Sony DSC-W200 (serv.man2) Service Manual ▷ View online
DSC-W200_L2
4-1
4-1. FRAME SCHEMATIC DIAGRAM
4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
FRAME
CN004
(MULTI CONNECTOR)
1
8
1
2
13
14
CN001
SW-501 BOARD
ST-167 BOARD
LND001
LND002
LND003
LND706
LND705
LND704
+
2
26
1
25
MC-183 FLEXIBLE BOARD
S001
S002
W
(ZOOM)
T
S003
S004
S005
CN001
S006
S007
S008
S009
S010
S011
MODE DIAL
MENU
HOME
(MACRO)
(SET)
(DISP)
(FLASH)
(SELF-TIMER)
16
1
14
1
ST-168 FLEXIBLE BOARD
10
1
11
12
18
11
6
1
1
45
2
51
50
2
44
1
45
1
8
1
1
30
30
2
1
38
39
CN708
CN714
SP901
SPEAKER
CN402
IC211
(Not supplied)
CN301
CN707
CN710
CN713
LEVEL3
LEVEL3
LENS BLOCK
2.5 inch
LCD901
COLOR
LCD
MONITOR
SY-178 BOARD (SIDE B)
SY-178 BOARD (SIDE A)
LEVEL3
CD-705 FLEXIBLE BOARD
CN704
MEMORY STICK
CONNECTOR
( )
MIC901
MICROPHONE BLOCK
Note:
FLEXIBLE FLA
T CABLE (FFC-105)
CN101 is no mount.
(Direct solder)
(Direct solder)
BH001
BATTERY TERMINAL
RL-076 BOARD
1
8
CN101
BT-037 FLEXIBLE BOARD
-
S
FLEXIBLE FLA
T CABLE (FFC-106)
LCD BACKLIGHT
Note: CN001 is no mount.
(Direct solder)
BT001
LITHIUM RECHARGEBLE
BATTERY
C901
CHARGING CAPACITOR
FLASH UNIT
1
3
DSC-W200_L2
SW-501 BOARD (CONTROL SWITCH)
MC-183 FLEXIBLE BOARD
(MULTI CONNECTOR)
(MULTI CONNECTOR)
ST-168 FLEXIBLE BOARD
(BATTERY IN)
(BATTERY IN)
ST-167 BOARD
(FLASH DRIVE)
(FLASH DRIVE)
RL-076 BOARD
(CONTROL SWITCH, MIC)
(CONTROL SWITCH, MIC)
BT-037 FLEXIBLE BOARD
(DC-IN)
(DC-IN)
Link
Link
4-2. SCHEMATIC DIAGRAMS
COMMON NOTE FOR SCHEMATIC DIAGRAMS
4-2
DSC-W200_L2
4-2. SCHEMATIC DIAGRAMS
4-2. SCHEMATIC DIAGRAMS
4-2. SCHEMATIC DIAGRAMS
1. Connection
2. Adjust the distance so that the output waveform of
Fig. a and the Fig. b can be obtain.
When indicating parts by reference number, please
include the board name.
include the board name.
(For schematic diagrams)
• All capacitors are in
• All capacitors are in
µ
F unless otherwise noted. pF :
µ
µ
F. 50 V or less are not indicated except for electrolytics
and tantalums.
• Chip resistors are 1/10 W unless otherwise noted.
k
Ω
=1000
Ω
, M
Ω
=1000 k
Ω
.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum
capacitor, Because it is damaged by the heat.
Be careful not to heat the minus side of tantalum
capacitor, Because it is damaged by the heat.
• Some chip part will be indicated as follows.
Example
C541
L452
22U
10UH
TA A
2520
• Constants of resistors, capacitors, ICs and etc with XX
indicate that they are not used.
In such cases, the unused circuits may be indicated.
In such cases, the unused circuits may be indicated.
• Parts with
★
differ according to the model/destination.
Refer to the mount table for each function.
• All variable and adjustable resistors have characteristic
curve B, unless otherwise noted.
• Signal name
XEDIT
→
EDIT
PB/XREC
→
PB/REC
•
2
: non flammable resistor
•
5
: fusible resistor
•
C
: panel designation
•
A
: B+ Line
•
B
: B– Line
•
J
: IN/OUT direction of (+,–) B LINE.
•
C
: adjustment for repair.
•
A
: not use circuit
(Measuring conditions voltage and waveform)
• Voltages and waveforms are measured between the
measurement points and ground when camera shoots
color bar chart of pattern box. They are reference values
and reference waveforms.
(VOM of DC 10 M
color bar chart of pattern box. They are reference values
and reference waveforms.
(VOM of DC 10 M
Ω
input impedance is used)
• Voltage values change depending upon input
impedance of VOM used.)
Kinds of capacitor
Case size
External dimensions (mm)
Y
ellow
A
A
B
B
A=B
Fig. a (Video output terminal output waveform)
H
Cyan
Green
White
Magenta
Red
Blue
Fig.b (Picture on monitor TV)
CRT picture frame
Electronic beam
scanning frame
scanning frame
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS
(In addition to this, the necessary note is printed in each block)
(In addition to this, the necessary note is printed in each block)
Pattern box
Pattern box PTB-450
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
Color bar chart
For PTB-450:
J-6020-250-A
J-6020-250-A
For PTB-1450:
J-6082-559-A
J-6082-559-A
Pattern box
Front of the lens
L = 24 cm (PTB-450)
L = 11 cm (PTB-1450)
L = 11 cm (PTB-1450)
L
Camera
Precautions for Replacement of Imager
• If the imager has been replaced, carry out all the adjustments
for the camera section.
• As the imager may be damaged by static electricity from
its structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with
dusts nor exposed to strong light.
In addition, ensure that the receiver is not covered with
dusts nor exposed to strong light.
The components identified by mark
0
or dotted line with
mark
0
are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
0
sont
critiques pour la sécurité.
Ne les remplacer que par une pièce portant le numéro
spécifie.
Ne les remplacer que par une pièce portant le numéro
spécifie.
DSC-W200_L2
Schematic diagrams of the CD-705 flexible board and the SY-178 board are not shown.
Pages from 4-3 to 4-11 are not shown.
Pages from 4-3 to 4-11 are not shown.
Click on the first or last page to see other DSC-W200 (serv.man2) service manuals if exist.