DOWNLOAD Sony DSC-F505 Service Manual ↓ Size: 5.17 MB | Pages: 127 in PDF or view online for FREE

Adjust the burst level of the composite video signal output.

Mode

PLAY

Signal

Arbitrary

Measurement Point

Video terminal of AV OUT jack
(75

Ω

 terminated)

Measuring Instrument

Oscilloscope

Adjustment Page

F

Adjustment Address

66

Specified Value

A = 286 ± 5mV (NTSC)
A = 300 ± 5mV (PAL)

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: 5, address: F1, and set data: 04.

3)

Select page: F, address: 66, change the data and set the burst
level (A) to the specified value.

4)

Select page: 5, address: F1, and set data: 00.

5)

Select page: 0, address: 01, and set data: 00.

Confirm the Y level of the composite video signal output.

Mode

PLAY

Signal

Arbitrary

Measurement Point

Video terminal of AV OUT jack
(75

Ω

 terminated)

Measuring Instrument

Oscilloscope

Specified Value

A = 710 ± 20mV (NTSC)
A = 695 ± 20mV (PAL)

Adjusting method:
1)

Select page: 5, address: F1, and set data: 04.

2)

Check that the white (100 IRE) level (A) satisfies the specified value.

3)

Select page: 5, address: F1, and set data: 00.

A

H

A

H

A

White (100 IRE) 

H

Fig.5-1-10.

Fig.5-1-11.

Fig.5-1-12.

Adjust the sync level of the composite video signal output.

Mode

PLAY

Signal

Arbitrary

Measurement Point

Video terminal of AV OUT jack
(75

Ω

 terminated)

Measuring Instrument

Oscilloscope

Adjustment Page

F

Adjustment Address

65

Specified Value

A = 290 ± 5mV (NTSC)
A = 305 ± 5mV (PAL)

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: 5, address: F1, and set data: 04.

3)

Select page: F, address: 65, change the data and set the sync
level (A) to the specified value.

4)

Select page: 5, address: F1, and set data: 00.

5)

Select page: 0, address: 01, and set data: 00.

Before perform the camera system adjustments, check that the
specified values of “VIDEO SYSTEM ADJUSTMENT” are
satisfied.

For detecting the position of the lens iris, adjust the hall AMP gain
and offset.

Mode

STILL

Subject

Arbitrary

Measurement Point

Display data of page 1 (Note1)

Measuring Instrument

Adjustment remote commander

Adjustment Page

F

Adjustment Address

2E, 2F, 34, 35

Specified Value

13 to 17 during IRIS OPEN
7A to 7E during IRIS CLOSE

Displayed data of page 1 of the adjustment remote commander.

1 : 00 : XX

Display data

Check that the data of page: 6, address: 02 is “00”. If not, turn the
power of the unit OFF/ON.

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: 6, address: 94, and set data: 15.

3)

Select page: 6, address: 95, and set data: 7C.

4)

Select page: 6, address: 01, set data: 6D, and press the PAUSE
button of the adjustment remote commander. (The HALL
adjustment is performed and the adjustment data is stored in
page: F, address: 2E, 2F, 34 and 35.)

5)

Select page: 6, address: 02, and check that the data is “01”.

6)

Select page: 6, address: 01, set data: 00, and press the PAUSE
button.

Checking method:
1)

Select page: 0, address: 03, and set data: 03.

2)

Select page: 6, address: 01, set data: 01, and press the PAUSE
button.

3)

Select page: 1, and check that the display data (Note1) during
IRIS OPEN satisfies the specified value.

4)

Select page: 6, address: 01, set data: 03, and press the PAUSE
button.

5)

Select page: 1, and check that the display data during IRIS
CLOSE satisfies the specified value.

Processing after Completing Adjustments:
1)

Select page: 6, address: 01, set data: 00, and press the PAUSE
button.

2)

Select page: 6, address: 94, and set data: 00.

3)

Select page: 6, address: 95, and set data: 00.

4)

Select page: 0, address: 01, and set data: 00.

5)

Select page: 0, address: 03, and set data: 00.

Address

14

15

16

17

18

19

Data

1C

94

26

EC

13

B9

Address

1A

1B

1C

1D

1E

1F

Data

00

00

00

00

46

00

Address

20

21

22

23

24

25

Data

20

20

23

44

0A

00

The inner focus lens flange back adjustment is carried out
automatically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.

Mode

STILL

Subject

Siemens star chart with ND filter for
the minipattern box (Note1)

Measurement Point

Check operation on TV monitor

Measuring Instrument

Adjustment Page

F

Adjustment Address

14 to 25

Dark Siemens star chart.

Check that the data of page: 6, address: 02 is “00”. If not, turn the
power of the unit OFF/ON.

Preparations before adjustments:
The minipattern box is installed as shown in the following figure.

The attachment lenses are not used.

Specified voltage: The specified voltage varies according to the

minipattern box, so adjust the power supply
output voltage to the specified voltage
written on the sheet which is supplied with
the minipattern box.

Adjusting method:
1)

Install the minipattern box so that the distance between it and
the front of the lens of the camera is less than 3cm.

2)

Make the height of the minipattern box and the camcorder equal.

3)

Check that the output voltage of the regulated power supply is
the specified voltage ± 0.01Vdc.

4)

Select page: 0, address: 01, and set data: 01.

5)

Select page: 5, address: F1, and set data: FF.

6)

Check that the center of the Siemens star chart and center of
the exposure screen coincide.

7)

Check that the data of page: F, address: 14 to 25 is the initial
value (See table below).

8)

Select page: 6, address: 01, set data: 13, and press the PAUSE
button of the adjustment remote commander.

9)

Select page: 6, address: 01, set data: 27, and press the PAUSE
button.
(The adjustment data will be automatically input to page: F,
addresses: 14 to 25.)

10) Select page: 6, address: 02, and check that the data is changed

to “01”.

Processing after Completing Adjustments:
1)

Select page: 6, address: 01, set data: 00, and press the PAUSE
button.

2)

Select page: 5, address: F1, and set data: 00.

3)

Select page: 0, address: 01, and set data: 00.

4)

Perform “Flange Back Check”.

Fig.5-1-13.

Minipattern box

Below 3 cm

Camera

Table

Red (+)

Regulated power supply

Output voltage:  Specified voltage 

±

 0.01Vdc

Output current:  more than 3.5A

Black (–)

Yellow (SENS +)

White (SENS –)

Black (GND)

Need not connected

Mode

STILL

Subject

Siemens star
(2.0 m from the front of the lens)
(Luminance : approx. 200 lux)

Measurement Point

Check operation on TV monitor

Measuring Instrument

Specified Value

The lens is focused.

Checking method:
1)

Place the Siemens star 2.0m from the front of the lens.

2)

To open the IRIS, decrease the luminous intensity to the
Siemens star up to a point before noise appear on the image.

3)

Shoot the siemens star with the zoom TELE end.

4)

Turn on the auto focus

5)

Observe the TV monitor and check that the lens is focused.

6)

Select page: 0, address: 01, and set data: 01.

7)

Select page: 5, address: F1, and set data: FF.

8)

Select page: 6, address: 2C, and set data: 01.

9)

Shoot the siemens star with the zoom WIDE end.

10) Observe the TV monitor and check that the lens is focused.

Processing after Completing Adjustments:
1)

Select page: 6, address: 2C, and set data: 00.

2)

Select page: 5, address: F1, and set data: 00.

3)

Select page: 0, address: 01, and set data: 00.

The inner focus lens flange back adjustment is carried out
automatically. In whichever case, the focus will be deviated during
auto focusing/manual focusing.

Mode

STILL

Subject

Flange back adjustment chart
(2.0 m from the front of the lens)
(Luminance: 350 ± 50 lux)

Measurement Point

Check operation on TV monitor

Measuring Instrument

Adjustment Page

F

Adjustment Address

14 to 25

Check that the data of page: 6, address: 02 is “00”. If not, turn the
power of the unit OFF/ON.

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: 5, address: F1, and set data: FF.

3)

Check that the center of the chart for the flange back adjustment
and center of the exposure screen coincide.

4)

Check that the data of page: F, address: 14 to 25 is the initial
value (See table below).

5)

Select page: 6, address: 01, set data: 13, and press the PAUSE
button of the adjustment remote commander.

6)

Select page: 6, address: 01, set data: 15, and press the PAUSE
button.
(The adjustment data will be automatically input to page: F,
addresses: 14 to 25.)

7)

Select page: 6, address: 02, and check that the data is changed
to “01”.

Processing after Completing Adjustments:
1)

Select page: 6, address: 01, set data: 00, and press the PAUSE
button.

2)

Select page: 5, address: F1, and set data: 00.

3)

Select page: 0, address: 01, and set data: 00.

4)

Perform “Flange Back Check”.

14

15

16

17

18

19

1C

94

26

EC

13

B9

1A

1B

1C

1D

1E

1F

00

00

00

00

46

00

20

21

22

23

24

25

20

20

23

44

0A

00