Sony DCR-HC43 (serv.man3) Service Manual ▷ View online
6-30
DCR-HC43
10. MAX GAIN Adjustment
RadarW
RadarW
RadarW
RadarW
RadarW
Setting the minimum illumination.
If it is not consistent, the image level required for taking subjects
in low illuminance will not be produced (dark).
If it is not consistent, the image level required for taking subjects
in low illuminance will not be produced (dark).
Subject
Clear chart (Center frame)
Adjustment Page
F
Adjustment Address
2C
Note 1:
Perform “Flange Back and Zoom Lever Center Adjust-
ment” before this adjustment.
ment” before this adjustment.
Note 2:
Check that the data of page: 0, address: 10 is “00”.
Note 3:
Check that the data of page: 6, address: 02 is “00”. If
not, select page: 6, address: 01, set data: 00, and press
PAUSE button.
not, select page: 6, address: 01, set data: 00, and press
PAUSE button.
Note 4:
NTSC model: DCR-HC41/HC42/HC43
PAL model: DCR-HC39E/HC42E/HC43E
PAL model: DCR-HC39E/HC42E/HC43E
Note 5:
If the pattern box (PTB-450) is used, the stability of
brightness is reduced, and thus the adjustment value will
be shifted a little.
The use of small pattern box (PTB-1450) is recom-
mended.
brightness is reduced, and thus the adjustment value will
be shifted a little.
The use of small pattern box (PTB-1450) is recom-
mended.
Switch setting
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) ZOOM .................................................................... WIDE end
4) DIGITAL ZOOM (Menu setting) .................................... OFF
5) STEADY SHOT (Menu setting) ..................................... OFF
6) FOCUS (Menu setting) .......................................... MANUAL
7) WIDE SELECT ................................................................ 4: 3
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) ZOOM .................................................................... WIDE end
4) DIGITAL ZOOM (Menu setting) .................................... OFF
5) STEADY SHOT (Menu setting) ..................................... OFF
6) FOCUS (Menu setting) .......................................... MANUAL
7) WIDE SELECT ................................................................ 4: 3
Adjusting method:
Order Page Address Data
Procedure
1
Check that the picture frame
is “Center Frame”. If not,
perform “8. Picture Frame
Setting (Center Frame)”
is “Center Frame”. If not,
perform “8. Picture Frame
Setting (Center Frame)”
2
0
01
01
3
6
D0
Set the following data.
24: NTSC model
21: PAL model
21: PAL model
4
6
D1
00
5
6
01
6F
Press PAUSE button. (Note 6)
6
6
02
Check the data changes to
“01”.
“01”.
Note 6:
The adjustment data will be automatically input to page:
F, address: 2C.
F, address: 2C.
Processing after Completing Adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE button.
2
0
01
00
11. Mechanical Shutter Adjustment
RadarW
RadarW
RadarW
Adjustment Page
F
Adjustment Address
76 to 8B
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Adjusting method:
1) Select page: 0, address: 01, and set data: 01.
2) Input the following data to page: F, address: 76 to 8B.
1) Select page: 0, address: 01, and set data: 01.
2) Input the following data to page: F, address: 76 to 8B.
Note:
Press the PAUSE button of the adjustment remote com-
mander each time to set data.
mander each time to set data.
Address
Data
76
50
77
93
78
3D
79
8D
7A
35
7B
99
7C
31
7D
83
7E
2D
7F
7B
80
60
81
73
82
77
83
72
84
60
85
1C
86
80
87
80
88
80
89
80
8A
80
8B
82
3) Select page: 0, address: 01, and set data: 00.
6-31
DCR-HC43
R-Y
B-Y
R
B
G
M
G
Y
E
C
Y
Burst
R-Y
B-Y
R
B
G
M
G
Y
E
C
Y
Burst
Fig. 6-1-15
NTSC model
PAL model
Processing after completing adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE button.
2
6
9D
00
3
0
01
00
12. Color Reproduction Adjustment
Adjust the color separation matrix coefficient so that proper color
reproduction is produced.
reproduction is produced.
Subject
Color bar chart
(Color reproduction adjustment
frame)
(Color reproduction adjustment
frame)
Measurement Point
Video terminal of A/V OUT jack or
A/V jack
(75
A/V jack
(75
Ω
terminated)
Measuring Instrument
Vectorscope
Adjustment Page
F
Adjustment Address
37, 39, 40, 41
Specified Value
All color luminance points should
settle within each color reproduction
frame.
settle within each color reproduction
frame.
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Note 2:
Perform “Flange Back Adjustment” before this adjust-
ment.
ment.
Note 3:
NTSC model: DCR-HC41/HC42/HC43
PAL model: DCR-HC39E/HC42E/HC43E
PAL model: DCR-HC39E/HC42E/HC43E
Switch setting:
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
5) FOCUS (Menu setting) .......................................... MANUAL
6) WIDE SELECT ................................................................. 4: 3
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADYSHOT (Menu setting) ...................................... OFF
5) FOCUS (Menu setting) .......................................... MANUAL
6) WIDE SELECT ................................................................. 4: 3
Adjusting method:
Order Page Address Data
Procedure
1
Check that the picture frame
is “Color Reproduction
Adjustment Frame”. If not,
perform “7. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”
is “Color Reproduction
Adjustment Frame”. If not,
perform “7. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”
2
0
01
01
3
6
9D
Set the following data.
27: NTSC model
22: PAL model
27: NTSC model
22: PAL model
4
6
01
3D
Press PAUSE button.
5
F
F0
Set the following data, and
press PAUSE button.
37: NTSC model
B7: PAL model
press PAUSE button.
37: NTSC model
B7: PAL model
6
Adjust the GAIN and
PHASE of the vectorscope,
and set to the burst lumi-
nance point to the burst
position of color reproduc-
tion frame.
PHASE of the vectorscope,
and set to the burst lumi-
nance point to the burst
position of color reproduc-
tion frame.
7
F
Change the data and settle
each color luminance point in
each color reproduction
frame. (Note 4)
each color luminance point in
each color reproduction
frame. (Note 4)
Note 4:
Be sure to press the PAUSE button of the adjusting re-
mote commander before changing the addresses. If not,
the new data will not be written to the memory.
mote commander before changing the addresses. If not,
the new data will not be written to the memory.
37
39
40
41
39
40
41
6-32
DCR-HC43
13. Color Reproduction Check
RadarW
RadarW
RadarW
RadarW
RadarW
Subject
Color bar chart (Color reproduction
adjustment frame)
adjustment frame)
Measurement Point
Video terminal of
Displayed data of
A/V OUT jack or
page: 1 (Note 4)
A/V jack
(75
(75
Ω
terminated)
Measuring Instrument
Vectorscope
Adjusting
remote
commander
remote
commander
Specified Value
All color
bit15 is “1”
luminance
points should
settle within each
color
reproduction
frame.
points should
settle within each
color
reproduction
frame.
Note 1:
Perform “Color Reproduction Adjustment” before this
adjustment.
adjustment.
Note 2:
Check that the data of page: 0, address: 10 is “00”.
Note 3:
Check that the data of page: 6, address: 02 is “00”. If
not, select page: 6, address: 01, set data: 00, and press
PAUSE button.
not, select page: 6, address: 01, set data: 00, and press
PAUSE button.
Note 4:
The right four digits of the page: 1 displayed data of the
adjusting remote commander.
adjusting remote commander.
1:XX:XX
Displayed data
Switch setting
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADY SHOT (Menu setting) ..................................... OFF
5) FOCUS (Menu setting) .......................................... MANUAL
6) WIDE SELECT ................................................................. 4: 3
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADY SHOT (Menu setting) ..................................... OFF
5) FOCUS (Menu setting) .......................................... MANUAL
6) WIDE SELECT ................................................................. 4: 3
Adjusting method:
Order Page Address Data
Procedure
1
Check that the picture frame
is “Color Reproduction
Adjustment Frame”. If not,
perform “7. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”
is “Color Reproduction
Adjustment Frame”. If not,
perform “7. Picture Frame
Setting (Color Reproduction
Adjustment Frame)”
2
0
01
01
3
6
9D
Set the following data.
27: NTSC model
22: PAL model
27: NTSC model
22: PAL model
4
0
03
33
5
6
01
4D
Press PAUSE button.
6
6
02
Check the data changes to
“01”.
“01”.
7
1
Check that bit15 of the
display data (Note 4) is “1”.
(Note 5)
display data (Note 4) is “1”.
(Note 5)
Note 5:
When bit15 of the display data is “1”, the display data
is“8000” to “FFFF”.
is“8000” to “FFFF”.
Processing after Completing Adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE button.
2
6
9D
00
3
0
03
00
4
0
01
00
6-33
DCR-HC43
Processing after Completing Adjustment:
Reset the data setting after the adjustment finished.
Reset the data setting after the adjustment finished.
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE button.
2
6
90
00
3
6
91
00
4
6
92
00
5
6
93
00
14. Picture Frame Setting (All white frame)
Subject
Clear chart (All white frame)
(1 m (PTB-450) or 40 cm (PTB-
1450) from the front of lens)
(1 m (PTB-450) or 40 cm (PTB-
1450) from the front of lens)
Measurement Point
Video terminal of A/V OUT jack or
A/V jack (75
A/V jack (75
Ω
terminated)
Measuring Instrument
Monitor TV
Specified Value
Only the clear chart must be shot
(entire screen is white).
(entire screen is white).
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Note 2:
The right four digits of the page: 1 displayed data of the
adjusting remote commander.
adjusting remote commander.
1:XX : XX
XL or YL data
XH or YH data
XH or YH data
Switch setting
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADY SHOT (Menu setting) ..................................... OFF
5) FOCUS ................................................................... MANUAL
6) WIDE SELECT .................................................................. 4:3
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) DIGITAL ZOOM (Menu setting) .................................... OFF
4) STEADY SHOT (Menu setting) ..................................... OFF
5) FOCUS ................................................................... MANUAL
6) WIDE SELECT .................................................................. 4:3
Setting method:
Order Page Address Data
Procedure
1
While observing the TV
monitor screen, adjust the
zoom to TELE side from
WIDE side, and stop it when
the black frame of the chart
disappears.
monitor screen, adjust the
zoom to TELE side from
WIDE side, and stop it when
the black frame of the chart
disappears.
2
Check that whole of the
screen is white.
screen is white.
3
0
03
18
4
1
Read XH data and XL data.
(Note 2)
(Note 2)
5
0
03
22
6
1
Read YH data and YL data.
(Note 2)
(Note 2)
7
0
03
00
8
In the following adjustment,
if the “All white frame” is
used, adjust the clear chart to
this position.
if the “All white frame” is
used, adjust the clear chart to
this position.
How to release the zoom and focus when they deviated:
If the zoom and focus deviated due to some reason, reset them in
the following method.
If the zoom and focus deviated due to some reason, reset them in
the following method.
Order Page Address Data
Procedure
1
6
90
XL
2
6
91
XH
3
6
92
YL
4
6
93
YH
5
6
01
79
Press PAUSE button
Click on the first or last page to see other DCR-HC43 (serv.man3) service manuals if exist.