DOWNLOAD Sony DCR-DVD403 / DCR-DVD403E / DCR-DVD803 / DCR-DVD803E (serv.man3) Service Manual ↓ Size: 1.04 MB | Pages: 82 in PDF or view online for FREE

6-1

DCR-DVD403/DVD403E/DVD803/DVD803E

The data that is stored in the repair board, is not necessarily correct.

Perform either procedure 1 or procedure 2 or procedure 3 when replacing board.

Save the EVR data of the machine in which a board is going to be replaced.  Download the saved data after a
board is replaced.

Remove the EEPROM and install it.

(Former board)

(New board)

Remove the EEPROM from the board of the machine that is going to be repaired.  Install the removed
EEPROM to the replaced board.

When the data cannot be saved due to defective EEPROM, or when the EEPROM cannot be removed or
installed, save the data from the same model of the same destination, and download it.

After the EVR data is saved and downloaded, check the
respective items of the EVR data.
(Refer to page 6-3 for the items to be checked)

(Machine before starting repair)

(Machine after a board is replaced)

PC

PC

Save the EVR data 
to a personal computer.

Download the saved 
data to a machine.

(Machine to be repaired)

(Machine to be repaired)

(The same model of the same destination)

Save the data.

Download the data.

PC

6-2

DCR-DVD403/DVD403E/DVD803/DVD803E

Lens device

Drive block

LCD block LCD901 (LCD panel)

LCD block LED901 (Back light)

EVF block LCD902 (LCD panel)

EVF block LED902 (Back light)

MIC unit    MIC901

Flash unit

PS13300 block (Control switch block (zoom lever))

CD-565 board IC5502 (CCD imager )

CD-565 board IC5203, X5201 (Timing generator)

CD-565 board SE7103, 7104 (YAW, PITCH sensor)

CD-565 board IC5205 (CDS)

MA-439 board IC7801 (MIC AMP)

PD-250 board IC7501 (LCD driver)

VC-397 board IC2101 (Video/Audio signal processor)

VC-397 board IC2201 (Video & Audio I/O, AGC, ACC)

VC-397 board IC2801 (16:9 wide process)

VC-397 board IC2951 (MIC AMP)

VC-397 board IC3001 (EVR)

VF-168 board IC7001 (EVF driver)

Initialization of 9, A, B, D, 13,
15, 17, 1A, 1B, page data
Initialization of E, F, 14, 19, 1E, 1F
page data
Initialization of C, 1C page data

(Note 1)

67.5MHz/54MHz origin oscillation adj.

z

z

IC2801 LINE OUT Y gain adj. 
IC2801 LINE OUT chroma gain adj. 
S VIDEO OUT Y level adj.
S VIDEO OUT chroma level adj.
IC2801adj.
HALL adj.
MR adj.
CCD output 2ch matching adj.

CAMERA
adjustment 2

Flange back and zoom lever center adj.

z

z

z

CAMERA
adjustment 3

Flange back check

z

z

Mixed color compensation adj.
F No. & ND light qualiy
standard data input
AWB standard data input
LV standard data input
AWB adj.
Color reproduction adj.
MAX GAIN adj.
Mechanical shutter adj
Strobe light level adj.
Strobe white balance adj.

CAMERA
adjustment 6

Steady shot check

z

LCD/EVF automatic adj.
White balance adj. (EVF)
V-COM adj. (LCD)

Transmissive moed
white balance adj. (LCD)
Reflective mode
white balance adj. (LCD)
Touch panel adj. 1
Touch panel adj. 2

AUDIO
adjustment

Internal 4ch microphone sensitivity adj.

z

z

POWER adj.

z

DVD-R adj.

z

DVD-RW adj.

z

DVD+RW adj.

z

Replaced parts

Parts replacement

Block replacement

Adjusting item

Adjustment

VIDEO
adjustment

(Note 1)

AUDIT

EVF/LCD
adjustment

CAMERA
adjustment 1

CAMERA
adjustment 5

CAMERA
adjustment 4

z

z

z

z

z

z

z

z

z

z

z

z

z

z

•

When replacing main parts, adjust the items indicated by z in the following table.

The Automatic Adjustment Program does not support.

6-3

DCR-DVD403/DVD403E/DVD803/DVD803E

•

When replacing a board or EEPROM, adjust the items indicated by z in the following table.

CD-565 board (COMPLETE)

MA-439 board (COMPLETE)

MD-114 board (COMPLETE)

PD-250 board (COMPLETE)

VC-397 board (COMPLETE)

VF-168 board (COMPLETE)

VC-397 board IC2002 (EEPROM)

VC-397 board IC2303 (EEPROM)

Initialization of 9, A, B, D, 13,
15, 17, 1A, 1B, page data

z

z

Initialization of E, F, 14, 19, 1E, 1F
page data

z

z

Initialization of C, 1C page data

z

z

(Note 1)

67.5MHz/54MHz origin oscillation adj.

z

z

IC2801 LINE OUT Y gain adj. 
IC2801 LINE OUT chroma gain adj. 
S VIDEO OUT Y level adj.
S VIDEO OUT chroma level adj.
IC2801adj.
HALL adj.
MR adj.
CCD output 2ch matching adj.

CAMERA
adjustment 2

Flange back and zoom lever center adj.

z

z

z

CAMERA
adjustment 3

Flange back check

z

z

z

Mixed color compensation adj.
F No. & ND light qualiy
standard data input
AWB standard data input
LV standard data input
AWB adj.
Color reproduction adj.
MAX GAIN adj.
Mechanical shutter adj
Strobe light level adj.
Strobe white balance adj.

CAMERA
adjustment 6

Steady shot check

z

z

LCD/EVF automatic adj.
White balance adj. (EVF)
V-COM adj. (LCD)

Transmissive moed
white balance adj. (LCD)
Reflective mode
white balance adj. (LCD)
Touch panel adj. 1
Touch panel adj. 2

AUDIO
adjustment

Internal 4ch microphone sensitivity adj.

z

z

POWER adj.

z

DVD-R adj.

z

DVD-RW adj.

z

DVD+RW adj.

z

z

z

z

z

z

z

z

z

z

z

z

z

z

EEPROM

replacement

Board

replacement

z

z

Adjusting item

Adjustment

VIDEO
adjustment

(Note 1)

CAMERA
adjustment 1

EVF/LCD
adjustment

AUDIT

CAMERA
adjustment 4

CAMERA
adjustment 5

When the repair is finished,
confirm the following items.

1. Shoot the all black subject (Attach

the lens cap and shoot), and con-
firm that a vertical line is not dis-
played in the center of the screen,
and that there is no difference in
left-right brightness level of the
screen.

2. Shoot a subject of low light, and

confirm that a vertical line is not
displayed in the center of the
screen, and that there is no differ-
ence in left-right brightness level
of the screen.

3. Shoot a subject of normal light, and

confirm that a vertical line is not
displayed in the center of the
screen, and that there is no differ-
ence in left-right brightness level
of the screen.
When the above symptom occurs,
perform the whole process of
“CCD Output 2ch Matching Ad-
justment”.

IC2401 (Flash memory) on
the VC-397 board and IC4403
(Flash memory) on the MD-
114 board cannot be replaced.

6-4

DCR-DVD403/DVD403E/DVD803/DVD803E

•

 Oscilloscope

•

 Color monitor

•

 Vectorscope

•

 AC power adapter

•

 Frequency counter

•

 Amplifier built-in speaker for PC

•

 Adjustment sound source file

Personal computer
(Note)

J-1

HASP key and application 
for adjustment (SeusCam)

Contact our service headquater of each area 
how to get the application for adjustment 
(SeusCam) and HASP key.

J-2

USB cable
1-829-868-41

J-3

J-4

Adjustment remote
commander
J-6082-053-B

J-12

J-14

J-7

J-5

Pattern box PTB-450
J-6082-200-A
 or
Small pattern box
PTB-1450
J-6082-557-A

J-8

Color bar chart

For PTB-450:
J-6020-250-A

For PTB-1450:
J-6082-559-A

J-9

Clear chart

For PTB-450:
J-6080-621-A

For PTB-1450:
J-6082-560-A

J-10

Minipattern box
J-6082-353-B

Siemens star chart
J-6080-875-A

Filter for color 
temperature correction
(C14)
J-6080-058-A

Back ground paper
J-2501-130-A

J-13

ND filter 1.0
J-6080-808-A

ND filter 0.4
J-6080-806-A

ND filter 0.1
J-6080-807-A

J-6

Flange back
adjustment jig
J-6082-563-A

J-15

Camera table
J-6082-384-A

Mixed color 
compensation  chart

For PTB-450:
J-6082-588-A

For PTB-1450:
J-6082-561-A

J-11

CPC-8 jig
J-6082-388-A

J-16

Extension cable
(10P)
J-6082-572-A

J-17

Extension cable
(100P)
J-6082-352-A

J-18

Personal computer
OS:

Windows98/98SE/Me/2000/XP Home/XP Pro

RAM: 256MB or more recommended
USB:

2.0 recommended (also compatible with 1.1)
Two connectors are required.