Sony DSC-W200 (serv.man2) Service Manual ▷ View online
2-1
2. DISASSEMBLY
DSC-W200_L2
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
DISCHARGING OF THE ST-167 BOARD’S CHARGING CAPACITOR (C901)
The charging capacitor (C901) of the ST-167 board is charged
up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 k
a resistor of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
prevent electrical shock.
1 k
Ω
/1 W
Wrap insulating tape.
Note: High-voltage cautions
Discharging the Capacitor
Turn the ST-168 flexible board.
Short-circuit between the two points with the short jig about 10 seconds.
To avoid the spark with the metal plate,wrap the short jig with the
insulation tape.
Turn the ST-168 flexible board.
Short-circuit between the two points with the short jig about 10 seconds.
To avoid the spark with the metal plate,wrap the short jig with the
insulation tape.
R:1 k
Ω
/1 W
(Part code: 1-215-869-11)
Charging
Capacitor
(C901)
Capacitor
(C901)
two holes of the
battery holder
battery holder
ST-168 flexible board
ST-167 board
2-2
DSC-W200_L2
HELP
HELP
EXPLODED VIEW
HARDWARE LIST
2-1. DISASSEMBLY
2-1-1. OVERALL SECTION
Follow the disassembly in the numerical order given.
1
Cabinet (Rear) Block Assy (
1
-1 to
1
-9)
2
Cabinet (Front) Block Assy (
2
-1)
SY
-178
1
Cabinet (Rear)
Block Assy
Block Assy
2
Cabinet (Front) Block Assy
1
-7 (#20)
2
1
1
-4 (#20)
1
-1
(#20)
2
-1 (#20)
1
-6
1
-2 (Claw)
1
-8 (Claw)
1
-9
(Projection)
1
-3
Note: On installation of the cabinet (rear)
block assy, adjust the position of
the mode dial switch and the mode
dial.
the mode dial switch and the mode
dial.
Cabinet (Rear)
Block Assy.
Block Assy.
To prevent the projections at two locations
from being damaged, lift the bottom side
of cabinet (rear) block assy to the angle
shown in
from being damaged, lift the bottom side
of cabinet (rear) block assy to the angle
shown in
1
. While keeping its angle, pull
out the cabinet (rear) block assy in the
direction
direction
2
.
Note: Precaution
1
-9 (Projection) when
removing the cabinet (rear) block
assy.
assy.
1
-5 (#20)
2-3
DSC-W200_L2
EXPLODED VIEW
HARDWARE LIST
2-1-2. LCD SECTION
Follow the disassembly in the numerical order given.
1
RL Block Assy (
1
-1 to
1
-2)
2
ST-167 Board (
2
-1 to
2
-5)
3
LCD Panel/SW-501 Board (
3
-1 to
3
-2)
HELP
HELP
SY
-178
ST
-167
SW
-501
ST
-168
RL-076
1
RL Block Assy
1
-2 (Claw)
1
-1
2
-2
2
ST-167 Board
3
-1
(Claw)
3
-2 (Claw)
3
LCD Panel/SW-501 Board
2
-3
2
-5
2
-4
2
-1
Note: High-voltage cautions
Discharging the Capacitor
Turn the ST-168 flexible board.
Short-circuit between the two points with the short jig about 10 seconds.
To avoid the spark with the metal plate,wrap the short jig with the
insulation tape.
Turn the ST-168 flexible board.
Short-circuit between the two points with the short jig about 10 seconds.
To avoid the spark with the metal plate,wrap the short jig with the
insulation tape.
R:1 k
Ω
/1 W
(Part code: 1-215-869-11)
Charging
Capacitor
(C901)
Capacitor
(C901)
two holes of the
battery holder
battery holder
ST-168 flexible board
ST-167 board
2-4
DSC-W200_L2
EXPLODED VIEW
HARDWARE LIST
SY
-178
CD-705
1
Lens Block Assy
1
-1
(Claw)
1
-2
2
-1
(Solder)
2
-6
2
-3
2
-5(Claw)
2
-4
(Claw)
2
-2
(#3)
3
MC-183
Board
2
SY-178 Board
3
-1
(#20)
3
-2
HELP
HELP
HELP
HELP
HELP
HELP
1
-3
Lens Block Assy
Tension Coil
Spring
Spring
Finder Lens
Finder Lens
Note: Precaution when removing the
lens block assy.
Do not touch the area marked in the figure.
(See Page 2-6 to 2-12)
HELP
2-1-3. MAIN SECTION
Follow the disassembly in the numerical order given.
1
Lens Block Assy (
1
-1 to
1
-3)
2
SY-178 Board (
2
-1 to
2
-6)
3
MC-183 Board (
3
-1 to
3
-2)
Click on the first or last page to see other DSC-W200 (serv.man2) service manuals if exist.