DOWNLOAD Sony DCR-HC36 / DCR-HC36E (serv.man4) Service Manual ↓ Size: 795.11 KB | Pages: 63 in PDF or view online for FREE

6-19

DCR-HC36/HC36E_ADJ

Note 1: If reading/writing data on pages 1E, set data: 01 to page:

0, address: 10, and then select pages: E. By this data set-
ting, the pages 1E can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.

Note 2: Fixed data-1: Initialized data. (Refer to“1. Initializing the

E, F, 19, 1E, 1F Page Data”)
Fixed data-2: Modified data. (Refer to“2. Modification
of E, F, 19, 1E, 1F Page Data”)

Address

Initial value

Remark

NTSC PAL

00 to FF

Fixed data-1 (Initialized data)

Note 1: If reading/writing data on pages 1F, set data: 01 to page:

0, address: 10, and then select pages: F. By this data set-
ting, the pages 1F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.

Note 2: Fixed data-1: Initialized data. (“Refer to 1. Initializing

the E, F, 19, 1E, 1F Page Data”)
Fixed data-2: Modified data. (“Refer to 2. Modification
of E, F, 19, 1E, 1F Page Data”)

Address

Initial value

Remark

NTSC PAL

00 to 1B

Fixed data-1 (Initialized data)

1C

00

00

Emergency memory address

1D

00

00

(Camera section)

1E

00

00

1F

00

00

20 to 6B

Fixed data-1 (Initialized data)

6C

Fixed data-2

6D to 93

Fixed data-1 (Initialized data)

94

Fixed data-2

95

Fixed data-1 (Initialized data)

96

97

Fixed data-2

98 to A2

Fixed data-1 (Initialized data)

A3

Fixed data-2

A4 to FE

Fixed data-1 (Initialized data)

FF

Fixed data-2

6-20

DCR-HC36/HC36E_ADJ

Before perform the camera system adjustments, check that the
specified values of “VIDEO SYSTEM ADJUSTMENTS” are sat-
isfied. (Except “36MHz Origin Oscillation Adjustment”)
Check that the data of page: 0, address: 10 is “00”.
If not, select page: 0, address: 10, and set the data “00”.

Set the frequency of the clock for synchronization.
If deviated, the synchronization will be disrupted and the color
will become inconsistent.

Subject

Not required

Measurement Point

Pin qa of IC3101 on VC-417 board

Measuring Instrument

Frequency counter

Adjustment Page

F

Adjustment Address

10

Specified value

f = 18000000 

± 90 Hz

Note 1: Check that the data of page: 0, address: 10 is “00”.

Order Page Address Data

Procedure

1

0

01

01

2

F

10

Change the data and set the
frequency (f) to the specified
value.

3

F

10

Press PAUSE (Write) button.

4

0

01

00

VC-417  board (SIDE A)

48

1

11

12

13

37

36

24

25

IC3101

Measurement Point

For detecting the position of lens iris, adjust the hall AMP gain
and offset.

Subject

Not required

Measurement Point

Displayed data of page: 1 (Note 3)

Measuring Instrument

Adjusting remote commander

Adjustment Page

F

Adjustment Address

12 to 18

Specified value

Data of page: 6, address: 0C is “00”

Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Check that the data of page: 6, address: 02 is “00”.

If not, select page: 6, address: 01, set data: 00, and press
the PAUSE (Write) button.

Switch setting:
1) POWER ............................................. CAMERA-TAPE mode

Order Page Address Data

Procedure

1

0

01

01

2

6

D0

40

3

6

01

6D

Press PAUSE (Write) button.
(Note 3)

4

6

02

Check the data changes to
“01”.

5

6

0C

Check the data is “00”.

Note 3: The adjustment data will be automatically input to page:

F, address: 12 to 18.

Order Page Address Data

Procedure

1

6

01

00

Press PAUSE (Write) button.

2

0

01

00

6-21

DCR-HC36/HC36E_ADJ

The inner focus lens flange back adjustment is carried out
automatically. In whichever case, the focus will be deviated dur-
ing auto focusing/manual focusing.

Subject

Siemens star chart with ND filter for
minipattern box (Note 1) or flange
back adjustment jig

Measurement Point

Adjustment remote commander

Measuring Instrument

Adjustment Page

F

Adjustment Address

44 to 55

Specified value

Data of page: 6, address: 0C is “00”

Note 1: Dark Siemens star chart.
Note 2: Check that the data of page: 0, address: 10 is “00”.
Note 3: Check that the data of page: 6, address: 02 is “00”.

If not, select page: 6, address: 01, set data: 00, and press
the PAUSE (Write) button.

Note 4: Perform the adjustment with the camcorder in horizontal

state.

Note 5: Perform “HALL Adjustment” before this adjustment.

Switch setting:
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) COLOR SLOW S (Menu setting) ................................... OFF

Order Page Address Data

Procedure

1

0

01

01

2

6

01

13

Press PAUSE (Write) button.

3

6

01

27

Press PAUSE (Write) button.
(Note 6)

4

6

02

Check the data changes to
“01”.

5

6

0C

Check the data is “00”.

Note 6: The adjustment data will be automatically input to page:

F, address: 44 to 55.

Order Page Address Data

Procedure

1

6

01

00

Press PAUSE (Write) button.

2

6

01

25

Press PAUSE (Write) button.

3

6

02

Check the data changes to
“01”.

4

6

01

00

Press PAUSE (Write) button.

5

0

01

00

6

Perform “Flange Back
Check”.

Preparations (Using the minipattern box)
1) The minipattern box is installed as shown in the following fig-

ure.
Note 7: The attachment lenses are not used.

2) Install the minipattern box so that the distance between it and

the front of lens of camcorder is less than 3 cm.

3) Make the height of minipattern box and the camera equal.
4) Check the output voltage of the regulated power supply is the

specified voltage 

± 0.01 Vdc.

5) Check that the center of Siemens star chart meets the center of

shot image screen with the zoom lens at TELE end and WIDE
end respectively.

Specified voltage: The specified voltage varies according to the

minipattern box, so adjust the power supply
output voltage to the specified voltage written
on the sheet which is supplied with the
minipattern box.

Preparation (Using the flange back adjustment jig)
(Luminance: about 300 lux)
1) Install the flange back adjustment jig so that the distance be-

tween it and the front of lens of camera is less than 3 cm.

2) Make the height of flange back adjustment jig and the camera

equal.

3) Check that the center of chart meets the center of shot image

screen with the zoom lens at TELE end and WIDE end respec-
tively.

Minipattern box

Below 3 cm

Camcorder

Red (+)

Black (–)

Yellow (SENS +)

White (SENS –)

Black (GND)

Need not connected

Regulated power supply

Output voltage : Specified voltage 

±0.01 Vdc

Output current : more than 3.5 A

Flange back adjustment jig

Below 3 cm

Camera

6-22

DCR-HC36/HC36E_ADJ

Order Page Address Data

Procedure

1

6

01

00

Press PAUSE (Write) button.

2

6

01

25

Press PAUSE (Write) button.

3

6

02

Check the data changes to
“01”.

4

6

01

00

Press PAUSE (Write) button.

5

0

01

00

6

Perform “Flange Back
Adjustment (2)”.

The inner focus lens flange back adjustment is carried out auto-
matically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.

Subject

Flange back adjustment chart
(2.0 m from the front of lens)
(Luminance: 300 to 400 lux)

Measurement Point

Adjustment remote commander

Measuring Instrument

Adjustment Page

F

Adjustment Address

44 to 55

Specified value

Data of page: 6, address: 0C is “00”

Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Check that the data of page: 6, address: 02 is “00”.

If not, select page: 6, address: 01, set data: 00, and press
the PAUSE (Write) button.

Note 3: Perform the adjustment with the camcorder in horizontal

state.

Note 4: Perform “HALL Adjustment” before this adjustment.

Switch setting:
1) POWER ............................................. CAMERA-TAPE mode
2) NIGHTSHOT PLUS ........................................................ OFF
3) COLOR SLOW S (Menu setting) ................................... OFF

Preparations before adjustments:
1) Place the Flange back adjustment chart 2.0 m from the front

of the lens.

2) Check that the center of Flange back adjustment chart meets

the center of shot image screen with the zoom lens at TELE
end and WIDE end respectively.

Order Page Address Data

Procedure

1

0

01

01

2

6

01

13

Press PAUSE (Write) button.

3

6

01

15

Press PAUSE (Write) button.
(Note 5)

4

6

02

Check the data changes to
“01”.

5

6

0C

Check the data is “00”.

Note 5: The adjustment data will be automatically input to page:

F, address: 44 to 55.