Sony DSC-HX20 / DSC-HX20V / DSC-HX30 / DSC-HX30V (serv.man2) Service Manual ▷ View online
DSC-HX20/HX20V/HX30/HX30V_L2
1-14
q;
While holding the Feed-Through Cam Tube, turn the Rotary Tube Assy clockwise (approx. 5 degrees) and remove the Lens Block from
the Feed-Through Cam Tube.
the Feed-Through Cam Tube.
qa
Turn the Feed-Through Cam Tube and set the Projection (large) on the Feed-Through Cam Tube and the Gear of the Rotary Tube Assy
at the positions shown in the figure, and then remove the Feed-Through Cam Tube from the Rotary Tube Assy.
at the positions shown in the figure, and then remove the Feed-Through Cam Tube from the Rotary Tube Assy.
Feed-Through Cam Tube
Rotary Tube Assy
Feed-Through Cam Tube
Lens Block
Rotary Tube Assy
Feed-Through Cam Tube
Feed-Through
Cam Tube
Gear
Gear
Gear
Projection
(large)
Projection (large)
Projection
(large)
Gear
Feed-Through
Cam Tube
Eyepiece side
Eyepiece side
qs
While holding the Cam Tube (B) Assy, fully turn the Straight Tube (A) Assy clockwise (approx. 120 degrees) and remove
the 2nd-4th Lens Block from the 1st Lens Block.
the 2nd-4th Lens Block from the 1st Lens Block.
qd
Remove the Ornamental Ring (A), Barrier Assy, and 1st Lens Assy from the Straight Tube (A) Assy.
Note: For how to remove the Ornamental Ring (A), Barrier Assy, and 1st Lens Assy, refer to "1-8. Ornamental Ring A or Barrier Assy
Note: For how to remove the Ornamental Ring (A), Barrier Assy, and 1st Lens Assy, refer to "1-8. Ornamental Ring A or Barrier Assy
Replacing Method."
1st Lens Block
2nd-4th Lens Block
Straight Tube (A) Assy
Straight Tube (A) Assy
Cam Tube (B) Assy
For how to remove the Ornamental Ring (A),
Barrier Assy, and 1st Lens Assy, refer to "1-8.
Ornamental Ring A or Barrier Assy
Replacing Method."
1st Lens Assy
Barrier Assy
Ornamental Ring (A)
Note:
DSC-HX20/HX20V/HX30/HX30V_L2
1-15
qf
qg
While holding the Straight Tube (B), fully turn the Cam Tube (A) and the Cam Tube (B) Assy counterclockwise (approx. 125 degrees)
to extend the Straight Tube (B).
Remove the 4th Lens Assy.
to extend the Straight Tube (B).
Remove the 4th Lens Assy.
qh
qj
While holding the Straight Tube (B), turn the Cam Tube (A) and the Cam Tube (B) Assy clockwise (approx. 125 degrees) to set them to
the retracted state.
Remove the 2nd Lens Assy from the eyepiece side.
the retracted state.
Remove the 2nd Lens Assy from the eyepiece side.
qk
Remove the Cam Tube (A).
Straight Tube (B)
Cam Tube (A),
Cam Tube (B) Assy
Cam Tube (A),
Cam Tube (B) Assy
Straight Tube (B)
4th Lens Assy
2nd Lens Assy
Straight Tube (B)
Cam Tube (A)
ql
While holding the Straight Tube (B), fully turn the Cam Tube (B) Assy counterclockwise (approx. 3 degrees) and remove
the 3rd Lens Assy from the eyepiece side.
the 3rd Lens Assy from the eyepiece side.
w;
wa
Turn the Cam Tube (B) Assy to align the Cam Tube (B) Assy hole with the cutout of the Straight Tube (B) as shown in the figure.
Detach the Cam Tube (B) Assy from the Straight Tube (B).
Detach the Cam Tube (B) Assy from the Straight Tube (B).
3rd Lens Assy
Cam Tube (B) Assy
Straight Tube (B)
Cam Tube (B) Assy
Cam Tube (B) Assy
Straight Tube (B)
Hole
Cutout
DSC-HX20/HX20V/HX30/HX30V_L2
1-16
Install the Cam Tube (B) Assy to the Straight Tube (B) with the hole aligned with the cutout.
Turn the Cam Tube (B) Assy counterclockwise (approx. 141.5 degrees) from the assembled position to align the Groove (tight)
of the Straight Tube (B) with the Groove (3rd Lens Assy Inlet) of the Cam Tube (B) Assy as shown in the figure.
Turn the Cam Tube (B) Assy counterclockwise (approx. 141.5 degrees) from the assembled position to align the Groove (tight)
of the Straight Tube (B) with the Groove (3rd Lens Assy Inlet) of the Cam Tube (B) Assy as shown in the figure.
Cam Tube (B) Assy
Cam Tube (B) Assy
Groove
(3rd Lens Assy Inlet)
Straight Tube (B)
Hole
Cutout
Installation
Align the Flexible Board with the Step as shown in the figure and install the 3rd Lens Assy while inserting the three Projections of
the 3rd Lens Assy into the three Grooves (tight) of the Straight Tube (B).
While holding the Straight Tube (B), turn the Cam Tube (B) Assy clockwise (approx. 3 degrees) to retain the 3rd Lens Assy position.
the 3rd Lens Assy into the three Grooves (tight) of the Straight Tube (B).
While holding the Straight Tube (B), turn the Cam Tube (B) Assy clockwise (approx. 3 degrees) to retain the 3rd Lens Assy position.
3rd Lens Assy
Projections
Flexible Board
Cam Tube (B) Assy
Straight Tube (B)
Grooves
(tight)
Groove
(tight)
Step
Cam Tube (A),
Cam Tube (B) Assy
Cam Tube (A),
Cam Tube (B) Assy
Hole
Flexible
Board
Bayonet
(wide)
5
Align the Bayonet (wide) with the hole and install the Cam Tube (A).
Cam Tube (A)
6
7
Align the White Part with the Bayonet (wide) and install the 2nd Lens Assy while inserting the three Guide keys into the three Guide grooves.
While holding the Straight Tube (B), fully turn the Cam Tube (A) and the Cam Tube (B) Assy counterclockwise (approx. 125 degrees)
to set them at TELE end.
While holding the Straight Tube (B), fully turn the Cam Tube (A) and the Cam Tube (B) Assy counterclockwise (approx. 125 degrees)
to set them at TELE end.
2nd Lens Assy
Straight Tube (B)
Bayonet
(wide)
White part
Guide key
Guide keys
Guide groove
Guide grooves
Guide keys
Guide key
Guide groove
Guide
grooves
8
9
Align the Flexible Board with the Flexible Board and install the 4th Lens Assy while inserting the three Guide keys into the three Guide grooves.
While holding the Straight Tube (B), fully turn the Cam Tube (A) and the Cam Tube (B) Assy clockwise (approx. 125 degrees) to set them
to the retracted state.
to the retracted state.
Straight Tube (B)
4th Lens Assy
Flexible
Board
DSC-HX20/HX20V/HX30/HX30V_L2
1-17
q;
Straight Tube (A) Assy
Groove (wide)
Align the White Part with the Groove (wide) as shown in the figure and install the 1st Lens Assy to the Straight Tube (A) Assy
while inserting the three Guide keys into the three Guide grooves.
while inserting the three Guide keys into the three Guide grooves.
qa
qs
Align the Bayonet (wide) with the Groove (wide) and install the 2nd-4th Lens Block to the Straight Tube (A) Assy.
Bayonet (wide)
While holding the Cam Tube (B) Assy, fully turn the Straight Tube (A) Assy clockwise (approx. 120 degrees) to set it to the retracted state.
Straight Tube (A) Assy
Cam Tube (B) Assy
2nd-4th Lens Block
1st Lens Assy
Straight Tube (A) Assy
Guide keys
White Part
Guide grooves
Groove (wide)
Guide groove
qd
qf
Align the Projection (large) with the Gear as shown in the figure and install the Feed-Through Cam Tube to the Rotary Tube Assy.
Turn the Feed-Through Cam Tube in the arrow direction to set the Projection (large) and the Gear to the positions shown in the figure.
qg
qh
Align the semicircular edge with the Naruto Gear mounting hole as shown in the figure and install the Feed-Through Cam Tube and
the Rotary Tube Assy to the Stationary Tube.
Engage the seven Projections of the Feed-Through Cam Tube with the seven Grooves of the Stationary Tube.
the Rotary Tube Assy to the Stationary Tube.
Engage the seven Projections of the Feed-Through Cam Tube with the seven Grooves of the Stationary Tube.
Rotary Tube Assy
Feed-Through Cam Tube
Feed-Through
Cam Tube
Feed-Through Cam Tube
Gear
Gear
Gear
Projection
(large)
Projection (large)
Projection
(large)
Feed-Through
Cam Tube
Eyepiece side
Eyepiece side
Projection
(large)
Naruto Gear
mounting hole
Feed-Through Cam Tube,
Rotary Tube Assy
Stationary Tube
Stationary Tube
Semicircular edge
Click on the first or last page to see other DSC-HX20 / DSC-HX20V / DSC-HX30 / DSC-HX30V (serv.man2) service manuals if exist.