Sony BDP-CX960 Service Manual ▷ View online
BDP-CX960
5
ALIGNMENT OF GEAR (CAM) PHASE WITH DOOR ASSY
MB-124-MEGA-SM BOARD SERVICE POSITION
• It is necessary to connect MB-124-MEGA-SM board (CN904) and IMD (HF) board (CN3005) with the extension cable to do the setting
• It is necessary to connect MB-124-MEGA-SM board (CN904) and IMD (HF) board (CN3005) with the extension cable to do the setting
to this position.
Prepare the following extension cables.
Part No. J-2501-068-A (19 pin, 1.00 mm pitch)
MB-124-MEGA-SM board
insulation
Connect jig (extension cable)
to the IMD (HF) board (CN3005)
to the IMD (HF) board (CN3005)
CN904
CAPACITOR ELECTRICAL DISCHARGE PROCESSING
When checking the board, for the electric shock prevention, con-
nect the resistors to both ends of respective capacitor (C106) to
discharge the capacitor (C106).
When checking the board, for the electric shock prevention, con-
nect the resistors to both ends of respective capacitor (C106) to
discharge the capacitor (C106).
HARNESS SETTING ON SWITCHING REGULATOR
Note: This illustration sees the switching regulator from component side.
door assy
gear (cam)
Align a slit of door assy with a marking on
the bottom land of gear tooth when the gear
is rotated fully in arrow direction, as shown.
the bottom land of gear tooth when the gear
is rotated fully in arrow direction, as shown.
C106
800
:/2 W
– Switching Regulator (Conductor Side) –
clamp (L35)
harness
wire
switching
regulator
regulator
power cord
BDP-CX960
6
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
2-2. CASE
(Page
(Page
7)
2-4. CHASSIS-M (HF) BLOCK
(Page
(Page
8)
2-5. FRONT PANEL BLOCK
(Page
(Page
8)
2-3. MB-124-MEGA-SM
BOARD
(Page
7)
2-6. 400D
TABLE
ASSY
(Page
9)
2-7. DRV
BOARD
(Page
9)
2-8. TABLE
(DOOR)
ASSY
(Page
10)
2-9. DC MOTOR (DOOR) (M201)
(Page
(Page
10)
2-15. BU (KEM-430AAA) ASSY
(Page
(Page
14)
2-17. SWITCHING REGULATOR
(Page
(Page
16)
2-18. BASE (CDM BD) BLOCK
(Page
(Page
17)
2-16. OPTICAL PICK-UP BLOCK
(KEM-430AAA)
(Page
(KEM-430AAA)
(Page
15)
2-10. HOLDER (TABLE SENSOR 400)
(Page
(Page
11)
2-12. SDO BOARD
(Page
(Page
12)
2-19. MOTOR (400 BD) ASSY (LOADING) (M301)/
(TABLE) (M302), MLD BOARD
(Page
17)
2-20. SLK BOARD, SLD BOARD
(Page
(Page
18)
2-13. POP-UP (400) ASSY
(Page
(Page
13)
2-11. SDT BOARD, SDR BOARD
(Page
(Page
11)
2-14. BACK PANEL BLOCK
(Page
(Page
13)
SET
BDP-CX960
7
1 five screws (BVST4 u 8)
2 two flat head screws (TP)
2 three flat head screws (TP)
1 five screws (BVST4 u 8)
3 case
Note: Follow the disassembly procedure in the numerical order given.
2-2. CASE
2-3. MB-124-MEGA-SM BOARD
3 two connectors
(CN301,
CN600)
4 SATA harness
(CN700)
1 wire (flat type)
(26 core) (CN803)
6 four screws (BVTP3 u 8)
6 screw (BVTP3 u 8)
8 screw (BVTP3 u 8)
qs heat sink (ES)
qd radiation sheet (F)
qf MB-124-MEGA-SM board
2 wire (flat type)
(21 core) (CN801)
5 wire (flat type)
(19 core) (CN904)
qa three solders
7
9 wire
0 ground plate (MB)
BDP-CX960
8
7 six connectors
(CN2501, CN2503, CN2514,
CN3001, CN4001, CN4002)
5 wire (flat type) (15 core)
(CN3012)
3 connector
(CN2511)
2 SATA harness (CN700)
4 cushion
6 two connectors
(CN3009,
CN3011)
0 four screws (BVTP3 u 8)
0 three screws (BVTP3 u 8)
0 three screws (BVTP3 u 8)
8 two screws (BVTT3 u 8)
9 two wires
qs chassis-M (HF) block
qa
A
B
C
D
E
F
G
A
B
C
F
E
D
G
1 Cut the wire holder.
Note: In reassembling, use new wire holder to
fasten the wire holder same as before.
2-4. CHASSIS-M (HF) BLOCK
2-5. FRONT PANEL BLOCK
3 connector
(CN3011)
2 wire (flat type)
(15 core) (CN3012)
1 cushion
4 three screws (BVTP3 u 8)
5 front panel block
4 five screws (BVTP3 u 8)
Click on the first or last page to see other BDP-CX960 service manuals if exist.