Sony DCR-HC36 / DCR-HC36E (serv.man4) Service Manual ▷ View online
6-15
DCR-HC36/HC36E_ADJ
6.
1C Page table
Note 1: If reading/writing data on pages 1C, set data: 01 to page:
0, address: 10, and then select pages: C. By this data set-
ting, the pages 1C can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to“00”.
ting, the pages 1C can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to“00”.
Note 2: Fixed data-1: Initialized data. (Refer to “1. Initializing
the 8, C, 18, 1C Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, C, 18, 1C Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of 8, C, 18, 1C Page Data”)
Address
Initial value
Remark
NTSC PAL
00 to B2
Fixed data-1 (Initialized data)
B3
00
00
SD error rate check (LP)
B4
00
00
B5
00
00
B6
00
00
B7
00
00
B8
80
80
B9
00
00
BA
00
00
BB
00
00
BC
00
00
BD
00
00
BE
00
00
BF
00
00
C0
00
00
C1
00
00
C2
00
00
C3
80
80
C4
00
00
C5
00
00
C6
00
00
C7
00
00
C8
00
00
C9 to D4
Fixed data-1 (Initialized data)
D5
Fixed data-2
D6 to EF
Fixed data-1 (Initialized data)
F0
Fixed data-2
F1 to FF
Fixed data-1 (Initialized data)
6-16
DCR-HC36/HC36E_ADJ
1-2-3.
Initialization of E, F, 19, 1E, 1F Page Data
1.
Initializing of E, F, 19, 1E, 1F Page Data
Note 1: If “Initialization of Pages E, F, 19, 1E, 1F” is executed,
all data on pages E, F, 19, 1E, 1F are initialized. (Only an
individual page cannot be initialized)
individual page cannot be initialized)
Note 2: If the E, F, 19, 1E, 1F page data has been initialized, the
following adjustments need to be performed again.
1) Modification of E, F, 19, 1E, 1F page data
2) Camera system adjustment (if all areas were initial-
1) Modification of E, F, 19, 1E, 1F page data
2) Camera system adjustment (if all areas were initial-
ized)
Note 3: NTSC model: DCR-HC36
PAL model: DCR-HC36E
Adjustment Page
E
Adjustment Address
00 to FF
Adjustment Page
F
Adjustment Address
10 to FF
Adjustment Page
19
Adjustment Address
00 to 33
Adjustment Page
1E
Adjustment Address
00 to FF
Adjustment Page
1F
Adjustment Address
00 to FF
Initializing method:
Order Page Address Data Procedure
1
0
01
01
2
0
10
00
Set the following data
3
6
01
2D: NTSC model
2F: PAL model
2F: PAL model
4
6
03
FF
Press PAUSE (Write) button.
5
6
02
Check the data changes to
“01”.
“01”.
6
6
01
00
Press PAUSE (Write) button.
7
Perform “Modification of E,
F, 19, 1E, 1F Page Data”
F, 19, 1E, 1F Page Data”
2.
Modification of E, F, 19, 1E, 1F Page Data
If the E, F, 19, 1E, 1F page data has been initialized, change the
data of the “Fixed data-2” address shown in the following table by
manual input.
data of the “Fixed data-2” address shown in the following table by
manual input.
Modifying Method:
1) Before changing the data, select page: 0, address: 01, and set
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) If modification of data on pages E, F, set data: 00 to page: 0,
address: 10, and then select pages E, F.
3) If modification of data on pages 19, 1E, 1F, set data: 01 to
page: 0, address: 10, and then select pages 9, E, F.
After the modification of data finished, return the data on page:
0, address: 10 to “00”.
After the modification of data finished, return the data on page:
0, address: 10 to “00”.
4) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
Note: If copy the data built in the different model, the
the data built in the same model.
Note: If copy the data built in the different model, the
camcorder may not operate.
5) When changing the data, press the PAUSE (Write) button of
the adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
data to write the data in the non-volatile memory.
6) If all areas were initialized, check that the data at the addresses
for adjustment are initial values (adjustment initial values)
listed in the table.
If different, change them to the adjustment initial values.
listed in the table.
If different, change them to the adjustment initial values.
Processing after Completing Modification E, F, 19, 1E, 1F
page data:
page data:
Order Page Address Data
Procedure
1
0
10
00
2
2
00
29
3
2
01
29
Press PAUSE (Write) button.
4
Perform “36MHz Origin
Oscillation Adjustment” of
CAMERA SYSTEM
ADJUSTMENTS.
Oscillation Adjustment” of
CAMERA SYSTEM
ADJUSTMENTS.
6-17
DCR-HC36/HC36E_ADJ
4.
F Page table
Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Fixed data-1: Initialized data. (Refer to“1. Initializing the
Note 2: Fixed data-1: Initialized data. (Refer to“1. Initializing the
E, F, 19, 1E, 1F Page Data”)
Fixed data-2: Modified data. (Refer to“2. Modification
of E, F, 19, 1E, 1F Page Data”)
Fixed data-2: Modified data. (Refer to“2. Modification
of E, F, 19, 1E, 1F Page Data”)
Address
Initial value
Remark
NTSC PAL
10
80
80
36MHz origin osillation adj.
11
Fixed data-1 (Initialized data)
12
50
50
Hall adj.
13
50
50
14
89
89
15
00
00
16
17
17
17
00
00
18
19
19
19
93
A9
MAX GAIN adj.
1A
36
36
LV standard data input
1B
00
00
1C
00
00
F No. standard data input
1D
00
00
1E
00
00
1F
00
00
20
00
00
21
00
00
22
00
00
23
00
00
24 to 29
Fixed data-1 (Initialized data)
2A
22
23
Auto white balance standard data
2B
FF
93
input
2C
08
08
2D
68
88
2E
15
15
Auto white balance adj.
2F
46
7F
30
0E
0E
31
32
19
32
Fixed data-1 (Initialized data)
33
41
42
Color reproduction adj.
34
Fixed data-1 (Initialized data)
35
2C
2A
Color reproduction adj.
36 to 39
Fixed data-1 (Initialized data)
3A
00
FF
Color reproduction adj.
3B
EF
ED
3C, 3D
Fixed data-1 (Initialized data)
3E
29
29
Auto white balance adj.
3F
40
40
40
5B
5B
41
80
80
42, 43
Fixed data-1 (Initialized data)
3.
E Page table
Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Fixed data-1: Initialized data. (Refer to“1. Initializing the
Note 2: Fixed data-1: Initialized data. (Refer to“1. Initializing the
E, F, 19, 1E, 1F Page Data”)
Fixed data-2: Modified data. (Refer to“2. Modification
of E, F, 19, 1E, 1F Page Data”)
Fixed data-2: Modified data. (Refer to“2. Modification
of E, F, 19, 1E, 1F Page Data”)
Address
Initial value
Remark
NTSC PAL
00 to 3D
Fixed data-1 (Initialized data)
3E
Fixed data-2
3F to C4
Fixed data-1 (Initialized data)
C5
Fixed data-2
C6 to E4
Fixed data-1 (Initialized data)
E5
Fixed data-2
E6 to E9
Fixed data-1 (Initialized data)
EA
Fixed data-2
EB to FF
Fixed data-1 (Initialized data)
6-18
DCR-HC36/HC36E_ADJ
5.
19 Page table
Note 1: If reading/writing data on pages 19, set data: 01 to page:
0, address: 10, and then select pages: 9. By this data set-
ting, the pages 19 can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
ting, the pages 19 can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
Note 2: Fixed data-1: Initialized data. (Refer to“1. Initializing the
E, F, 19, 1E, 1F Page Data”)
Fixed data-2: Modified data. (Refer to“2. Modification
of E, F, 19, 1E, 1F Page Data”)
Fixed data-2: Modified data. (Refer to“2. Modification
of E, F, 19, 1E, 1F Page Data”)
Address
Initial value
Remark
NTSC PAL
00 to 33
Fixed data-1 (Initialized data)
Address
Initial value
Remark
NTSC PAL
44
3A
3A
Flange back adj.
45
74
74
46
3F
3F
47
2C
2C
48
17
17
49
4A
4A
4A
00
00
4B
00
00
4C
00
00
4D
00
00
4E
4F
4F
4F
19
19
50
00
00
51
30
30
52
00
00
53
04
04
54
00
00
55
00
00
56 to 63
Fixed data-1 (Initialized data)
64
65
Fixed data-2
66 to 8C
Fixed data-1 (Initialized data)
8D
Fixed data-2
8E to 96
Fixed data-1 (Initialized data)
97
Fixed data-2
98 to FF
Fixed data-1 (Initialized data)
F Page table
Click on the first or last page to see other DCR-HC36 / DCR-HC36E (serv.man4) service manuals if exist.