Sony SDM-S205F / SDM-S205K Service Manual ▷ View online
SDM-S205F, 205K (E)
13
ADJUSTMENT
1. Procedures of how to go to service mode.
1) Enter the service mode of this unit by turning on the
power while pressing and holding the "
↓" key and "↑"
simultaneously.
2) Press "MENU" key----MAINTAIN.
3) Press "OK" key to enter the service menu.
4) Select the desired function.
5) Press the "MENU" key to exit OSD.
6) Turn off the power and then turn on it again. The
3) Press "OK" key to enter the service menu.
4) Select the desired function.
5) Press the "MENU" key to exit OSD.
6) Turn off the power and then turn on it again. The
monitor then enters the normal mode. To enter the
service again, repeat the procedure described above.
service again, repeat the procedure described above.
Note
W/B readjustment is required after the panel, board and
microcomputer are replaced. However, be sure to perform
aging for more than 30 minutes for RGB reset before W/B
adjustment.
microcomputer are replaced. However, be sure to perform
aging for more than 30 minutes for RGB reset before W/B
adjustment.
2. Setup
1) Prepare timing and pattern data for a signal generator
according to the Sony timing specifications.
2) Connect a monitor video cable to the signal generator.
3) Put Color Analyzer (ex. CA-110) 50cm away from the
monitor, specify it vertically in the center of the display,
and adjust the focus to the optimum level using an
eyepiece.
4) Put the monitor and Color Analyzer (ex. CA-110) in a
light-shielded room.
5) Set up [SERVICE MODE] of the monitor.
according to the Sony timing specifications.
2) Connect a monitor video cable to the signal generator.
3) Put Color Analyzer (ex. CA-110) 50cm away from the
monitor, specify it vertically in the center of the display,
and adjust the focus to the optimum level using an
eyepiece.
4) Put the monitor and Color Analyzer (ex. CA-110) in a
light-shielded room.
5) Set up [SERVICE MODE] of the monitor.
3. Operation
Data is manually set to improve the productivity. The
brightness, contrast, and backlight are set to 50, 70 and
brightness, contrast, and backlight are set to 50, 70 and
100 respectively. After that, the default data of the color
temperature to be adjusted is set.
temperature to be adjusted is set.
4. Warm up time
Warm up for 30 minutes before performing any
adjustment.
adjustment.
5. Adjustment for White Balance
a. Display SMPTE at SXGA / 60Hz (Input level
0.73mV).
b. Set up [SERVICE MODE].
c. Click "CLEAR EEPROM" and AC Power off.
d. Set up [SERVICE MODE] of the monitor again.
e. Click "WHITE BALANCE" and then select "AUTO".
f. Prepare timing and full black pattern.
g. Click "OFFSET CALIBRATION".
h. After offset calibration is completed prepare full white
c. Click "CLEAR EEPROM" and AC Power off.
d. Set up [SERVICE MODE] of the monitor again.
e. Click "WHITE BALANCE" and then select "AUTO".
f. Prepare timing and full black pattern.
g. Click "OFFSET CALIBRATION".
h. After offset calibration is completed prepare full white
pattern.
i. Click "GAIN CALIBRATION".
6. 9300K color adjustment
a. Select "9300K" in "COLOR TEMP" and enter.
b. Use a 35% (89Gray) IRE white video field in the
b. Use a 35% (89Gray) IRE white video field in the
primary mode.
c. Adjust "CONTRAST" to secure the color temperature.
d. Press "MENU" key to exit adjust mode.
d. Press "MENU" key to exit adjust mode.
7. 6500K color adjustment
a. Select "6500K" in "COLOR TEMP" and enter.
b. Repeat the adjustment procedure as steps b to d at
b. Repeat the adjustment procedure as steps b to d at
9300K.
SDM-S205F, 205K (E)
14
SERIAL NO. LIST
Model name
Colour
Destination
Serial Range
Panel
Factory
6,500,001-6,600,000
AUO
6,700,001-6,800,000
LPL
6,000,001-6,150,000
AUO
6,300,001-6,450,000
LPL
6,500,001-6,600,000
6,500,001-6,600,000
6,700,001-6,800,000
6,700,001-6,800,000
6,500,001-6,600,000
6,700,001-6,800,000
6,700,001-6,800,000
SDM-S205K
LGE-China
BLACK
SILVER
BLACK
AEP
USA
AUO
LPL
EXPLODED VIEW
⑭
⑮
⑰
⑱
⑲
⑬
⑫
⑳
⑦
⑪
⑤
⑥
⑥
⑧
⑩
④
①
③
②
⑭
⑮
⑰
⑱
⑲
⑬
⑫
⑳
⑦
⑪
⑤
⑥
⑥
⑧
⑩
④
①
③
②
SDM-S205F, 205K (E)
15
REPLACEMENT PARTS LIST
Ref. No. SONY Part No. SONY name
X21024381
Bezel Assy (Silver)
X21024421
Bezel Assy (Black)
265409901
Knob Control (Silver)
205409911
Knob Control (Black)
3
178927011
Mounted PWB, H (Control board)
4
180597211
LCD Panel: LPL (LM201U04SL-02)
178935711
Mounted PWB, A (Main board) S205F
178935721
Mounted PWB, A (Main board) S205K
6
178936011
Mounted PWB, G (LIPS)
7
178935811
Mounted PWB, I1 (USB Main, Upstream) (S205K)
8
178935911
Mounted PWB, I2 (USB Sub, Downstream) (S205K)
9
190028528
Connector Assy
10
265409801
Connector Cover
11
178928911
Mounted PWB, L (Audio output)
265409601
Back Cabinet (S205F)
265410601
Back Cabinet (S205K)
13
265409501
Screw Cover
X21024391
HINGE ASSY (20) "Stand Body Assy" (S205F)
X21024541
PIVOT ASSY (S205K) with Stopper Pin
15
263308301
Stopper Pin
16
263391501
STAND LABEL (Stopper Caution)
17
X20594791
STAND BASE ASSY (HA)
18
263216501
Foot (HA)
19
263262801
Thumb Screw
20
265409701
SW Bracket
21
178662411
AC SWITCH with connector
22
263677401
SCREW LABEL
23
265409801
Connector, Cover
182711811
AC Power Cord (U/C)
182712011
AC Power Cord (AEP)
182711911
AC Power Cord (J)
182775711
D-SUB CABLE
182775811
DVI CABLE
182775911
AUDIO CABLE
183075311
USB CABLE (S205K)
263391108~9 CD-ROM
264902021
QUICK SETUP GUIDE (U/C)
264902011
QUICK SETUP GUIDE (AEP)
264902001
QUICK SETUP GUIDE (J)
12
14
ACCESSORIES & PACKING MATERIALS
5
1
2
※Please refer to the following URL of TV QA web page to see the latest service parts list.
http://www.tvdg.sony.co.jp/cs/sdm-pn/index.html
SONY Corporation
Made in Japan
9-878-336-02
OSAKI WEST Tec
2006.03
SDM-S205F, 205K (E)
16