Sony DCR-DVD403 / DCR-DVD403E / DCR-DVD803 / DCR-DVD803E (serv.man3) Service Manual ▷ View online
6-17
DCR-DVD403/DVD403E/DVD803/DVD803E
8.
1F Page table
Note 1:
If reading/writing data on pages 1F, set data: 01 to page:
0, address: 10, and then select pages: F. By this data set-
ting, the pages 1F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
0, address: 10, and then select pages: F. By this data set-
ting, the pages 1F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
Note 2:
Fixed data-1: Initialized data. (“Refer to 1. Initializing
the E, F, 14, 19, 1E, 1F Page Data”)
Fixed data-2: Modified data. (“Refer to 2. Modification
of E, F, 14, 19, 1E, 1F Page Data”)
the E, F, 14, 19, 1E, 1F Page Data”)
Fixed data-2: Modified data. (“Refer to 2. Modification
of E, F, 14, 19, 1E, 1F Page Data”)
Address
Initial value
Remark
NTSC PAL
00 to AF
Fixed data-1 (Initialized data)
B0
Fixed data-2
B1
Fixed data-1 (Initialized data)
B2
Fixed data-2
B3 to E5
Fixed data-1 (Initialized data)
E6
Fixed data-2
E7
Fixed data-1 (Initialized data)
E8
Fixed data-2
E9 to FF
Fixed data-1 (Initialized data)
1-2-3.
Initialization of C, 1C Page Data
1.
Initializing of C, 1C Page Data
Note1:
If “Initialization of Pages C, 1C” is executed, all data on
pages C, 1C are initialized. (Only an individual page can-
not be initialized)
pages C, 1C are initialized. (Only an individual page can-
not be initialized)
Note2 :
If the C, 1C page data has been initialized, the following
adjustments need to be performed again.
1) Modification of C, 1C page data
2) Input of board type data
3) “VIDEO Adjustment” of the video system adjustment
4) LCD/EVF system adjustment
adjustments need to be performed again.
1) Modification of C, 1C page data
2) Input of board type data
3) “VIDEO Adjustment” of the video system adjustment
4) LCD/EVF system adjustment
Adjustment Page
C
Adjustment Address
10 to FF
Adjustment Page
1C
Adjustment Address
00 to FF
Initializing method:
Order Page Address Data
Procedure
1
0
01
01
2
0
10
00
3
3
80
0F
Press PAUSE button.
Check the data changes to
4
3
80
“1F”.
5
Perform “Modification of C,
1C Page Data”
1C Page Data”
Note 3:
If other than adjustment address was initialized, the ad-
justed data is not initialized.
justed data is not initialized.
6-18
DCR-DVD403/DVD403E/DVD803/DVD803E
2.
Modification of C, 1C Page Data
If the C, 1C page data has been initialized, change the data of the
“Fixed data-2” address shown in the following table by manual
input.
“Fixed data-2” address shown in the following table by manual
input.
Modifying Method:
1) Before changing the data, select page: 0, address: 01, and set
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) If modification of data on pages C, set data: 00 to page: 0,
address: 10, and then select pages C.
3) If modification of data on pages 1C, set data: 01 to page: 0,
address: 10, and then select pages C.
After the modification of data finished, return the data on page:
0, address: 10 to “00”.
After the modification of data finished, return the data on page:
0, address: 10 to “00”.
4) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
the data built in the same model.
Note 1:
If copy the data built in the different model, the
camcorder may not operate.
camcorder may not operate.
5) When changing the data, press the PAUSE button of the ad-
justment remote commander each time when setting new data
to write the data in the non-volatile memory.
to write the data in the non-volatile memory.
6) Check that the data at the addresses for adjustment are initial
values (adjustment initial values) listed in the table.
If different, change them to the adjustment initial values.
If different, change them to the adjustment initial values.
Processing after Completing Modification C, 1C page data:
Order Page Address Data
Procedure
1
0
10
00
2
2
00
29
3
2
01
29
Press PAUSE button.
Note 2:
This operation should be done with the adjustment re-
mote commander. The operation of page: 02 cannot be
performed with the SeusCam.
mote commander. The operation of page: 02 cannot be
performed with the SeusCam.
3.
C Page table
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Note 2:
Fixed data-1: Initialized data. (Refer to “1. Initializing
the C, 1C Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of C, 1C Page Data”)
the C, 1C Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of C, 1C Page Data”)
Address
Initial value
Remark
NTSC PAL
10 to 24
Fixed data-1 (Initialized data)
25
87
87
S VIDEO OUT Y level adj.
26
70
70
27
50
50
S VIDEO OUT chroma level adj.
28 to 3B
Fixed data-1 (Initialized data)
3C
Fixed data-2
3D, 3E
Fixed data-1 (Initialized data)
3F
6C
7A
VCO adj. (EVF)
40
90
80
41 to 44
Fixed data-1 (Initialized data)
45
7E
7E
46
7B
7B
White balance adj. (EVF)
47
58
58
Contrast adj. (EVF)
48 to 4A
Fixed data-1 (Initialized data)
4B
Fixed data-2
4C
Fixed data-1 (Initialized data)
4D
Fixed data-2
4E, 4F
Fixed data-1 (Initialized data)
50
6C
78
51
90
80
VCO adj. (LCD)
52
B6
B6
V-COM adj. (LCD)
53 to 55
Fixed data-1 (Initialized data)
56
83
83
Transmissive mode white balance
57
7F
7F
adj. (LCD)
58
5E
5E
Contrast adj. (LCD)
59 to 5C
Fixed data-1 (Initialized data)
5D
Fixed data-2
5E to 65
Fixed data-1 (Initialized data)
66
67
Fixed data-2
68 to 78
Fixed data-1 (Initialized data)
79
7A
Fixed data-2
7B
8E
8E
Reflective mode white balance
7C
87
87
adj. (LCD)
7D, 7E
Fixed data-1 (Initialized data)
7F
Fixed data-2
80
91
8E
IC2801 LINE OUT Y gain adj.
81
AD
AF
82
7B
7D
IC2801 LINE OUT chroma gain adj.
83
00
00
84
00
00
IC2801 adj.
85
00
00
6-19
DCR-DVD403/DVD403E/DVD803/DVD803E
Address
Initial value
Remark
NTSC PAL
86
00
00
IC2801 adj.
87
0C
0F
88
36
46
89
F8
18
IC2801 adj.
8A
20
21
8B to 98
Fixed data-1 (Initialized data)
99
85
8A
IC2801 adj.
9A to A0
Fixed data-1 (Initialized data)
A1
20
20
A2
20
20
IC2801 adj.
A3
20
20
A4 to F1
Fixed data-1 (Initialized data)
F2
Fixed data-2
F3 to FF
Fixed data-1 (Initialized data)
4.
1C Page table
Note 1:
If reading/writing data on pages 1C, set data: 01 to page:
0, address: 10, and then select pages: C. By this data set-
ting, the pages 1C can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to“00”.
0, address: 10, and then select pages: C. By this data set-
ting, the pages 1C can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to“00”.
Note 2:
Fixed data-1: Initialized data. (Refer to “1. Initializing
the C, 1C Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of C, 1C Page Data”)
the C, 1C Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of C, 1C Page Data”)
Address
Initial value
Remark
NTSC PAL
00 to 21
Fixed data-1 (Initialized data)
22
23
Fixed data-2
24, 25
Fixed data-1 (Initialized data)
26
27
Fixed data-2
28 to 58
Fixed data-1 (Initialized data)
59
Fixed data-2
5A to 60
Fixed data-1 (Initialized data)
61
Fixed data-2
62 to 6B
Fixed data-1 (Initialized data)
6C
Fixed data-2
6D to D5
Fixed data-1 (Initialized data)
D6
Fixed data-2
D7 to F4
Fixed data-1 (Initialized data)
F5
Fixed data-2
F6
Fixed data-1 (Initialized data)
F7
F8
Fixed data-2
F9 to FF
Fixed data-1 (Initialized data)
6-20
DCR-DVD403/DVD403E/DVD803/DVD803E
1-3. ADJUSTMENT PROGRAM
The DCR-DVD403/DVD403E/DVD803/DVD803E are adjusted
by the Automatic Adjustment Program. The Automatic Adjustment
Program enters automatically via the SeusCam the adjustment
operations that were formerly entered manually by the adjustment
remote commander (some items may be adjusted by manual op-
eration on the operation screen of the SeusCam).
by the Automatic Adjustment Program. The Automatic Adjustment
Program enters automatically via the SeusCam the adjustment
operations that were formerly entered manually by the adjustment
remote commander (some items may be adjusted by manual op-
eration on the operation screen of the SeusCam).
1.
Precautions When Using Automatic Adjustment
Program
1) The Automatic Adjustment Program writes the adjustment re-
sults such as EVR data to the set through two-way communi-
cation with the camera via the SeusCam. Accordingly, the Au-
tomatic Adjustment Program must be used in the environment
where the SeusCam operates.
cation with the camera via the SeusCam. Accordingly, the Au-
tomatic Adjustment Program must be used in the environment
where the SeusCam operates.
2) The Automatic Adjustment Program cannot be used when the
SEUS (digital camera adjustment software) is running. Exit
the SEUS before using the Automatic Adjustment Program.
the SEUS before using the Automatic Adjustment Program.
3) The SeusCam must be already started on the PC when using
the Automatic Adjustment Program. With the SeusCam not
started, some adjustment items will take time in adjustment.
started, some adjustment items will take time in adjustment.
4) The program run time may vary depending on the environ-
ment of the personal computer used.
Note:
Before using the Automatic Adjustment Program, set the
following data using the adjustment remote commander.
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: 14, set data: 01, and press the
following data using the adjustment remote commander.
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: 14, set data: 01, and press the
PAUSE button.
These settings are released if the
[END]
button is clicked
on the Main Menu screen of the Automatic Adjustment Pro-
gram.
gram.
2.
Start of Automatic Adjustment Program
Double-click the application file (DCR-DVD403 Series Auto-Adj
Ver_1.
Ver_1.
[]
r
[][]
.exe), and the Automatic Adjustment Program will start.
Note:
[]
(numeric value) of the file name varies depending on the
version of Automatic Adjustment Program.
3.
Function of Each Button on Main Menu Screen
When the Automatic Adjustment Program started, the Main Menu
screen in Fig. 6-1-8 will appear. On this screen, select each adjust-
ment section.
screen in Fig. 6-1-8 will appear. On this screen, select each adjust-
ment section.
Fig. 6-1-8
1
[Connecting the Equipment]
button
A connection diagram of the equipment is displayed.
2
[VIDEO SYSTEM ADJUSTMENT]
button
The “VIDEO SYSTEM ADJUSTMENT” screen appears.
3
[CAMERA SYSTEM ADJUSTMENT]
button
The “CAMERA SYSTEM ADJUSTMENT” screen appears.
4
[LCD SYSTEM ADJUSTMENT]
button
The “LCD SYSTEM ADJUSTMENT” screen appears.
5
[AUDIO SYSTEM ADJUSTMENT]
button
The “AUDIO SYSTEM ADJUSTMENT” screen appears.
6
[Initializing of Flash Back Up]
button
The “Initializing of Flash Back Up” screen appears.
7
[END]
button
The Automatic Adjustment Program finishes.
At this time, the data set by the adjustment remote commander
are released.
If the data are not released with the
At this time, the data set by the adjustment remote commander
are released.
If the data are not released with the
[END]
button, release them
through the following procedure using the adjustment remote
commander.
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: 14, set data: 00, and press the
commander.
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: 14, set data: 00, and press the
PAUSE button.
3) Select page: 0, address: 01, and set data: 00.
8
This part indicates the version of Automatic Adjustment Pro-
gram.
gram.
7
4
3
2
1
5
6
8
Click on the first or last page to see other DCR-DVD403 / DCR-DVD403E / DCR-DVD803 / DCR-DVD803E (serv.man3) service manuals if exist.