................................................. 4:3
4) ZOOM .................................................................... WIDE end
5) DIGITAL ZOOM (Menu setting) .................................... OFF
6) STEADY SHOT (Menu setting) ..................................... OFF
7) FOCUS (Menu setting) .......................................... MANUAL
Adjusting method:
Order Page Address Data
Procedure
1
Check that the picture frame
is “Center Frame”. If not,
perform “6. Picture Frame
Setting (Center Frame)”
is “Center Frame”. If not,
perform “6. Picture Frame
Setting (Center Frame)”
2
0
01
01
3
6
02
Check the data is “00”.
(Note 4)
(Note 4)
4
6
D0
20
5
6
D1
Set the following data.
80: NTSC model
B0: PAL model
B0: PAL model
6
6
01
6F
Press PAUSE (Write) button.
(Note 5)
(Note 5)
7
6
02
Check the data changes to
“01”.
“01”.
Note 4: If not, select page: 6, address: 01, set data: 00, and press
PAUSE (Write) button.
Note 5: The adjustment data will be automatically input to page:
6F, address: 2C.
Processing after Completing Adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE (Write) button.
2
0
01
00
6-29
DCR-HC47E/HC48/HC48E_ADJ
9.
Mechanical Shutter Adjustment
RadarW
RadarW
RadarW
Adjust the close time and loss time every F number of the me-
chanical shutter and the high-speed shutter correction value to
correct the luminous exposure.
chanical shutter and the high-speed shutter correction value to
correct the luminous exposure.
Adjustment Page
6F
Adjustment Address
76 to 8B
Note 1: If reading/writing data on pages 6F, set data: 06 to page:
0, address: 10, and then select pages: F. By this data set-
ting, the pages 6F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
ting, the pages 6F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
Note 2: NTSC model: DCR-HC48
PAL model: DCR-HC47E/HC48E
Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 0, address: 10, and set data: 06.
3) Input the following data to page: 6F, address: 76 to 8B.
Note 3: Press the PAUSE (Write) button of the adjustment re-
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 0, address: 10, and set data: 06.
3) Input the following data to page: 6F, address: 76 to 8B.
Note 3: Press the PAUSE (Write) button of the adjustment re-
mote commander each time to set data.
Address
Data
NTSC
PAL
76
5B
4A
77
8F
86
78
47
39
79
87
BC
7A
3E
31
7B
1E
F3
7C
37
2C
7D
F8
E6
7E
32
28
7F
5D
A1
80
6A
76
81
81
84
82
8A
8E
83
88
8D
84
75
7D
85
24
22
86
84
82
87
80
80
88
80
80
89
80
80
8A
80
80
8B
82
80
4) Select page: 0, address: 10, and set data: 00.
5) Select page: 0, address: 01, and set data: 00.
5) Select page: 0, address: 01, and set data: 00.
6-30
DCR-HC47E/HC48/HC48E_ADJ
10. Picture Frame Setting
(Color reproduction adjustment frame)
Subject
Color bar chart
(Color reproduction adjustment
frame)
(1 m (PTB-450) or 40 cm (PTB-
1450) from the front of lens)
(Color reproduction adjustment
frame)
(1 m (PTB-450) or 40 cm (PTB-
1450) from the front of lens)
Measurement Point
Video terminal of A/V OUT jack
(75
(75
Ω terminated)
Measuring Instrument
Oscilloscope and monitor TV
Specified Value
A=B, C=D, E=F
Note 1: Perform “Hall Adjustment” and “Flange Back Adjust-
ment” before this adjustment.
Note 2: Check that the data of page: 0, address: 10 is “00”.
Switch setting
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) WIDE SELECT .................................................................. 4:3
4) DIGITAL ZOOM (Menu setting) .................................... OFF
5) STEADY SHOT (Menu setting) ..................................... OFF
6) FOCUS (Menu Setting) ......................................... MANUAL
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) WIDE SELECT .................................................................. 4:3
4) DIGITAL ZOOM (Menu setting) .................................... OFF
5) STEADY SHOT (Menu setting) ..................................... OFF
6) FOCUS (Menu Setting) ......................................... MANUAL
Setting method:
Order
Procedure
1
Adjust the zoom and the camera direction, and set
the specified position.
the specified position.
2
Mark the position of the picture frame on the monitor
TV, and adjust the picture frame to the this position
in following adjustment using “Color reproduction
adjustment frame”.
TV, and adjust the picture frame to the this position
in following adjustment using “Color reproduction
adjustment frame”.
How to read the XH, XL, YH and YL data:
Order Page Address Data
Procedure
1
0
03
18
2
1
Read XH data and XL data.
(Note 3)
(Note 3)
3
0
03
22
4
1
Read YH data and YL data.
(Note 3)
(Note 3)
Note 3: The right four digits of the page: 1 displayed data of the
adjusting remote commander.
1:XX : XX
XL or YL data
XH or YH data
XH or YH data
How to reset the zoom and focus when they deviated:
If the zoom and focus deviated due to some reason, reset them in
the following method.
If the zoom and focus deviated due to some reason, reset them in
the following method.
Order Page Address Data
Procedure
1
6
90
XL
2
6
91
XH
3
6
92
YL
4
6
93
YH
5
6
01
79
Press PAUSE (Write) button.
Check on the oscilloscope
1. Horizontal period
Fig. 6-1-12
2. Vertical period
Fig. 6-1-13
Check on the monitor TV (Underscanned mode)
Fig. 6-1-14
A=B
C=D
A
B
C
D
E=F
V
E
F
Color bar chart picture frame
Monitor TV picture frame
How to release the picture frame setting:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE (Write) button.
2
6
90
00
3
6
91
00
4
6
92
00
5
6
93
00
Click on the first or last page to see other DCR-HC47E / DCR-HC48 / DCR-HC48E (serv.man4) service manuals if exist.