Sony SAL1855 Service Manual ▷ View online
HELP
SAL1855 (DT 3.5-5.6/18-55 SAM) (DT 18-55mm F3.5-5.6 SAM)
HELP10
1.
Set the zoom to the TELE end and insert the 2nd lens barrel block, aligning the grooves with the projections at three locations.
Note:
Align the aperture lever with the ZF flexible PWB.
2.
Set the zoom to the WIDE end, and the 2nd lens barrel block is pulled in and fixed.
Note:
If the zoom is set to the TELE end, the 2nd lens barrel block will be dislocated. Therefore, do not set the zoom to the TELE
end.
3.
Install the Tele stopper.
Note:
Install it in the state that the zoom is set to a position other than the TELE end.
4.
Push the zoom to the TELE end and tighten it with one screw.
2nd Lens Barrel Block
ZF Flexible PWB
Aperture Lever
Set to the WIDE end.
Set to the TELE end.
Projection
Projection
Projection
The 2nd lens barrel block
is pulled in and fixed.
is pulled in and fixed.
Groove
Tele Stopper
Tele Stopper
Push to the TELE end
HELP
SAL1855 (DT 3.5-5.6/18-55 SAM) (DT 18-55mm F3.5-5.6 SAM)
HELP11
How to remove the zoom interlocking key
1.
Set the zoom to the WIDE end and the focus to the NEAR end. (In the state that the zoom interlocking key and the focus stopper
locate in the center.)
2.
Remove two screws.
3.
Unlock the engagement of the bayonet by moving right and left the control tube block and shift it in the front lens barrel direction.
4.
Remove the zoom interlocking key.
Zoom Interlocking Key
Focus Stopper
Set to the WIDE end.
Set the unit to the near end.
Zoom Interlocking Key
Bayonet
HELP
SAL1855 (DT 3.5-5.6/18-55 SAM) (DT 18-55mm F3.5-5.6 SAM)
HELP12
How to install the zoom interlocking key
1.
Set the zoom to the WIDE end.
Note:
If the zoom is set to the TELE end, the front lens barrel will be dislocated. Therefore, never set the zoom to the TELE end.
2.
Set the focus to the near end by rotating.
3.
Remove the bayonet from the control tube block and shift the control tube block in the front lens barrel direction.
4.
Insert the zoom interlocking key in the hole of zoom cam sleeve and hold it.
5.
Return the control tube block and engage the bayonet with it.
6.
Align the control tube block with the hole of zoom interlocking key and tighten them with two screws.
Set the unit to the near end.
Move the hole of Zoom Cam Sleeve in
the arrow direction. (Set to the WIDE end.)
the arrow direction. (Set to the WIDE end.)
Front Lens Barrel
Bayonet
Zoom Interlocking Key
Remove the bayonet and shift the control tube
block in the front lens barrel direction.
block in the front lens barrel direction.
Hole of Zoom Cam Sleeve
Zoom Interlocking Key
Bayonet
Return the control tube block
and engage the bayonet with it.
and engage the bayonet with it.
HELP
SAL1855 (DT 3.5-5.6/18-55 SAM) (DT 18-55mm F3.5-5.6 SAM)
HELP13
1.
Aligning the pin of fixed sleeve with the pin hole of fixed hold ring, install the fixed holding tube block.
Note:
Insert the projections of front lens barrel in the grooves of focus drive ring.
2.
Fix it with three screws.
Focus Drive Ring
Front Lens Barrel
Fixed Hold Ring
Fixed Sleeve
Fixed Hold Ring Block
Pin
Groove
Groove
Groove
Projection
Projection
Projection
Pin hole
Click on the first or last page to see other SAL1855 service manuals if exist.