Sony SAL85F14Z Service Manual ▷ View online
HELP
SAL85F14Z (Planar 1.4/85) (Planar T
*
85mm F1.4 ZA)
Fixed Holding Tube Block
Install so that the burr side is upwards.
Friction Spring A
Torque Ring
Apply the adhesive bond (B-10)
(Two places to the screwed portion in the width 10 to 20mm)
(Two places to the screwed portion in the width 10 to 20mm)
Torque Ring Retainer
Focus Operation Ring
Friction Sheet
Friction Sheet
Groove
3 to 4 mm
3 to 4 mm
Groove
HELP26
Affix the friction sheet to three indicated portions of focus operation ring.
Note:
Affix the friction sheet so that the interval between the end of friction sheet and the focus operation ring is as shown in figure
below.
HELP27
Adhesive bond (B-10): J-6082-612-A
1.
Build in the friction spring A with the blurred surface place at the fixed holding tube block side.
2.
Build in the torque ring retainer to the fixed holding tube.
3.
Apply the adhesive bond (B-10) to the inner side screwed portion of torque ring holder in the width of 10 to 20mm.
4.
Tighten the torque ring holder to the fixed barrel block with the lens special fixture.
HELP
SAL85F14Z (Planar 1.4/85) (Planar T
*
85mm F1.4 ZA)
HELP28
Adhesive bond (B-40): J-6082-614-A
1.
Install the
float ring
with the torque ring greased. (Refer to HELP30.)
2.
Apply the adhesive bond to the tips of two screws.
Install the scissors lever block and fix it with two screws. (Three locations)
3.
Adjust by rotating the eccentric pin so that three scissors lever block have a play of 0.5mm and the
float ring
rotates smoothly.
Scissors Lever Block
Torque Ring
Apply the adhesive
bond (B-40)
bond (B-40)
Float Ring
Apply the adhesive bond (B-40)
Apply the adhesive
bond (B-40)
bond (B-40)
Torque Ring
Scissors Lever Block
Float Ring
Turn the eccentric pin.
Ver. 1.3 2007.10
The changed portions from
Ver. 1.2 are shown in blue.
Ver. 1.2 are shown in blue.
HELP
SAL85F14Z (Planar 1.4/85) (Planar T
*
85mm F1.4 ZA)
HELP29
Adhesive bond (G-35):
J-6082-621-A
Anti-diffusion agent (A-20): J-6082-611-A
Apply the grease (G-35) and the anti-diffusion agent (A-20) to the indicated portions of torque ring.
HELP30
Grease (G-115): J-8082-627-A
Apply the grease (G-115) to the location indicated in figure.
HELP31
Grease (G-35):
J-6082-621-A
Anti-diffusion agent (A-20): J-6082-611-A
1.
Apply the anti-diffusion agent (A-20) to the indicated portions of fixed holding tube block.
2.
Apply the grease (G-35) to the indicated portions of fixed holding tube block.
Note:
The anti-diffusion agent and the grease are applied to some locations on the same surface. This will prevent the grease from
seeping out.
Apply the anti-diffusion agent
(A-20) (All round)
(A-20) (All round)
Apply the grease (G-35)
(All round)
(All round)
Apply the grease (G-35)
(All round)
(All round)
Torque Ring
Grase is improper in this place.
Apply the grease (G-115)
(All round)
(All round)
Float Ring
Apply the anti-diffusion agent
(A-20) (All round)
(A-20) (All round)
Apply the grease (G-35) (All round)
Fixed Holding Tube Block
Ver. 1.3 2007.10
The changed portions from
Ver. 1.2 are shown in blue.
Ver. 1.2 are shown in blue.
HELP
SAL85F14Z (Planar 1.4/85) (Planar T
*
85mm F1.4 ZA)
HELP32
Adhesive bond (B-10): J-6082-612-A
1.
Apply the adhesive bond (B-10) to the indicated portions of fixed holding tube block.
2.
Install the orange color ring.
Note:
Wipe out the seeped adhesive bond on the fixed holding tube block.
HELP33
Adhesive bond (LOCTITE 460)
Note:
Use the adhesive bond (LOCTITE 460) or an equivalent article.
Do not use what becomes white after drying like quick-drying glue.
After applying the adhesive bond (LOCTITE 460) to the indicated portion of mount index, push it in the specified hole of fixed holding
tube block.
Apply the adhesive bond (B-10)
Apply the adhesive bond (B-10)
Orange Color Ring
Fixing Holding Tube Block
Apply the adhesive bond (LOCTITE 460)
Mount Index
Fixed Holding Tube Block
Click on the first or last page to see other SAL85F14Z service manuals if exist.