Sony DSC-W200 (serv.man2) Service Manual ▷ View online
2-5
DSC-W200_L2
EXPLODED VIEW
HARDWARE LIST
2-1-4. BATTERY HOLDER SECTION
Follow the disassembly in the numerical order given.
1
BT Lid Assy (
1
-1 to
1
-2)
2
BT Holder (
2
-1 to
2
-9)
1
BT Lid Assy
2
-1
2
-2
2
-3
2
-4
2
-5
2
-6
2
-7
2
-8 (#27)
2
BT Holder
1
-1
(Open the BT Lid Assy)
1
-2
(Claw)
2
-9
2-6
DSC-W200_L2
2-2. EXCHANGE METHOD OF THE ZOOM (1210) GEAR BLOCK ASSY
2-2-1. HOW TO REMOVE THE ZOOM(1210) GEAR BLOCK ASSY
1
Remove two screws, remove the zoom (1210) gear block assy.
2
Remove soldering from the two points and remove the flexible board from the D.C. motor.
3
Remove the claws at two locations by pushing two locations of the portion A of FG leaf spring in the direction of the arrow.
Then, remove the FG leaf spring.
4
Remove the sensors at two locations and remove the flexible board from the zoom (1210) gear block assy.
1
Screws
1
Zoom (1210)
Gear Block Assy
4
Zoom (1210) Gear Block Assy
3
FG Leaf Spring
A
Claws
2
Solderings
4
Sensors
D.C. Motor
2-2-2. HOW TO INSTALL THE ZOOM(1210) GEAR BLOCK ASSY
1
Install the sensors to the new zoom (1210) gear block assy at two locations.
2
Install the FG leaf spring.
Note:
Install the claw A and claw B in order.
3
Install the flexible board to the D.C. motor and solder at two locations.
4
Install the zoom (1210) gear block assy and tighten two screws.
*Tightening torque=0.049 0.01N m(0.5 0.1kgf cm)
4
Screws
4
Zoom (1210)
Gear Block Assy
1
New Zoom (1210)
Gear Block Assy
2
FG Leaf
Spring
Claw
A
Claw
B
3
Solderings
1
Sensors
D.C. Motor
Note:
The lens should be retracted into the camera body before starting the work.
2-7
DSC-W200_L2
2-3. EXCHANGE METHOD OF THE BARRIER ASSY
2-3-1. HOW TO REMOVE THE BARRIER ASSY
1
Remove two screws, and remove the zoom (1210) gear block assy.
2
Remove the naruto gear, naruto washer and naruto shaft in order.
3
By turning the gear of cam ring, set the lens barrel to the "Tele end".
1
Screws
1
Zoom (1210)
Gear Block Assy
3
Gear of Cam Ring
2
Naruto Shaft
2
Naruto Washer
2
Naruto Gear
2-8
DSC-W200_L2
7
Pour alcohol into the inner diameter of top side of ornamental ring (A) with tweezers.
8
Remove the ornamental ring (A) while rotating it clockwise.
*
Discard the removed ornamental ring (A).
9
Peel the barrier tape.
*
Discard the removed barrier tape.
Side of Cam Ring
4
Ornamental
Ring (B)
8
Ornamental
Ring (A)
5
Light Interception
Ring
Tweezers
Cotton Swab
7
Alcohol
6
Alcohol
9
Barrier Tape
4
With the lens set to the "Tele end", remove the ornamental ring (B) while rotating it clockwise.
5
Remove the light interception ring.
*
Discard the removed light interception ring.
6
Wipe off the glue on the side of cam ring with cotton swab moistened with alcohol.
(Be careful not to drop debris of glue in the lens barrel. )
Inner diameter of top side
of Ornamental Ring (A)
of Ornamental Ring (A)
Click on the first or last page to see other DSC-W200 (serv.man2) service manuals if exist.