Sony DSC-S5000 Service Manual ▷ View online
DSC-S5000
3-13
The inner-block_1
FIXED BARREL
The only thin projection should be located around this phase.
Assembled
11. Align and assemble the inner-block_1 with FIXED BARREL as shown in the figure.
12. Attach and turn the long gear counter-clockwise to set the block in the TELE end state.
Passed
Focusing
shaft assy
shaft assy
Rear lens
13. Pass the FPC through the hole.
14. Turn the long gear clockwise to set the block in the retracted state.
15. Hook the focusing shaft assy to the rear lens as a unit as shown in the figure.
DSC-S5000
3-14
Hooked part for
Zoom drive
Zoom drive
2ND FOCUS GEAR
ZOOM LONG GEAR
16. Then, engage the unit with the certain grooves of the FIXED BARREL as shown in the figure.
17. Attach the hooked part for Zoom drive.
18. Install the ZOOM LONG GEAR and the 2ND FOCUS GEAR.
Rear lens spring
(*) ECCENTRIC BUSH:
Aligning is possible by turning it if the result of
[Focus check] is NG level in the “4. Checking
and judging” page 3-16.
[Focus check] is NG level in the “4. Checking
and judging” page 3-16.
Rear retainer
19. Put the rear lens spring.
20. Install the rear retainer with careful attention so as not to let the rear lens spring fly away.
(*) Confirm whether the ECCENTRIC BUSH is there or not.
21. Install the four screws.
DSC-S5000
3-15
To Tele, apply a positive supply voltage (+)
of DC2.5 V here.
of DC2.5 V here.
To retract, apply a positive supply voltage (+)
of DC2.5 V here.
of DC2.5 V here.
22. Install the two screws.
23. Solder the connection.
24. To test the assembly, apply a voltage of 2.5 V for DC to the zoom motor.
Mirror
Check
Dust check
1. Viewing from the front lens
No visible dust inside the lens.
2. Shooting check
2-1. Shoot the object with following conditions
- Object should be perfect white high brightness object. (Example; PTB1450 clear chart, etc)
- Shoot above object from a few centimeters with Pixel; Maximum size and Tele end.
- Shoot above object from a few centimeters with Pixel; Maximum size and Tele end.
2-2. Check the image on PC. Image should have no dust.
Focus Check
1. Preparation
- Camera installed re-assemble lens
- Test camera for comparing
- Chart (Printed PDF file at the same magnification)
- Tripod
- Mirror (ex. CD)
- Memory Stick
- PC
- Test camera for comparing
- Chart (Printed PDF file at the same magnification)
- Tripod
- Mirror (ex. CD)
- Memory Stick
- PC
2. Setting up to shoot
2-1. Paste the chart.
- Chart should be on the flat wall.
- Illuminance level in the chart should be the same.
- Make the tripod’s height and the center of the chart to the same
height.
- Enough space needed for shooting
- Illuminance level in the chart should be the same.
- Make the tripod’s height and the center of the chart to the same
height.
- Enough space needed for shooting
2-2. Set up the camera as follows;
- [P] mode
- [Maximum] size
- ISO lowest level
- Steady Shot [OFF]
- Flash [OFF]
- [Maximum] size
- ISO lowest level
- Steady Shot [OFF]
- Flash [OFF]
2-3. Attach the camera on a tripod.
2-4. Align the positions of the camera and the chart as follows;
2-4-1. Set the zoom position of the camera at Wide end.
2-4-2. Attach the mirror(*) onto the center of the chart.
2-4-2. Attach the mirror(*) onto the center of the chart.
(*) The mirror should not tilt on the chart.
3-6. Various Checks
DSC-S5000
3-16
LCD display
2-4-3. Move(*) the camera with the tripod to display the chart on LCD as the following picture.
(*) Avoid the tilt of the camera face against the chart.
2-4-4. Align the camera position(*) to the center of the chart.
(*) Adjust the position of the tripod vertically and horizontally with referring to the reflected image.
2-4-5. Reconfirm the conditions of 2-4-3. and 2-4-4. If OK, remove the mirror.
3. Shooting
3-1. Set to [Self-Timer] mode.
3-2. Take the shot by the camera installed re-assemble lens.
3-3. Take the shot by the test camera for comparing with the same condition.
3-2. Take the shot by the camera installed re-assemble lens.
3-3. Take the shot by the test camera for comparing with the same condition.
Display the frame* like in this
picture.
* Whole square frame should
be displayed.
picture.
* Whole square frame should
be displayed.
Refer to the reflected image in the mirror.
Adjust the position so that the center of Lens part
overlaps with the center of the chart.
Adjust the position so that the center of Lens part
overlaps with the center of the chart.
4. Checking and judging
4-1. Check the shot images on PC.
- Display at the same magnification of its Pixel. (100% display)
4-2. Compare the images by the repaired camera and the test camera.
- There should not be extreme focus blurring
- It should be distinguished the black and white by the sharpness between them.
- If it is in NG level, replace the lens unit.
- It should be distinguished the black and white by the sharpness between them.
- If it is in NG level, replace the lens unit.
Check the five parts (center and 4 surrounding areas) at the same magnification.
Click on the first or last page to see other DSC-S5000 service manuals if exist.