Sony XAV-701HD Service Manual ▷ View online
XAV-701HD
21
3-19. DC FAN (25X25) (M801), MAIN BOARD
3-20. MOTOR ASSY
2 connector
(CN803)
7 Remove the
solder.
8 ground sheet (TU)
or
HD plate (GND)
9 MAIN board
D401
6 thermal conductive
pad
T8
thermal conductive
pad T8
pad T8
MAIN board
CN803
1 fuse (blade type) (auto fuse)
(F801)
5 DC fan
(25
u 25)
(M801)
:LUHVHWWLQJ
7KHUPDOFRQGXFWLYHSDG7VHWWLQJ
NG
OK
3 screw
(PTT2.6
u 14)
3 screw
(PTT2.6
u 14)
DC fan (25
u 25) (M801)
D401
D401
D401
thermal conductive
pad T8
pad T8
thermal conductive
pad T8
pad T8
thermal conductive
pad T8
pad T8
guide line
thermal conductive
pad T8
pad T8
thermal conductive
pad T8
pad T8
thermal conductive
pad T8
pad T8
D401
D401
D401
guide line
4 sheet (GPS wire)
or
filament
filament
tape
Note
2: Sheet (GPS wire) has
been changed into
filament tape from the
midway of production.
sheet (GPS wire) or
filament tape
filament tape
4 screw
(PTT2.6
u 6)
5 bracket (front7)
6 motor assy
1 screw
(PTT2.6
u 6)
1 screw
(PTT2.6
u 6)
2 screw
(Z
S2.6
u 4)
2 screw
(Z
S2.6
u 4)
3 chassis (L)
Ver. 1.2
Note 1: When the complete MAIN board is replaced, the destination setting is necessary. Refer to
“NOTE THE MAIN BOARD OR SYSTEM CONTROLLER (IC502) REPLACING” on page 5.
XAV-701HD
22
3-21. MONITOR OPEN/CLOSE BLOCK (DB-W07)
1 screw
(PTT2.6
u 6)
8 screw (T)
8 three screws (T)
9 MOTOR board
3 bracket (back)
5 flexible flat cable (20 core)
(FFC2)
(CN7002)
(CN7002)
7 connector
(CN7001)
flexible flat cable (20 core)
(FFC2)
(FFC2)
4 tape
6 tape
tape
tape
guide line
guide line
MOTOR board
2 claw
2 claw
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
flexible flat cable
flexible flat cable
flexible flat cable
connector
connector
NG
OK
NG
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
connector
connector
connector
connector
connector
NG
OK
NG
)OH[LEOHIODWFDEOHFRUH))&VHWWLQJ
,QVWDOOHGSRVLWLRQ
,QVWDOOHGSRVLWLRQ
:LUHVHWWLQJ
Note 1: When you install the flexible flat cable, please install them
correctly. There is a possibility that this machine damages
when not correctly installing it.
Note 2: When you install the connector, please install them correctly.
There is a possibility that this machine damages when not
correctly installing it.
0 monitor open/close block
(DB-W07)
monitor open/close motor
(M7001)
(M7001)
XAV-701HD
23
3-22. DVD MECHANISM DECK (MG-613XF-187)
3-23. SERVO BOARD
3 shield (613S)
1 two precision screws
(P1.7
u 2.2)
5 bracket (DVD)
6 DVD mechanism deck
(MG-613XF-187)
4 screw
(PTT2.6
u 5) (for MG-613XF-187)
(PTT2.6
u 6) (for MG-614D-189)
2 screw
(PTT2.6
u 5) (for MG-613XF-187)
(PTT2.6
u 6) (for MG-614D-189)
(MG-613XF-187 only)
– DVD mechanism deck block (Bottom view) –
1 Remove the two solders
of loading motor wire.
8 SERVO board
SERVO board
RED
WHITE
5 three toothed lock screws
(Z M1.7
u 2.5)
7 flexible flat cable (60 core)
(CN10)
6 Remove the SERVO board
in the direction of the arrow.
4 sled motor flexible board
(CN1)
2 Remove the three solders
of SENSOR board wire.
SERVO board
RED
WHITE
BLACK
3 OP flexible board (CN2)
Note: When disconnecting the OP flexible board from
of the connector. Be sure to refer to “NOTE FOR
FLEXIBLE BOARD OF THE OPTICAL PICK-UP”
of the servicing notes (See page 6).
Ver. 1.2
Note: Refer to SUPPLEMENT-1 for discrimination of the DVD
mechanism deck (MG-613XF-187 or MG-614D-189).
XAV-701HD
24
3-24. CHASSIS (T612Z) SUB ASSY, SENSOR BOARD
3-25. CHASSIS (OP, ZA) COMPLETE ASSY (OP1)
1 two precision screws
(P1.7
u 2.2)
4 chassis (T612Z) sub assy
1 two precision screws
(P1.7
u 2.2)
2 claw
3 claw
6 SENSOR borad
5 Remove the three solders
of SENSOR board wire.
RED
WHITE
BLACK
xxxxxxxxxxx
A
5
6 two coil springs
(damper)
9 chassis (OP, ZA) complete assy
(OP1)
8 label (S)
7 compression spring
(damper,
Z)
2 sled motor flexible
board (CN1)
3 tension spring (KF)
tension spring (KF)
0HWKRGRILQVWDOOLQJWHQVLRQVSULQJ.)
4 Turn the gear (RA1) fully
in the direction of arrow A.
Hang in order of
A, B by pay
attention spring of direction.
A
B
±%RWWRPYLHZ±
1 OP flexible board (CN2)
Note:
When disconnecting the OP flexible board
from of the connector. Be sure to refer to
“NOTE FOR FLEXIBLE BOARD OF THE
OPTICAL PICK-UP” of the servicing notes
(See page 6).
Click on the first or last page to see other XAV-701HD service manuals if exist.