Sony SAL1855 Service Manual ▷ View online
HELP
SAL1855 (DT 3.5-5.6/18-55 SAM) (DT 18-55mm F3.5-5.6 SAM)
HELP14
Grease (FT-210): 7-640-018-91
1.
Apply the grease (FT-210) to the indicated portion of control tube block.
HELP15
1.
Align the cut portion of control tube block with the cut portion of zoom sheet.
2.
Aligning the projections of front lens barrel with the cut portions of control tube block, insert the control tube block in the front lens
barrel block.
barrel block.
HELP16
Grease (SG-310): 7-640-008-88
1.
Apply the grease (SG-310) to the indicated portions of front lens barrel. (Three locations)
Note:
Apply the grease so that the groove of helicoid is filled with grease.
2.
Apply the grease (SG-310) to the indicated portions of front lens barrel. (Three locations)
Apply the grease
(FT-210)
(FT-210)
Be careful not to apply
the grease to this area.
the grease to this area.
Control Tube Block
Control Tube Block
Zoom Sheet
Front Lens Barrel Block
Front Lens Barrel
Projection
Projection
Projection
Cut Portion
Front Lens Barrel
Apply the grease (SG-310)
Apply the grease (SG-310)
Apply the grease (SG-310)
(Fill the groove of helicoid
with the grease)
(Fill the groove of helicoid
with the grease)
Apply the grease (SG-310)
(Fill the groove of helicoid
with the grease)
(Fill the groove of helicoid
with the grease)
HELP
SAL1855 (DT 3.5-5.6/18-55 SAM) (DT 18-55mm F3.5-5.6 SAM)
HELP17
1. Mount the GPI moving barrel on the front lens barrel.
2. Rotate counterclockwise (viewing from the mount side) the GP1 moving barrel and assemble it at the position where the helicoid is
engaged (Clicked).
Note:
When moving the helicoid to the last, confirm that the bayonet click portion comes to the location where the screw hole
locates about 90 degrees apart from the pin of fixed sleeve in the clockwise direction (viewing from the mount side).
GP1 Moving Barrel
Front Lens
Barrel
Barrel
Fixed
Sleeve
Sleeve
Front Lens Barrel
GP1 Moving
Barrel
Barrel
Helicoid
Pin
Meet the Helicoids each other by rotating
counterclockwise the GP1 moving barrel
counterclockwise the GP1 moving barrel
When the helicoid engages (clicks),
assemble the GP1 moving barrel
by rotating it clockwise.
assemble the GP1 moving barrel
by rotating it clockwise.
Screw at the location where it is
clockwise (viewing from the mount)
turned by about 90 degrees from the pin
clockwise (viewing from the mount)
turned by about 90 degrees from the pin
Bayonet click portion
HELP
SAL1855 (DT 3.5-5.6/18-55 SAM) (DT 18-55mm F3.5-5.6 SAM)
HELP18
Grease (FT-210): 7-640-018-91
Grease (SG-310): 7-640-008-88
1.
Apply the grease (SG-310) to the grooves of fixed sleeve. (Three locations)
Note:
Apply the grease so that the groove is filled with grease.
2.
Apply the grease (FT-210) to the wall of oblong hole of fixed sleeve. (Six locations)
3.
Apply the grease (SG-310) to the indicated portions of GP1 moving barrel. (Six locations)
Note:
Apply the grease so that the grease remains on the wall.
4.
Apply the grease (SG-310) to the helicoids of zoom cam sleeve. (Six locations)
Note:
Apply the grease so that the grease remains on the wall.
Fixed Sleeve
Apply the grease (SG-310)
to the grooves (Three locations)
(Groove is filled)
to the grooves (Three locations)
(Groove is filled)
Apply the grease (FT-210)
to the wall of oblong hole
(Six locations)
to the wall of oblong hole
(Six locations)
GP1 Moving Barrel
Apply the grease (SG-310)
(Six inner locations)
(Six inner locations)
Apply the grease (SG-310)
(Three inner locations)
(Three inner locations)
Zoom Cam Sleeve
Apply the grease (SG-310)
(Three inner locations)
(Three inner locations)
HELP
SAL1855 (DT 3.5-5.6/18-55 SAM) (DT 18-55mm F3.5-5.6 SAM)
HELP19
1.
Align the cut portions A of fixed sleeve with the projections of GP1 moving barrel and drop the fixed sleeve in GP1 moving barrel.
2.
While holding the fixed sleeve and the GP1 moving barrel, install the zoom cam sleeve, aligning the projections of zoom cam sleeve
with the cut portions B of fixed sleeve.
3.
Align the cut portions A of fixed sleeve with the projections of GP1 moving barrel again and assemble the zoom cam sleeve by
rotating it counterclockwise (viewing from the mount side).
Fixed Sleeve
GP1 Moving Barrel
Zoom Cam Sleeve
Fixed Sleeve
GP1 Moving Barrel
Cut Portion A
Cut Portion B
Cut Portion B
Cut Portion B
Projection
Projection
Fixed Sleeve
Zoom Cam Sleeve
Fixed Sleeve
GP1 Moving
Barrel
Barrel
Cut Portion A
Projection
Rotate counterclockwise
the Zoom Cam Sleeve
(Viewing from the mount side)
the Zoom Cam Sleeve
(Viewing from the mount side)
Click on the first or last page to see other SAL1855 service manuals if exist.