Sony SAL1855 Service Manual ▷ View online
HELP
SAL1855 (DT 3.5-5.6/18-55 SAM) (DT 18-55mm F3.5-5.6 SAM)
HELP04
1.
While inserting the aperture interlocking fork in the aperture lever, install the mount block.
2.
Select 1 to 2 pieces of back adjustment washer to make a combination of specified thickness.
Note:
The amount of back adjustment washer differs depending on the adjustment. (Refer to the flange back adjustment.)
3.
Push the back adjustment washers in between the boss and the Mount Block. (3 locations)
Note:
When stacking several pieces of back adjustment washer, install the washers so that thin one comes at the outer side.
4.
Tighten the mount block with three screws.
5.
Connect the ZF Flexible PWB to the connector of the CL-005 Mount.
Mount Block
Aperture Interlocking Fork
Aperture Lever
Back Adjustment Washer
Mount Block
ZF Flexible PWB
Back Adjustment Washer
Back Adjustment
Washer
Washer
Connector of
CL-005 Mount
CL-005 Mount
Boss
Thin
Thick
HELP
SAL1855 (DT 3.5-5.6/18-55 SAM) (DT 18-55mm F3.5-5.6 SAM)
HELP05
1.
Set the zoom to somewhere in the range of “28-35” and the focus to the infinity end.
2.
Aligning the character [DT] on the front decoration plate with the slant portion of bayonet, affix the front decoration plate.
Note:
Align with the slant portion of bayonet at the Tele stopper side.
HELP06
1.
Affix the flexible of DC Motor (Geared) to the fixed holding tube.
2.
Connect the ZF Flexible PWB to the connector.
Front Decoration Plate
Tele Stopper
Slant portion of bayonet
ZF Flexible PWB
Connector
Affix the flexible of
DC Motor (Geared) to
the Fixed Holding Tube.
DC Motor (Geared) to
the Fixed Holding Tube.
HELP
SAL1855 (DT 3.5-5.6/18-55 SAM) (DT 18-55mm F3.5-5.6 SAM)
HELP07
Adhesive bond (B-10): J-6082-612-A
1.
Cut the tip of focus brush with nippers.
2.
Install the focus brush and fix it with one screw.
Note:
Install it in the state that the focus stopper and the zoom interlocking key locate in the center.
3.
After performing the focus brush position adjustment, apply the adhesive bond (B-10) to the head of screw.
Focus Brush
Focus Stopper
Zoom Interlocking Key
Apply the adhesive bond (B-10)
Focus Brush
Cut with nippers.
HELP
SAL1855 (DT 3.5-5.6/18-55 SAM) (DT 18-55mm F3.5-5.6 SAM)
HELP08
Adhesive bond (B-10): J-6082-612-A
1.
Cut the tip of zoom brush with nippers.
2.
Install the zoom brush and fix it with one screw.
Note:
Install it in the state that the focus stopper and the zoom interlocking key locate in the center.
3.
After performing the zoom brush position adjustment, apply the adhesive bond (B-10) to the head of screw.
HELP09
1.
Install the 1st lens barrel block.
Note:
Align the index hole with the focus stopper.
2.
Turn counterclockwise the 1st lens barrel block and fix it with one screw.
Zoom Interlocking Key
Focus Stopper
Zoom Brush
Zoom Brush
Apply the adhesive
bond (B-10)
bond (B-10)
Cut with nippers.
1st Lens Barrel Block
Focus Stopper
1st Lens Barrel Block
Index hole
Click on the first or last page to see other SAL1855 service manuals if exist.