DOWNLOAD Sony DSC-HX20 / DSC-HX20V / DSC-HX30 / DSC-HX30V (serv.man2) Service Manual ↓ Size: 7.38 MB | Pages: 34 in PDF or view online for FREE

Model
DSC-HX20 DSC-HX20V DSC-HX30 DSC-HX30V (serv.man2)
Pages
34
Size
7.38 MB
Type
PDF
Document
Service Manual
Brand
Device
Digital Camera / LEVEL2
File
dsc-hx20-dsc-hx20v-dsc-hx30-dsc-hx30v-sm2.pdf
Date

Sony DSC-HX20 / DSC-HX20V / DSC-HX30 / DSC-HX30V (serv.man2) Service Manual ▷ View online

DSC-HX20/HX20V/HX30/HX30V_L2
Sony Corporation
SERVICE MANUAL
Revision History
SERVICE  NOTE (Check the following note before the service.)
LEVEL 
2
Published by Sony Techno Create Corporation
983465937.pdf
Ver. 1.6  2013.03
DIGITAL STILL CAMERA
The components identified by 
mark 
0 or dotted line with mark 
0 are critical for safety.
Replace only with part number 
specified.
Les composants identifiés par 
une marque 
0 sont critiques pour 
la sécurité.
Ne les remplacer que par une piè-
ce portant le numéro spécifié.
US Model
Canadian Model
AEP Model
UK Model
E Model
Australian Model
Hong Kong Model
Chinese Model
Korea Model
Japanese Model
Photo: DSC-HX30V/BLACK
9-834-659-37
DSC-HX20/HX20V/HX30/HX30V
Ver.
Date
History
Contents
S.M. Rev.
issued
1.0
2012.03
Official Release
1.1
2012.05
Revised-1
(A1 12-008)
•  Addition of SERVICE NOTE.
 Page 
1-6
1-11
1-12
1-13
1-19
•  Revision of EXPLODED VIEWS.
 Page 
2-3
2-4
2-5
2-6
2-7
• Correction of ACCESSORIES.
 Page 
2-8
•  Addition of Flyer
Yes
1.2
2012.06
Revised-2
(A2 12-082)
•  Addition of DSC-HX20.
 Page 
2
1-5
1-11
2-3
2-6
Yes
1.3
2012.09
Revised-3
(A2 12-229)
•  Addition of Australian Model (DSC-HX30V).
 Page 
2
1-5
1-11
2-3
Yes
1.4
2012.10
Revised-4
(A4 12-257)
•  Addition of SERVICE NOTE.
 Page 
1-1
1-6
1-7
•  Addition of REPAIR PARTS LIST.
 Page 
2-3
2-5
Yes
1.5
2013.02
Revised-5
(A5 12-332)
•  Addition of SERVICE NOTE.
 Page 
1-5
1-11
•  Revision of EXPLODED VIEWS.
 Page 
2-4
Yes
1.6
2013.03
Revised-6
(A6 12-362)
•  Addition of SERVICE NOTE.
 Page 
1-1
,
 1-6
Yes
2013C08-1
  © 2013.03
– ENGLISH –
1-1.  PRECAUTION ON REPLACING THE SY-325 BOARD
1-2.  ADDITION OF DESTINATION DATA FILE
1-3.  METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
1-4.  HOW TO WRITE DATA TO INTERNAL MEMORY
1-5. SELF-DIAGNOSIS 
FUNCTION
1-6.  PROCESS AFTER FIXING FLASH ERROR
1-7.   PRECAUTION ON REPLACING THE CABINET (BOTTOM)
1-8.  CHECKING THE Wi-Fi FUNCTION
1-9.  ORNAMENTAL RING A OR BARRIER ASSY REPLACING METHOD
1-10. ZOOM MOTOR GEAR BLOCK REPLACING METHOD
1-11.  CAM TUBE (B) ASSY REPLACING METHOD
1-12. FINAL  INSPECTION
‒ JAPANESE ‒
1-1.  SY-325基板交換時の注意
1-2.  Destination Data ファイルの追加について
1-3.  内蔵メモリーのデータコピーおよび消去方法
1-4.  内蔵メモリーへデータを書き戻す方法
1-5.  自己診断機能
1-6.  フラッシュエラー発生時の対処法
1-7.  キャビネット(底)交換時の注意
1-8.  Wi-Fi機能の確認
Internal memory
ON BOARD
Internal memory
ON BOARD
Revised-6
Replace the previously issued
SERVICE MANUAL 9-834-659-36
with this Manual.
DSC-HX20/HX20V/HX30/HX30V_L2
– 2 –
SPECIFICATIONS
概略仕様
– ENGLISH –
– JAPANESE –
本体
[システム]
撮像素子:
7.76 mm 
1/2.3
型)
 
Exmor R CMOS
センサー
総画素数:約
1890
万画素
カメラ有効画素数:約
1820
万画素
レンズ:
Sony G 20
倍ズームレンズ
 f=4.45 
mm
 
 89 mm
 
25 
mm
 
 500 mm
35 mm
フィ
 
ルム換算値))、
F3.2
W
)∼
 F5.8
T
 
動画撮影時(
16
9
):
27.5 
mm
 
 550 
mm*
 
動画撮影時(
4
3
):
34 
mm
 
 680 
mm*
 
*
 
動画手ブレ補正]が[スタンダード]のとき
手ブレ補正:光学式
露出制御:自動、マニュアル露出、シーン
 
セレクション(
15
モード)
ホワイトバランス:オート、太陽光、曇天、
 
蛍光灯
1
2
3
、電球、フラッシュ、ワ
 
ンプッシュ、ホワイトバランスシフト
信号方式:
NTSC
カラー、
EIA
標準方式
記録方式:
 
静止画記録方式:
 JPEG
DCF
Exif
MPF Baseline
 
準拠、
DPOF
対応
 3D
静止画記録方式:
MPO
MPF
 Extended
(立体視))準拠
 
動画記録方式(
AVCHD
方式):
 AVCHD
規格
 Ver.2.0
準拠
 
映像:
MPEG-4 AVC/H.264
 
音声:
Dolby Digital 2ch
 
ドルビーデジタルステレオクリエー
 
ター搭載
 
 
ドルビーラボラトリーズからの実施権に基づき
製造されています。
 
動画記録方式(
MP4
方式):
 
映像:
MPEG-4 AVC/H.264
 
音声:
MPEG-4 AAC-LC 2ch
記録メディア:内蔵メモリー
 
105 MB
 
“メモリースティック
 
デュオ”、
SD
 
カード、“メモリースティック
 
マイク
 
ロ”、
microSD 
メモリーカード
フラッシュ:撮影範囲(
ISO
感度(推奨露
 
光指数)がオートのとき)
 
0.4 
m∼
 7.1 m
W
/
1.5 
m∼
 3.9 
m
T
[入出力端子]
HDMI
端子:
HDMI
ミニ端子
マイクロ
USB
端子:
USB
通信
USB
通信:
Hi-Speed USB
USB 2.0
[モニター]
液晶モニター:
 7.5 
cm
3.0
型)、
TFT
駆動
総ドット数:
921 600
ドット
[電源・その他]
電源:リチャージャブルバッテリー
 
パック
NP-BG1
3.6 V
 NP-FG1
(別売)、
3.6 V
 AC
アダプター
 AC-UB10/UB10B
 5 
V
消費電力(撮影時):
 
1.1 W
動作温度:
℃∼
 40 
保存温度:−
20 
℃∼
 +60 
外形寸法(
CIPA
準拠):
 106.6 
mm
×
61.9 mm
×
34.6 mm
 
(幅×高さ×奥行き)
本体質量(
CIPA
準拠)
 
(バッテリー
NP-BG1
、“メモリース
 
ティック
 
デュオ”を含む):
 
254 g
マイクロホン:ステレオ
スピーカー:モノラル
Exif Print
:対応
PRINT Image Matching III
:対応
[ワイヤレスLAN]
対応規格:
IEEE 802.11b/g/n
ACアダプター
AC-UB10/UB10B
定格入力:
AC 100 V 
 240 V
 
50 Hz/60 Hz
70 mA
定格出力:
DC 5 V
0.5 A
動作温度:
℃∼
 40 
保存温度:−
20 
℃∼
 +60 
外形寸法:約
50 mm
×
22 mm
×
54 mm
 
(幅×高さ×奥行き)
本体質量:約
48 g
リチャージャブルバッテリー
パックNP-BG1
使用電池:リチウムイオン蓄電池
最大電圧:
DC 4.2 V
公称電圧:
DC 3.6 V
容量:
3.4 Wh
960 mAh
本機や付属品の仕様および外観は、改良
のため予告なく変更することがあります
が、ご了承ください。
Model information table
Model
DSC-HX20
DSC-HX20V
DSC-HX30
DSC-HX30V
Destination
AEP
US
E
AEP, E, AUS
UK
CH
US, J
CND, E, KR
HK, 
AUS
Color system
PAL
NTSC
NTSC
PAL
PAL
PAL
NTSC
NTSC
PAL
GPS
TransferJet
• Abbreviation
  AUS :  Australian model
  CH :   Chinese model
  CND :  Canadian model
  HK :  Hong Kong model
  J : 
Japanese model
  KR :   Korea model
Camera
[System]
Image device: 7.76 mm (1/2.3 type)
 
Exmor R CMOS sensor
Total pixel number of camera:
 
Approx. 18.9 Megapixels
Effective pixel number of camera:
 
Approx. 18.2 Megapixels
Lens: Sony G 20× zoom lens
 
f = 4.45 mm – 89 mm (25 mm –
 
500 mm (35 mm film equivalent))
 
F3.2 (W) – F5.8 (T)
 
While shooting movies (16:9):
 
27.5 mm – 550 mm*
 
While shooting movies (4:3):
 
34 mm – 680 mm*
 
*
  
When [Movie SteadyShot] is set to 
[Standard]
SteadyShot: Optical
Exposure control: Automatic exposure,
 
Manual exposure, Scene Selection
 (15 
modes)
White balance: Automatic, Daylight,
 
Cloudy, Fluorescent 1/2/3,
 
Incandescent, Flash, One Push,
 
White Balance Shift
Signal format:
 
For 1080 50i:
 
PAL color, CCIR standards HDTV
 
1080/50i, 1080/50p specification
 
For 1080 60i:
 
NTSC color, EIA standards HDTV
 
1080/60i, 1080/60p specification
File format:
 
Still images: JPEG (DCF, Exif,
 
MPF Baseline) compliant, DPOF
 compatible
 
3D still images: MPO (MPF
 
Extended (Disparity Image))
 compliant
 
Movies (AVCHD format):
 
AVCHD format Ver. 2.0
 compatible
 Video: 
MPEG-4 
AVC/H.264
 
Audio: Dolby Digital 2ch,
 
equipped with Dolby Digital Stereo
 Creator
 
  
Manufactured under license from
Dolby Laboratories.
 
Movies (MP4 format):
 Video: 
MPEG-4 
AVC/H.264
 
Audio: MPEG-4 AAC-LC 2ch
Recording media: Internal Memory
 
(Approx. 105 MB), “Memory Stick
 
Duo” media, SD cards, “Memory
 
Stick Micro” media, microSD
 memory 
cards
Flash: Flash range (ISO sensitivity
 
(Recommended Exposure Index)
 set 
to 
Auto):
 
Approx. 0.4 m to 7.1 m
 
(1 ft 3 3/4 inches to 23 ft
 
3 5/8 inches) (W)
 
Approx. 1.5 m to 3.9 m
 
(4 ft 11 1/8 inches to 12 ft
 
9 5/8 inches) (T)
[Input and Output connectors]
HDMI connector: HDMI mini jack
Micro USB connector:
 USB 
communication
USB communication: Hi-Speed USB
 (USB 
2.0)
[Screen]
LCD screen:
 
7.5 cm (3.0 type) TFT drive
Total number of dots:
 
921 600 dots
[Power, general]
Power: Rechargeable battery pack
 NP-BG1, 
3.6 
V
 
NP-FG1 (sold separately), 3.6 V
 
AC Adaptor AC-UB10/UB10B,
 5 
V
Power consumption (during shooting):
 1.1 
W
Operating temperature: 0 °C to 40 °C
 
(32 °F to 104 °F)
Storage temperature: –20 °C to +60 °C
 
(–4 °F to +140 °F)
Dimensions (CIPA compliant):
 
106.6 mm × 61.9 mm × 34.6 mm
 
(4 1/4 inches × 2 1/2 inches ×
 
1 3/8 inches) (W/H/D)
Mass (CIPA compliant) (including NP-
BG1 battery pack, “Memory Stick
 Duo” 
media):
 
Approx. 254 g (9.0 oz)
Microphone: Stereo
Speaker: Monaural
Exif Print: Compatible
PRINT Image Matching III:
 Compatible
[Wireless LAN] 
(DSC-HX30/HX30V only)
Supported format: IEEE 802.11 b/g/n
AC Adaptor AC-UB10/UB10B
Power requirements: AC 100 V to
 
240 V, 50 Hz/60 Hz, 70 mA
Output voltage: DC 5 V, 0.5 A
Operating temperature: 0 °C to 40 °C
 
(32 °F to 104 °F)
Storage temperature: –20 °C to +60 °C
 
(–4 °F to +140 °F)
Dimensions:
 
Approx. 50 mm × 22 mm × 54 mm
 
(2 inches × 7/8 inches ×
 
2 1/4 inches) (W/H/D)
Mass:
 
For the USA and Canada: Approx.
 
48 g (1.7 oz)
 
For countries or regions other than
 
the USA and Canada: Approx. 43 g
 (1.5 
oz)
Rechargeable battery pack
NP-BG1
Used battery: Lithium-ion battery
Maximum voltage: DC 4.2 V
Nominal voltage: DC 3.6 V
Maximum charge voltage: DC 4.2 V
Maximum charge current: 1.44 A
Capacity:
 
typical: 3.4 Wh (960 mAh)
 
minimum: 3.3 Wh (910 mAh)
Design and specifications are subject to
change without notice.
The changed portions from
Ver. 1.2 are shown in blue.
Ver. 1.3 2012.09
DSC-HX20/HX20V/HX30/HX30V_L2
– 3 –
SAFETY-RELATED  COMPONENT  WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH 
MARK 
0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST 
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS 
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY 
SONY. 
ATTENTION AU  COMPOSANT  AYANT  RAPPORT 
À  LA  SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES 
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT 
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM-
PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT 
LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES 
SUPPLÉMENTS PUBLIÉS PAR SONY.
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
注意
電池の交換は,正しく行わないと破裂する恐れがあります。
電池を交換する場合には必ず同じ型名の電池又は同等品と
交換してください。
使用済み電池は,取扱指示に従って処分してください。
UNLEADED SOLDER
This unit uses unleaded solder.
Boards requiring use of unleaded solder are printed with the lead free 
mark (LF) indicating the solder contains no lead.
(Caution:  Some printed circuit boards may not come printed with the 
lead free mark due to their particular size.)
: LEAD FREE MARK
Be careful to the following points to solder or unsolder.
•   Set the soldering iron tip temperature to 350 °C approximately. 
If cannot control temperature, solder/unsolder at high temperature 
for a short time.
Caution:  The printed pattern (copper foil) may peel away if the 
heated tip is applied for too long, so be careful!  
Unleaded solder is more viscous (sticky, less prone to 
flow) than ordinary solder so use caution not to let solder 
bridges occur such as on IC pins, etc.
•   Be sure to control soldering iron tips used for unleaded solder and 
those for leaded solder so they are managed separately. Mixing un-
leaded solder and leaded solder will cause detachment phenomenon.
SAFETY  CHECK-OUT
After correcting the original service problem, perform the following 
safety checks before releasing the set to the customer.
1.  Check the area of your repair for unsoldered or poorly-soldered 
connections. Check the entire board surface for solder splashes and 
bridges.
2.  Check the interboard wiring to ensure that no wires are “pinched” 
or contact high-wattage resistors.
3.  Look for unauthorized replacement parts, particularly transistors, 
that were installed during a previous repair. Point them out to the 
customer and recommend their replacement.
4.  Look for parts which, through functioning, show obvious signs of 
deterioration. Point them out to the customer and recommend their 
replacement.
5.  Check the B+ voltage to see it is at the values specified.
6.  Flexible Circuit Board Repairing
 
•   Set the soldering iron tip temperature to 350 °C approximately.
 
•   Do not touch the soldering iron on the same conductor of the circuit 
board (within 3 times).
 
•   Be careful not to apply force on the conductor when soldering or 
unsoldering.
1.  注意事項をお守りください。
 
サービスのとき特に注意を要する個所については,キャビ
ネット,シャーシ,部品などにラベルや捺印で注意事項を
表示しています。これらの注意書き及び取扱説明書等の注
意事項を必ずお守り下さい。
2.  指定部品のご使用を
 
セットの部品は難燃性や耐電圧など安全上の特性を持った
ものとなっています。従って交換部品は,使用されていた
ものと同じ特性の部品を使用して下さい。特に回路図,部
品表に0印で指定されている安全上重要な部品は必ず指定
のものをご使用下さい。
3.  部品の取付けや配線の引きまわしはもとどおりに
 
安全上,チューブやテープなどの絶縁材料を使用したり,
プリント基板から浮かして取付けた部品があります。また
内部配線は引きまわしやクランパによって発熱部品や高圧
部品に接近しないよう配慮されていますので,これらは必
ずもとどおりにして下さい。
4.  サービス後は安全点検を
 
サービスのために取外したネジ,部品,配線がもとどおり
になっているか,またサービスした個所の周辺を劣化させ
てしまったところがないかなどを点検し,安全性が確保さ
れていることを確認して下さい。
5.  チップ部品交換時の注意
 
・  取外した部品は再使用しないで下さい。
 
・  タンタルコンデンサのマイナス側は熱に弱いため交換時
は注意して下さい。
6.  フレキシブルプリント基板の取扱いについて
 
・  半田こてのこて先温度は約350℃に設定してください。
 
・  同一パターンに何度もコテ先を当てないで下さい。(3回
以内)
 
・  パターンに力が加わらないよう注意して下さい。
サービス,点検時には次のことにご注意ください。
無鉛半田について
本機には無鉛半田が使用されています。
無鉛半田を使用している基板には,無鉛(Lead Free)を意味する
レッドフリーマークがプリントされています。
(注意: 基板サイズによっては,無鉛半田を使用していてもレッ
ドフリーマークがプリントされていないものがありま
す)
:レッドフリーマーク
無鉛半田は,下記の点に注意して使用してください。
・  半田こてのこて先温度は約350℃に設定してください。
温度調節が無理な場合は,高温短時間で作業を行ってくだ
さい。
注意:  半田こてを長く当てすぎると,基板のパターン(銅
箔)がはがれてしまうことがありますので,注意して
ください。また,従来の半田よりも粘性が強いため,
IC端子などが半田ブリッジしないように注意してく
ださい。
・  半田こてのこて先は,必ず無鉛半田用と有鉛半田用に分け
て管理してください。
無鉛半田と有鉛半田が混在すると剥離現象が発生してしま
います。
– ENGLISH –
– JAPANESE –
DSC-HX20/HX20V/HX30/HX30V_L2
1-1
1-1.  PRECAUTION ON REPLACING THE SY-325 BOARD
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATION DATA WRITE”.
RESTORE DATA
When you replace to the repairing board, get the data from the former one.
Start the Adjust Manual in the Adjust Station and perform “RESTORE DATA” to get the data. 
The data getting for this model is as follows.
• USB SERIAL No.
• Wide Limit Data
• Angular Velocity Sensor Sensitivity adjustment
• AWB standard data input & check, Color reproduction check
• Strobe adjustment
Deleting Network Settings
Before replacing the SY-325 board, delete the customer’s network settings.
Perform “NETWROK SETTING RESET” on the DATA tab of the Adjust Manual.
Regarding the PlayMemories Home
PlayMemories Home has been written in internal memory.
SY-325 board for service is supplied with written the PlayMemories Home.
USB SERIAL No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Start the Adjust Manual in the Adjust Station and execute the “USB SERIAL No. INPUT”.
Angular Velocity Sensor
When you replace to the repairing board, write down the sensitivity displayed on the angular velocity sensor (SE401).
Start the Adjust Manual in the Adjust Station and execute the “Angular velocity sensor sensitivity adj”.
P
Y
P
Y
Type A:
Type B:
SE401
SY-325 BOARD (SIDE A)
P: PITCH sensor sensitivity
Y: YAW sensor sensitivity
Note: The sensor sensitivity of SE401 of SY-325 board is written only repair parts.
1. SERVICE  NOTE
– ENGLISH –
Update of MAC Address
When a board that contains Wi-Fi has been replaced or when replacing a board that contains the main IC (CPU), the IC’s unique number (MAC ad-
dress) must be reloaded.
Perform the following procedure to reload the IC’s unique number (MAC address).
1.  Download the latest-version Adjust manual from the TISS homepage.
2.  Install the downloaded Adjust manual.
3.  Perform “Wireless LAN check” on the ADJUST tab.
4.  Perform the following operations for the unit.
   MENU →   (Settings) → Settings reset →   (Network Settings)
5.  Confirm that the displayed MAC address has been updated.
Applicable parts
•  SY-325 BOARD, COMPLETE (SERVICE)
•  SW-589 BOARD, COMPLETE
Note:  The LOAD AND WRITE function in ADJUSTMENT DATA BACKUP on the DATA tab in the Adjust manual overwrites all data of the unit.
 
Therefore, the MAC address updated during the above procedure is also overwritten.
Perform the above operations after all work has been done.
After the replacement and repair, the MAC address is changed, and thus the re-setting for connection devices is required. Accordingly, print out the 
flyer given at the manual and attach it to the set when returning the set to customer.
1-2.  ADDITION OF DESTINATION DATA FILE
If the Destination Data file included in the Adjust manual is old, “DESTINATION DATA WRITE” cannot be executed in some cases.
In that case, download a new Destination Data file from the TISS homepage according to the following procedure.
Note 1:  To perform Destination Data Write for this model, the Adjust manual of the DSC-WX50 series must have been installed.
 
Install the Adjust manual of the DSC-WX50 series in advance.
Note 2:  The actual image may differ from the image shown above.
1)  If the Destination Data file in the Adjust manual in use is old, the window shown in Fig. 1 is displayed.
 
Click the [OK] button.
 Fig. 
1
2)  The Destination Data Write window opens.
 
Check the version of the Destination Data file retained in the Adjust manual.
Destination Ver. window
The changed portions from
Ver. 1.5 are shown in blue.
Ver. 1.6 2013.03
Page of 34
Display

Sony DSC-HX20 / DSC-HX20V / DSC-HX30 / DSC-HX30V (serv.man2) Service Manual ▷ Download

  • DOWNLOAD Sony DSC-HX20 / DSC-HX20V / DSC-HX30 / DSC-HX30V (serv.man2) Service Manual ↓ Size: 7.38 MB | Pages: 34 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sony DSC-HX20 / DSC-HX20V / DSC-HX30 / DSC-HX30V (serv.man2) in PDF for free, which will help you to disassemble, recover, fix and repair Sony DSC-HX20 / DSC-HX20V / DSC-HX30 / DSC-HX30V (serv.man2) Digital Camera. Information contained in Sony DSC-HX20 / DSC-HX20V / DSC-HX30 / DSC-HX30V (serv.man2) Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.