Sony DSC-S5000 Service Manual ▷ View online
DSC-S5000
2-2
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, do not pull at wire of connector. It is
possible that a wire is snapped.
• When installing a connector, do not press down at wire of connector.
It is possible that a wire is snapped.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
The charging capacitor is charged up to the maximum 310 V
potential.
There is a danger of electric shock by this high voltage
when the capacitor is handled by hand. The electric shock
is caused by the charged voltage which is kept without dis-
charging when the main power of the unit is simply turned
off. Therefore, the remaining voltage must be discharged as
described below.
potential.
There is a danger of electric shock by this high voltage
when the capacitor is handled by hand. The electric shock
is caused by the charged voltage which is kept without dis-
charging when the main power of the unit is simply turned
off. Therefore, the remaining voltage must be discharged as
described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end
of a resistor of 1 k
of a resistor of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
prevent electrical shock.
DISCHARGING OF THE CHARGING CAPACITOR
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
1 k
Ω/1 W
Wrap insulating tape.
1 k
Ω/1 W
Wrap insulating tape.
Strobe Board
R:1 k
Ω/1 W
Charging
Capacitor
Capacitor
Charging
Capacitor
Capacitor
Strobe Board
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between two points with
the short jig about 10 seconds.
Short-circuit between two points with
the short jig about 10 seconds.
(Part code: 1-215-869-11)
DSC-S5000
2-3
2-1. EXPLODED VIEWS
2-1-1. LCD SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
DISASSEMBLY
1
X-2583-835-1 FRONT COVER ASSY (S) (SILVER)
1
X-2583-836-1 FRONT COVER ASSY (B) (BLACK)
1
X-2583-837-1 FRONT COVER ASSY (P) (PINK)
2
4-418-477-01
RIGHT CENTER ORNAMENT
3
X-2583-839-1 LCD
BRACKET
ASSY
4
X-2583-843-1 REAR COVER ASSY (S) (B) (SILVER, BLACK)
4
X-2583-844-1 REAR COVER ASSY (P) (PINK)
5
1-811-606-11 LCD
MODULE
#S1
4-137-870-01 SCREW_TP_1.7_3.7_A0.4_D3_N
(Note)
#S2
4-151-760-01
SCREW TP 1.7 L3.7 (Note)
#S3
3-288-943-01 SCREW_TP_1.4_3_A_0.2_D=2.5
#S4
3-277-534-01 SCREW_TP_1.4_3.5_A0.3_D2.5_B
1
#S1 X 1
4
Turn Over the LCD (
4
) → #S4 X 4
1. Remove in numerical order (
1
to
5
) in the left figure.
Note
#S1
Bottom View
Back View
#S4
4
Due to the weight of LCD, the LCD flexible may be
incompletely inserted in the connector. Therefore,
be careful not to make the insertion incomplete.
incompletely inserted in the connector. Therefore,
be careful not to make the insertion incomplete.
Screw's
Ref. No. (Parts Color.)
Ref. No. (Parts Color.)
Cabinet's Color
Table 2-1
Note
THE COMBINATION OF CABINET’S
COLOR AND SCREW
COLOR AND SCREW
The screw pointed is different according to the cabinet's color.
For the combination of cabinet's color and screw, please refer to Table 2-1.
A
#S1 (Silver)
A
#S2 (Black)
SILVER/PINK
BLACK
B
#S1 (Silver)
B
#S2 (Black)
PINK
SILVER/BLACK
A
B
1
2
2
1
3
4
5
5
4
3
2 (Claws)
3 (Claws)
#S1
#S2
(Note)
#S1
#S2
(Note)
#S4
#S1
#S1
#S3
#S1
4
2
Chassis Section
(See Page 2-4)
When assembling,
adjust the position.
adjust the position.
2
#S1 X 4 → #S1/#S2 X 2 → Open the Battery Cover (
2
)
→ #S3 X 1
#S1
Bottom View
Bottom View
Right View
Left View
#S1
#S1/#S2
#S3
2
The changed portions from
Ver. 1.1 are shown in blue.
Ver. 1.1 are shown in blue.
Ver. 1.2 2012.04
DSC-S5000
2-4
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
2-1-2. CHASSIS SECTION
ns: not supplied
DISASSEMBLY
52
4-416-434-01
FILTER, IR CUT (Note 4)
53
4-416-433-01
RUBBER, LIGHT INTERCEPTION
54
A-1865-538-A CCD
BLOCK
ASSY
55
A-1865-535-A STROBE
PWB
ASSY
56
4-418-668-01
MYLAR ST BLOCK (Note 1)
57
X-2583-838-1 TOP
COVER
ASSY
58
1-490-182-11
SWITCH BLOCK, CONTROL
59
A-1865-536-A MAIN MOUNTED PC BOARD
60
4-418-685-01 MAIN
FRAME
61
4-418-682-01
SHAFT, BATTERY COVER
62
4-418-683-01
SPRING, BATTERY COVER
63
X-2583-840-1 BATTERY
INNER
ASSY
64
4-418-673-01
BATTERY COVER (S) (SILVER)
64
4-418-675-01
BATTERY COVER (B) (BLACK)
64
4-418-676-01
BATTERY COVER (P) (PINK)
65
X-2583-841-1 BATTERY
TERMINAL
(+)
ASSY
66
4-418-684-01 BATTERY
TERMINAL
(-)
67
1-853-165-11
BATTERY, LITHIUM SECONDARY
68
1-542-918-11 MICROPHONE
69
1-858-616-11
SPEAKER (1.3CM) (Note 3)
70
4-426-015-01 SHEET
(MAIN-FRAME)
F1
1-576-913-31
MICRO FUSE-LINK (1608 TYPE) (1.6A/36V)
F401
1-576-363-11 FUSE (1A/30V)
#S4
3-277-534-01 SCREW_TP_1.4_3.5_A0.3_D2.5_B
#S5
3-113-001-01 SCREW
TP
1.4*2.5
1. Remove in numerical order (
1
to
6
) in the left figure.
2. The meaning of the symbol in left figure is as follows. Be careful when you remove it.
: Solder
4
#S4 X 3
1
#S4 X 5
#S4
Right View
Front View
Back View
Top View
#S4
#S4
#S4
Top View
#S4
C
B
C
B
52
(Note 4)
53
58
54
63
64
61
62
60
(Claw)
(Claw)
(Claw)
(Claw)
5
70
(Note 2)
1
57
6
59
4
55
2
56
(Note 1)
Lens Block Section
(See Page 2-5)
#S4
#S4
#S4
#S4
F1
#S4
F401
#S5
65
66
68
69
(Note 3)
67
ns
ns
#S4
#S4
3
When removing solder, be careful
not to add heat to the board and
the control switch block.
not to add heat to the board and
the control switch block.
3
DISCHARGING OF THE CHARGING CAPACITOR
6
Remove the solderings → #S4 X 2
Back View
#S4
Solder position
Solder position
Solder position
Note
Note 1: Refer to "Assembly-1: Installation Cautions of the Mylar ST
Block.".
Note 2: Refer to "Assembly-2: Installation Cautions of the Main-
Frame Sheet.".
Note 3: Refer to "Assembly-3: Installation Cautions of the Speaker
(1.3cm).".
Note 4: Refer to "Assembly-4: How to distinguish the side of Optical
Filter Block facing to Lens Device".
Caution:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
The changed portions from
Ver. 1.2 are shown in blue.
Ver. 1.2 are shown in blue.
Ver. 1.3 2013.07
DSC-S5000
2-5E
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
2-1-3. LENS BLOCK SECTION
ns: not supplied
DISASSEMBLY
101
1-492-006-11 MOTOR
UNIT
102
4-457-863-01 FIXED
BARREL
103
4-445-788-01
LONG GEAR, ZOOM
104
4-445-767-01
FOCUS GEAR, 2ND
105
4-445-790-01 DRIVE
BARREL
106
4-457-864-01
LINEAR CAM BARREL
107
4-445-765-01 ECCENTRIC
BUSH
108
4-445-793-01 CAM
BARREL
109
4-445-792-01
2ND OUTER BARREL
110
X-2586-726-1 BARRIER
ASSY
111
4-445-794-01 COSMETIC
RING
112
A-1865-537-A LENS
BLOCK
ASSY
The meaning of the symbol in left figure is as follows. Be careful when you remove it.
: Solder
111
110
109
108
107
106
105
101
104
103
102
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
112
Note
Note: Refer to 3. DISASSEMBLY/ASSEMBLY of this manual when
you exchange parts of Lens Block.
Ver. 1.3 2013.07
Click on the first or last page to see other DSC-S5000 service manuals if exist.