DOWNLOAD Sony DSC-S5000 Service Manual ↓ Size: 3.62 MB | Pages: 27 in PDF or view online for FREE

DSC-S5000

3-9

Shutter assy

CAM BARREL

To this cam 
groove  

The phase of 
FPC portion

The phase of the 
2nd shiny surface

The phase of the 
1st shiny surface

Assembled  
(The inner-block_4) 

1. Align the shutter assy with the CAM BARREL as shown in the figure.  

2. Assemble the inner-block_4 just by dropping the shutter assy into the CAM BARREL linearly in the arrow direction.

Assembly-4: How to distinguish the side of Optical Filter Block 

facing to Lens Device.

• IR cut coating surface

  The red coating is reflected.

• The other surface
  The red coating is 
  not reflected.

• Side view
  The red belt
  is seen.

Lens Device side

Lens Device side

Hold it with tweezers or the like.

Optical Filter  Block  

The one side of the Optical Filter Block has treated with IR cut coating.
Mount the Optical Filter Block  facing the IR cut coated side to the lens
device. Distinguish the IR cut coated side from the other by applying the
fluorescent light to the Optical Filter Block in the dark place (cut off the
outside light).

DSC-S5000

3-10

The inner-block_4

The phase of 
FPC portion

The front barrel part

To this cam groove

To this cam groove 

 

The phase of this space:  

Here is the space for the lever of
Lens barrier.  
Only this area is concave inward.   

Aligned  

3. Align the inner-block_4 with the front barrel part as shown in the figure.  

Convex part 
of the inner-
block_4

Convex part 
of the front 
barrel part  

Two grooves of 
2ND OUTER 
BARREL

 

Either three kinds of 
phases are available.

 

Entrance for the convex parts 

4. Confirm the two types of groove of 2ND OUTER BARREL, the convex of the inner-block_4, and the convex of the 

front barrel part as shown in the figure.

5. Align the 2ND OUTER BARREL with the inner-block_4 & the front barrel part as shown in the figure.

DSC-S5000

3-11

 

<1>
Put the 2ND OUTER BARREL 
linearly until it stops.       

<2>
Turn the pins of the inner-block_4 a little in 
the arrow direction to move it to the 
position shown left.    

Moved

Before move 

<3>
Push the pins of the inner-block_4 a little 
in the arrow direction. 
At this stage, the convex parts of the 
inner-block_4 have been entered in the 
groove of 2ND OUTER BARREL.    

2ND OUTER 
BARREL

6. Assemble the 2ND OUTER BARREL with the inner-block_4 & the front barrel part as shown in the figure.

Assembled  
(The inner-block_3)

Before turning three pins

After turning 

The inner-block_4

2ND OUTER BARREL

7. Turn the three pins approx. 120 degree in the arrow direction while holding the 2ND OUTER BARREL.

DSC-S5000

3-12

Linear guide ring

The inner-block_3

To this groove  

 

The phase of 
FPC portion

 

The phase of 
two cut portions

Keep holding three pins.

Keep holding the shutter assy.

Assembled  
(The inner-block_2) 

8. Align the linear guide ring with the inner-block_3 as shown in the figure.

9. Assemble the linear guide ring with the inner-block_3 as the inner-block_2 as shown in the figure.

If the linear guide ring does not fit completely, retry while keeping the three pins and the shutter assy in the arrow 
directions.  

DRIVE BARREL 

LINEAR CAM BARREL

Assembled DRIVE BARREL 
& LINEAR CAM BARREL 

The only thin projection 
should be located around 
this phase.

The phase of drive gear portion

The inner-block_1

The inner-block_2 

United DRIVE BARREL
& LINEAR CAM BARREL 

 

< Reference > 

At this point, if the DRIVE BARREL & LINEAR CAM BARREL have been separated, assemble them as 
shown in the figure.  

10. Assemble the inner-block_2 with the united DRIVE BARREL & LINEAR CAM BARREL as the inner-block_1 as 

shown in the figure.