DOWNLOAD Sony DSC-F505 Service Manual ↓ Size: 5.17 MB | Pages: 127 in PDF or view online for FREE

Mode

STILL

Subject

Clear chart
(25 cm from the front of the lens)
(Note1)

Measurement Point

Display data of page: 6, address: 55

Measuring Instrument

Adjustment remote commander

Specified Value

00

Check that there are no dust, no dirt and no reflection on the clear
chart.

Any subject other than the clear chart should not be in the screen.

This adjustment should be carried out upon completion of
“CCD Black Defect Compensation”.

Checking method:
1)

Turn the power of the unit OFF and then ON.

2)

Wait until the camera picture appear on the screen.

3)

Select page: 0, address: 01, and set data: 01.

4)

Select page: 5, address: F1, and set data: FF.

5)

Select page: F, address: DF, after noting down the data, set
data: 5A, and press PAUSE button.

6)

Select page: 6, address: 2C, and set data: 01.

7)

Select page: 6, address: 90, and set data: 00.

8)

Select page: 6, address: 91, and set data: 03.

9)

Select page: 6, address: 92, and set data: 00.

10) Select page: 6, address: 93, and set data: 00.
11) Select page: 6, address: 01, and set data: 79.
12) Select page: 6, address: 30, set data: 07, and wait for four

seconds.

13) Select page: 6, address: 01, set data: 89, and press the PAUSE

button.

14) Select page: 6, address: 02, and check that the data changes to

“01”.

15) Select page: 6, address: 55, and check that the data is “00”. (If

the data is other than “00”, black defect compensation has
errors.)

Processing after Completing Adjustments:
1)

Select page: F, address: DF, set the data noted down at step 5),
and press the PAUSE button.

2)

Select page: 6, address: 01, and set data: 00, and press the
PAUSE button of the adjustment remote commander.

3)

Select page: 6, address: 2C, and set data: 00.

4)

Select page: 6, address: 30, and set data: 00.

5)

Select page: 6, address: 91, and set data: 00.

6)

Select page: 5, address: F1, and set data: 00.

7)

Select page: 0, address: 01, and set data: 00.

Mode

STILL

Subject

Clear chart
(25 cm from the front of the lens)
(Note1)

Measurement Point

Display data of page: 6, address: 55

Measuring Instrument

Adjustment remote commander

Adjustment Page

7

Adjustment Address

88 to A3

Specified value

Data 

< 7F: OK, Data > 80: NG

Check that there are no dust, no dirt and no reflection on the clear
chart.

Any subject other than the clear chart should not be in the screen.

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: 5, address: F1, and set data: FF.

3)

Select page: F, address: DE, after noting down the data, set
data: 14, and press the PAUSE button of the adjustment remote
commander.

4)

Select page: F, address: E3, after noting down the data, set data:
28, and press the PAUSE button.

5)

Select page: 6, address: 01, set data: 8B, and press the PAUSE
button.
(The CCD white defect compensation is performed and the
adjustment data is stored in page: 7, address: 88 to A3.)

6)

Select page: 6, address: 02, and check that the data changes to
“01”.

7)

Select page: 6, address: 55, and check the data satisfies specified
value.

Processing after Completing Adjustments:
1)

Select page: F, address: DE, set the data noted down at step 3),
and press the PAUSE button.

2)

Select page: F, address: E3, set the data noted down at step 4),
and press the PAUSE button.

3)

Select page: 6, address: 01, and set data: 00, and press the
PAUSE button of the adjustment remote commander.

4)

Select page: 5, address: F1, and set data: 00.

5)

Select page: 0, address: 01, and set data: 00.

Mode

STILL

Subject

Clear chart
(25 cm from the front of the lens)
(Note1)

Measurement Point

Display data of page: 6, address: 55

Measuring Instrument

Adjustment remote commander

Specified Value

00

Check that there are no dust, no dirt and no reflection on the clear
chart.

Any subject other than the clear chart should not be in the screen.

This adjustment should be carried out upon completion of
“CCD White Defect Compensation”.

Checking method:
1)

Turn the power of the unit OFF and then ON.

2)

Wait until the camera picture appear on the screen.

3)

Select page: 0, address: 01, and set data: 01.

4)

Select page: 5, address: F1, and set data: FF.

5)

Select page: F, address: DE, after noting down the data set data:
0A, and press the PAUSE button.

6)

Select page: F, address: E3, after noting down the data, set data:
80, and press the PAUSE button.

7)

Turn the power of the unit OFF and wait for four seconds.

8)

Turn the power of the unit ON.

9)

Select page: 0, address: 01, and set data: 01.

10) Select page: 6, address: 55, and check that the data is “00”. (If

the data is other than “00”, white defect compensation has
errors.)

11) Select page: F, address: E3, set data: A0, and press the PAUSE

button.

12) Select page: 6, address: 01, set data: 87, and press the PAUSE

button.

13) Select page: 6, address: 02, and check that the data changes to

“01”.

14) Select page: 6, address: 55, and check that the data is “00”. (If

the data is other than “00”, black defect compensation has
errors.)

Processing after Completing Adjustments:
1)

Select page: F, address: DE, set the data noted down at step 5),
and press the PAUSE button.

2)

Select page: F, address: E3, set the data noted down at step 6),
and press the PAUSE button.

3)

Select page: 6, address: 01, and set data: 00, and press the
PAUSE button of the adjustment remote commander.

4)

Select page: 5, address: F1, and set data: 00.

5)

Select page: 0, address: 01, and set data: 00.

Before perform the LCD system adjustments, check that the specified
values of “VIDEO SYSTEM ADJUSTMENT” are satisfied.

The back light (fluorescent tube) is driven by a high voltage AC
power supply. Therefore, do not touch the back light holder to
avoid electrical shock.

When replacing the LCD unit, be careful to prevent damages
caused by static electricity.

Set the LCD BRIGHT to the center.

Most of the measuring points for adjusting the LCD system are
concentrated in CN002 of the Control Switch Block (FK).
Connect the Measuring Instruments via the CPC-9 jig (J-6082-393-
C, Note4). To operate the adjustment remote commander, connect
the power supply terminal of CPC-9 jig to the DC power supply
(6.0 to 7.2Vdc).
The following table shows the Pin No. and signal name of CN002.

The old CPC-9 jig (Parts code: J-6082-393-B) cannot be used,
because it cannot operate the adjustment remote commander.

Table 5-1-7.

1

2

3

4

5

6

7

8

9

NC

NC

NC

REG GND

NC

SYS V

HSY

PANEL COM

VG

10

11

12

13

14

15

16

17

18

HI UNREG

LANC IN

LANC OUT

NC

RF7

TXD

RXD

RESET

V

DD

Fig.5-1-19.

Control switch block (FK)
(CN002)

1

18

Note : Don't use the 12 pin flexible board of CPC-9 jig.
           It causes damage to the unit

CPC cover

Slide the Release knob in the direction of arrow 

A

.

To open the Battery lid.

Two claws

CPC-9 jig
(18p flexible board)

A

Release knob

Mode

PLAY

Signal

Arbitrary

Adjustment Page

D

Adjustment Address

1C, 1D, 80 to 88, 8D to 8F

Adjusting method:
1)

Select page: 0, address:01, and set data: 01.

2)

Select page: D, and input the data in the following table.

To write in the non-volatile memory (EEPROM), press the
PAUSE button of the adjustment remote commander each time
to set the data.

3)

Select page: 0, address:01, and set data: 00.

1C

1D

80

81

82

83

84

85

86

87

88

8D

8E

8F

Fixed data

Fixed data

Bright adj.

Color adj.

White balance adj.

White balance adj.

Contrast adj.

D range adj.

V-COM level adj.

VCO adj. (NTSC)

Fixed data (PAL)

V-COM adj.

VCO adj. (PAL)

Fixed data (NTSC)

Fixed data

Fixed data

00

2C

BC

80

B9

B7

BE

C8

7C

50

74

50

13

11

Set the D range of the RGB decoder used to drive the LCD to the
specified value. If deviated, the LCD screen will become blackish
or saturated (whitish).

Mode

PLAY

Signal

Arbitrary

Measurement Point

Pin 9 of CN002 (VG)
External trigger: Pin 8 of CN002
(PANEL COM)

Measuring Instrument

Oscilloscope

Adjustment Page

D

Adjustment Address

85

Specified Value

A = 3.62 ± 0.05V

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: 5, address: F1, set data: 03.

3)

Select page: D, address: 85, change the data and set the voltage
(A) between the reversed waveform pedestal and non-reversed
waveform pedestal to the specified value.

4)

Press the PAUSE button of the adjustment remote commander.

5)

Select page: 5, address: F1, set data: 00.

6)

Select page: 0, address: 01, and set data: 00.

Fig.5-1-20.

A

2H 

Pedestal 

Pedestal

Set the VCO free-run frequency. If deviated, the LCD screen will
be blurred.

Mode

PLAY

Signal

Arbitrary

Measurement Point

Pin 7 of CN002 (HSY)

Measuring Instrument

Frequency counter

Adjustment Page

D

Adjustment Address

87 (NTSC)
8D (PAL)

Specified Value

f = 15734 ± 30Hz (NTSC)
f = 15750 ± 30Hz (PAL) (Note)

Adjusting method:
1)

Select page: 0, address: 01, and set data: 01.

2)

Select page: 5, address: F0, set data: 01.

3)

For NTSC model, select page: D, address: 87, change the data
and set the frequency (f) to the specified value.
For PAL model, select page: D, address: 8D, change the data
and set the frequency (f) to the specified value.

4)

Press the PAUSE button of the adjustment remote commander.

5)

Select page: 5, address: F0, set data: 00.

6)

Select page: 0, address: 01, and set data: 00.

This specified value is the adjustment value for the NTSC
mode.
If using for the PAL mode, be sure to switch VIDEO OUT
to the NTSC mode at menu setup before performing
adjustments. After adjusting, be sure to switch to the PAL
mode.