Sony DSC-W200 (serv.man2) Service Manual ▷ View online
2-9
DSC-W200_L2
q;
Naruto Shaft
q;
Naruto Washer
Naruto
Washer
Washer
Install the naruto washer in the direction
shown in the figure.
shown in the figure.
q;
Naruto Gear
q;
Screws
qa
Screws
qa
Barrier Assy
q;
Zoom (1210)
Gear Block Assy
q;
With the lens set to the "Tele end", install the naruto shaft, naruto washer, naruto gear and zoom (1210) gear block assy
in order. Then, fix the zoom (1210) gear block assy with two screws.
*Tightening torque=0.049 0.01N m(0.5 0.1kgf cm)
qa
Remove two screws, and remove the barrier assy.
*Discard the removed barrier assy.
2-10
DSC-W200_L2
1
Screws
3
Screws
1
New Barrier Assy
New Barrier Assy
Contacts of Parts
1
Install the new barrier assy and fix it temporarily with two screws so that it can move slightly.
2
Install temporarily the new ornamental ring (A) and adjust the position of barrier assy.
*The top sides of barrier assy and ornamental ring should be flat.
Take care for contacts of parts not to conflict each other.
Take care for contacts of parts not to conflict each other.
3
Remove the ornamental ring (A) once and tighten firmly it again with two screws with extra torque.
*Tightening torque=0.059 0.01N m(0.6 0.1kgf cm)
4
Affix the new barrier tape and then install the ornamental ring (A).
New Ornamental
Ring (A)
Ring (A)
2
New Ornamental
Ring (A)
3
New Ornamental Ring (A)
4
New Ornamental Ring (A)
4
New Barrier Tape
2
Adjust the position of barrier assy.
2-3-2. HOW TO INSTALL THE BARRIER ASSY
2-11
DSC-W200_L2
5
New Light Interception
Ring
Apply the glue to
the side of cam ring.
the side of cam ring.
6
New Ornamental
Ring (B)
7
Old Ornamental
Ring (B)
7
Rubber band
New Ornamental
Ring (B)
Ring (B)
New Ornamental
Ring (B)
Ring (B)
Old Ornamental
Ring (B)
Ring (B)
5
Install the light interception ring.
Note:
Install the light interception ring, facing its shining side down.
6
Apply the glue to the side of cam ring and install the new ornamental ring (B) while rotating it to spread the glue.
Note:
Use adhesive (Super X) or an equivalent article.
Don't use what becomes white after drying like a quick-drying glue.
7
Install the old ornamental ring (B) in the reverse direction. Fix it with a rubber band and leave for 30 minutes as is.
Note:
Load of about 500g.
Install the light interception
ring, facing its shining side down.
ring, facing its shining side down.
2-12E
DSC-W200_L2
qa
Naruto Shaft
qa
Naruto Washer
qa
Naruto Gear
qa
Screws
qa
Zoom (1210)
Gear Block Assy
8
Remove the rubber band and the old ornamental ring (B).
9
Remove two screws, zoom (1210) gear block assy, naruto gear, naruto washer, naruto gear in order.
q;
Rotate the gear of cam ring to retract the lens barrel into the camera body, and confirm that the front of camera is flat.
qa
With the lens barrel retracted into the camera body, install the naruto shaft, naruto washer, naruto gear, zoom (1210) gear
and block assy in order, and the fix the zoom (1210) gear block assy with screws.
*Tightening torque=0.049 0.01N m(0.5 0.1kgf cm)
9
Naruto Shaft
9
Naruto Washer
9
Naruto Gear
9
Screws
9
Zoom (1210)
Gear Block Assy
Confirm that the front
of camera is flat.
of camera is flat.
8
Rubber band
8
Old Ornamental
Ring (B)
Naruto
Washer
Washer
Install the naruto washer in the direction
shown in the figure.
shown in the figure.
q;
Gear of Cam Ring
Click on the first or last page to see other DSC-W200 (serv.man2) service manuals if exist.