Sony SAL85F14Z Service Manual ▷ View online
HELP
SAL85F14Z (Planar 1.4/85) (Planar T
*
85mm F1.4 ZA)
HELP06
Adhesive bond (B-40): J-6082-614-A
Apply the adhesive bond (B-40) to the tips of three screws shown in figure and tighten the screws.
Apply the adhesive bond (B-40)
Apply the adhesive
bond (B-40)
bond (B-40)
HELP
SAL85F14Z (Planar 1.4/85) (Planar T
*
85mm F1.4 ZA)
HELP07
Adhesive bond (LOCTITE 460)
Note:
Use the adhesive bond (LOCTITE 460) or an equivalent article.
Do not use what becomes white after drying like quick-drying glue.
Anti-diffusion agent (A-20): J-6082-611-A
Grease (G-85):
J-6082-626-A
1.
Apply the adhesive bond (LOCTITE 460) to the tip of screwed portion of stopper screw and tighten the stopper screw.
2.
Apply the grease (G-85) and the anti-diffusion agent (A-20) to the indicated portions of lens mount.
3.
Combine the pins of preset ring and aperture operate plate unit, install the lens mount rivetting block.
4.
Tighten four screws catercorner shown in figure.
Lens Mount Rivetting Block
Screws
Screws
Preset Ring
Apply the anti-diffusion agent (A-20) (All round)
Apply the grease (G-85) to the hole of coupler
Apply the grease (G-85)
(3 locations of hood fixed tabs)
(3 locations of hood fixed tabs)
Apply the adhesive bond
(LOCTITE 460)
(LOCTITE 460)
HELP
SAL85F14Z (Planar 1.4/85) (Planar T
*
85mm F1.4 ZA)
HELP08
Grease (G-35): J-6082-621-A
1.
Apply the grease (G-35) to the indicated portion of coupler.
2.
Select a coupler adjustment washer of same thickness as that of back adjustment washer used in the flange back adjustment and
install it.
Part No.
Description
Thickness
2-684-057-01
Coupler Adjustment Washer A
0.05 mm
2-684-058-01
Coupler Adjustment Washer B
0.07 mm
2-684-059-01
Coupler Adjustment Washer C
0.1 mm
2-684-060-01
Coupler Adjustment Washer D
0.2 mm
2-684-061-01
Coupler Adjustment Washer E
0.5 mm
Coupler Adjustment Washer
Coupler
Apply the grease (G-35)
(All surroundings of addendum)
(All surroundings of addendum)
HELP
SAL85F14Z (Planar 1.4/85) (Planar T
*
85mm F1.4 ZA)
HELP09
1.
Assemble the focus cam ring in the groove of
float ring
, threading the guide pin of focus cam ring in the cut portion of fixed holding
tube block.
Note:
Before installation, make the cut portion and the groove of
float ring
in parallel.
When removing the fixed holding tube block, unsolder the FHB flexible unit at the lens mount side first.
2.
Install the fixed holding tube block with two screws in figure.
HELP10
Adhesive bond (B-40): J-6082-614-A
Grease (G-35):
J-6082-621-A
1.
Apply the grease (G-35) to the indicated location of gear base plate (A) block.
2.
Apply the adhesive bond (B-40) to the tips of two screws shown in figure.
Focus Cam Ring
Guide Pin
Groove of
float ring
Cut portion
Fixed Holding Tube Block
Fixed Barrel block
Apply the adhesive bond (B-40)
Apply the grease (G-35)
(All round)
(All round)
Apply the grease (G-35)
(All round)
(All round)
Apply the adhesive bond
(B-40)
(B-40)
Ver. 1.3 2007.10
The changed portions from
Ver. 1.2 are shown in blue.
Ver. 1.2 are shown in blue.
Click on the first or last page to see other SAL85F14Z service manuals if exist.