DOWNLOAD Sony CCD-TRV138 / CCD-TRV238E / CCD-TRV338 / CCD-TRV438E (serv.man2) Service Manual ↓ Size: 732.78 KB | Pages: 52 in PDF or view online for FREE

6-27

CCD-TRV138/TRV238E/TRV338/TRV438E

Use the following measuring instruments for video section adjust-
ments.

Note: NTSC model: CCD-TRV138/RV338

PAL model: CCD-TRV238E/TRV438E

1) TV monitor
2) Oscilloscope (dual-phenomenon, band width above 30 MHz

with delay mode) (Unless specified otherwise, use a 10 : 1
probe)

3) Frequency counter
4) Digital voltmeter
5) Audio level meter
6) Audio distortion meter
7) Regulated power supply
8) NTSC alignment tapes

• For tracking adjustment (WR5-1NU)

Parts code: 8-967-995-04

• For video frequency characteristics adjustment (WR5-10NM)

Parts code: 8-967-995-03

• For checking Standard 8 mode operations

For LP (WR5-4NL)

Parts code: 8-967-995-51

For SP (WR5-5NSP)

Parts code: 8-967-995-42

Note: The following alignment tapes can also be used.

WR5-4NSP (8-967-995-41)

• For checking Hi8 mode operations

For LP (WR5-8NLE)

Parts code: 8-967-995-52

For SP (WR5-8NSE)

Parts code: 8-967-995-43

• For BPF adjustment (WR5-11NS)

Parts code: 8-967-995-71

9) PAL alignment tapes

• For tracking adjustment (WR5-1CU)

Parts code: 8-967-995-09

• For video frequency characteristics adjustment (WR5-10CM)

Parts code: 8-967-995-08

• For checking Standard 8 mode operations

For LP (WR5-4CL)

Parts code: 8-967-995-56

For SP (WR5-5CSP)

Parts code: 8-967-995-47

Note: The following alignment tapes can also be used.

1) WR5-3CL (8-967-995-36)
2) WR5-4CSP (8-967-995-46)

• For checking Hi8 mode operations

For LP (WR5-8CLE)

Parts code: 8-967-995-57

For SP (WR5-8CSE)

Parts code: 8-967-995-48

• For BPF adjustment (WR5-11CS)

Parts code: 8-967-995-76

10) Adjustment remote commander (J-6082-053-B)
11) CPC jig connector (J-6082-539-A)
12) I/F unit for LANC control (J-6082-521-A)

6-28

CCD-TRV138/TRV238E/TRV338/TRV438E

CN007

A/V OUT jack

16

1

Audio (black)

Video (yellow)

TV monitor

AC adaptor

AC IN

AC adaptor

CPC lid

Screw (M2)

I/F unit for LANC control
(J-6082-521-A)

CPC jig connector
(J-6082-539-A)

L serices Info
LITHIUM battery (7.2Vdc)

Adjustment
remote commander (RM-95)

Conductor side

LANC jack

AC IN

This set is adjusted in two modes, VTR mode and CAMERA mode.

3-1-3. Adjusting Connectors
Some of the adjusting points of the video section are concentrated
at VC-341 board CN007. Connect the measuring instruments via
I/F unit for LANC control (J-6082-521-A) and CPC jig connector
(J-6082-539-A).
The following table shows the pin No. and signal name of CN007.

Pin No.

Signal Name

Pin No.

Signal Name

1

EEP SCK

9

PB RF

2

PB RF

10

REG GND

3

BPF MONI

11

LANC OUT

4

CAP FG

12

LANC IN

5

SWP DIR

13

XLANC PWR ON

6

REG GND

14

EEP SO

7

REC RF

15

EEP SI

8

REG GND

16

XCS EEP

Note: Use either the AC power adaptor or the InfoLITHIUM battery as the power supply of I/F unit for LANC control.

The following table lists the test point of I/F unit of for LANC
control.

Pin No.

Signal Name

Pin No.

Signal Name

BL

15

EVF VCO

14

EVF VG

BL 4.75

9

PB RF (MON)

3

BPF MONI

6, 8, 10

GND

TMS

7

REC RF (RF IN)

TDI

TDO

5

SWP

TCK

4

CAP FG

2

IR VIDEO

Note: Pin No. are those of CN007.

3-1-4. Connecting the Equipment
Connect the measuring instruments as shown in Fig. 6-3-1 and
perform the adjustments.

6-29

CCD-TRV138/TRV238E/TRV338/TRV438E

The following table lists alignment tapes which are available.
Use the tape specified in the signal column for each adjustment. If the type of tape to be used for checking operations is not specified, use
whichever type.

Tape type:

ME .................................. Particle type metal tape
MP ................................... Evaporated type metal tape

Fig. 6-3-2. shows the 75% color bar signals recorded on the alignment tape.
Note: Measure using the VIDEO terminal (Terminated at 75 

Ω).

Name

Tracking
(WR5-1NU(NTSC), WR5-1CU(PAL))

Video frequency characteristics
(WR5-10NM(NTSC), WR5-10CM(PAL))

Operation check
(WR5-5NSP(NTSC), WR5-5CSP(PAL))

Operation check
(WR5-8NSE(NTSC), WR5-8CSE(PAL))

Operation check
(WR5-4NL(NTSC), WR5-4CL(PAL))

Operation check
(WR5-8NLE(NTSC), WR5-8CLE(PAL))

BPF adjustment
(WR5-11NS(NTSC), WR5-11CS(PAL))

Tape speed

SP

SP (NTSC)
LP (PAL)

SP

SP

LP

LP

SP

Usage

Tape path adjustment, Switching position
adjustment

Frequency characteristics adjustment

Operation check

BPF adjustment

Recording mode

Standard 8

Hi8

Standard 8

Hi8

Standard 8

Hi8

Standard 8

Tape type

MP

ME

MP

ME

MP

ME

MP

Color bar signal waveform

Color bar pattern

Color bar signal waveform

1 V

0.714 V

0.286 V

White (75%)

White (100%)

Y

ello

w

Cy

an

Green

Magenta

Red

Blue

Burst signal

0.286 V

Q

I

Horizontal sync signal

(75%)

White

Y

ello

w

Cy

an

Green

Magenta

Red

Blue

Q

I

White

(100%)

Black

1 V

0.7 V

0.3 V

White (100%)

Ye

llo

w

Cy

an

Green

Magenta

Red

Blue

Burst signal

Horizontal sync signal

0.3 V

(100%)

Ye

llo

w

Cy

an

Green

Magenta

Red

Blue

White

Blac

k

Color bar pattern

6-30

CCD-TRV138/TRV238E/TRV338/TRV438E

AV MINIJACK:
Video signal: 1 Vp-p, 75 

Ω (ohms), unbalanced, sync

 negative

Audio signal: 327 mV (at output impedance more than

 47 k

Ω (kilohms))

Output impedance with less than 2.2 k

Ω (kilohms)

The record mode (Standard 8/Hi8) of this unit switches as shown
in the following table. The playback mode (Standard 8/Hi8)
switches automatically according to the recording mode of the tape
played back.

Tape Used

Recording Mode

ME

Hi8

Hi8 MP

MP

Standard 8