DOWNLOAD Sony SAL1855 Service Manual ↓ Size: 2.09 MB | Pages: 76 in PDF or view online for FREE

2-1

SAL1855 (DT 3.5-5.6/18-55 SAM) (DT 18-55mm F3.5-5.6 SAM)

Cut and remove the part of gilt 
which comes off at the point.
(Be careful or some 
pieces of gilt may be left inside) 

• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.

Do not insert the cable insufficiently nor crookedly.

• When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped.

• When installing a connector, don’t press down at wire of connector.

It is possible that a wire is snapped.

• Do not apply excessive load to the gilded flexible board.

In case of the following notches or holes are located in the lens block, etc during disassembling/
assembling the lens, Use the universal wrench.

Attach the chip-A or chip-B to the universal wrench.
For the notches: chip-A
For the holes:

chip-B

Match the universal wrench to the holes or notches of the lens block, etc.

Notches

Holes

Universal wrench
J-6082-609-A

Chip-A for 
universal wrench:
J-6082-609-1

Chip-B for 
universal wrench:
J-6082-609-2

Notches

Chip-A

Chip-A

Chip-B

Chip-B

Chip

Fixed screw

Fixed screw

Chip

Match the universal wrench 
to the width of holes or notches.

Universal wrench

Holes

B-10

FT-210

Grease (FT-210):

7-640-018-91

Adhesive bond (B-10):

J-6082-612-A

SG-310

Grease (SG-310):

7-640-008-88

SAL1855 (DT 3.5-5.6/18-55 SAM) (DT 18-55mm F3.5-5.6 SAM)

2-2

6

5

qd

1

q;

9

8

3

2

7

1

2

5

qs

qa

6

6

4

6

q;

3

9

8

7

6

4

B-10

B-10

SG-310

SG-310

FT-210

FT-210

SG-310

FT-210

Focus Stopper

2-1-1

2-1-2

Fixed Sleeve

Zoom Interlocking Key

GP1 Moving Barrel

Zoom Brush

Focus Drive Ring

Mount Block

CL-005 Mount

Rear Holding Tube Assy

(

Note 3

)

Mount Cover

Focus Rubber Ring

Front Lens Barrel

Tele Stopper

Zoom Cam Sleeve

Back Adjustment
 Washer

Fixed Hold Ring

Focus Brush

Zoom Rubber Ring

Control Tube Block 

(

Note 3

)

Zoom Sheet

ZF Flexible Flexible 
PWB

Front Ring

Front 
Decoration Plate

Zoom Key Stopper

DC Motor
(Geared)

Switch Panel Block

(Note 2, 3)

Function Lever

Back Adjustment Washer

Back Adjustment
 Washer

1st Lens Barrel Block

2nd Lens Barrel Block

Screw

Note 1:
This lens can disassemble both the
1st lens side and the mount side. 

FLANGE BACK 
ADJUSTMENT

APERTURE DIAMETER
ADJUSTMENT

ZOOM BRUSH POSITION
ADJUSTMENT

FOCUS BRUSH POSITION
ADJUSTMENT

FOCUS-SHIFT 
ADJUSTMENT

B-10

Install the focus ring, 
orienting the concave 
step side to the eyepiece. 

Note 3
Two types of these parts, black and brown, are provided. 
Refer to Ò3.REPAIR PARTS LISTÓ.

Note 2: 
How to remove the switch panel block (Scratch prevention)
1. Remove three screws fixing the rear holding tube assy.
2. Set the AF/MF switch to AF.
3. Push the rear holding tube assy to the mount side.
4. Remove the switch panel block by inserting a Philips 
    screwdriver or a knife from the focus ring side.

SAL1855 (DT 3.5-5.6/18-55 SAM) (DT 18-55mm F3.5-5.6 SAM)

Note for assembling and grease applying positions are shown.

1.

Remove three screws fixing the rear holding tube assy.

2.

Set the AF/MF switch to AF.

3.

Push the rear holding tube assy to the mount side.

4.

Remove the switch panel block by inserting a Philips screwdriver or a knife from the focus ring side.

Switch Panel Block

Push the Rear Holding Tube Assy to the Mount side 
and insert a Philips screwdriver or a knife.

Philips screwdriver or knife.

SAL1855 (DT 3.5-5.6/18-55 SAM) (DT 18-55mm F3.5-5.6 SAM)

1.

Set the slide switch of DC Motor (Geared) to AF.

2.

Set the knob of switch panel block to AF.

3.

Peel the released paper from the switch panel block and install the switch panel block.

1.

Set the zoom to a position other than the TELE end and install the zoom key stopper.

2.

Push counterclockwise the zoom key stopper.

When installing the rear holding tube assy, insert the projection A of rear holding tube assy in the groove of zoom key

stopper.

Slide Switch
(DC Motor (Geared))

Switch Panel Block

MF Side

AF Side

Knob

Zoom Key Stopper

Rear Holding Tube Assy

Set the zoom to a position
other than the TELE end

Push counterclockwise

Projection A

Groove of the
Zoom Key Stopper