DOWNLOAD Sony WX-800UI Service Manual ↓ Size: 7.44 MB | Pages: 52 in PDF or view online for FREE

4.  The resetting operation is executed by pressing the [SOURCE 

 OFF] button for 1 second after the setting ends, and the unit 

returns to the normal condition.

 

(Displayed characters/values in the following fi gure are ex-
ample)

1-2.  Display in Destination Setting Mode
(Displayed characters/values in the following fi gure are example)

1.  Rotate the control dial, and select the alphanumeric character 

of “0 to F”.

2.  The digit advances by pressing the [PUSH ENTER/MENU] or 

[

M>

 SEEK+] button.

  The digit returns by pressing the [MODE  ] or [SEEK– 

.m

] button.

3.  The setting is completed by pressing the [PUSH ENTER/

MENU] button, then the display turns off, the initialization op-
eration is done, and the display returns to the clock display.

•  Method of operation by remote commander
 

 

Note: The model to which the remote commander is not attached can 

also be operated by using the remote commander.

1. Press the [V] or [v] button, and select the alphanumeric char-

acter of “0 to F”.

2.  The digit advances by pressing the [b] or [ENTER] button.

 

The digit returns by pressing the [B] button.

3.  The setting is completed by pressing the [ENTER] button, then 

the display turns off, the initialization operation is done, and 
the display returns to the clock display.

AEP, UK (EUR)

0

8

8

0

1

1

Russian (RU2)

0

9

8

0

1

7

E, Australian (E)

0

C

B

0

1

0

Indian (IN)

0

C

9

0

1

0

– Continued on next page –

2. Confi rmation After Destination Setting
Execute the following operation after completing the destination 
setting, and confi rm a correct destination was set.

Destination setting checking method:
1.  In the state of source off (the clock is displayed on the liquid 

crystal display), enter the test mode by pressing the buttons 
in order of the [  4] t [5] t [PAUSE 6] (press only the 

[PAUSE 6] button for two seconds).

 

(Displayed characters/values in the following fi gure are ex-
ample)

2.  In the state in which the system controller version is displayed 

on the liquid crystal display (refer to following fi gure), enter 
the destination setting value display mode by pressing the 
[DSPL  SCRL ] button twice.

 

(Displayed characters/values in the following fi gure are ex-
ample)

3. Confi rm the alphanumeric character of 12 digits of in liquid 

crystal display is an value correctly input.

 

(Displayed characters/values in the following fi gure are ex-
ample)

4.  The resetting operation is executed by pressing the [SOURCE 

 OFF] button for 1 second after the confi rming ends, and the 

unit returns to the normal condition.

 

(Displayed characters/values in the following fi gure are ex-
ample)

MODEL  IDENTIFICATION
Distinguish by Part No. on the bottom side of the main unit.

4-575-524-0[]

AEP and UK models (EUR)

4-575-525-0[]

Russian model (RU2)

4-575-526-0[]

E and Australian models (E)

4-575-527-0[]

Indian model (IN)

TEST  DISCS
Use following TEST DISC (for CD) when this unit confi rms the 
operation and checks it.

Part No.

   

Description

3-702-101-01 DISC 

(YEDS-18), 

TEST

4-225-203-01 DISC 

(PATD-012), 

TEST

NOTE  OF  PERFORMING  THE  OPERATION  CHECK
When performing the operation check in the state that is removed 
the CD mechanism deck from the main unit, it is necessary to use 
a long fl exible fl at cable.
When performing the operation check, use following fl exible fl at 
cable.

Part No.

   

Description

1-846-819-31 

CABLE FLEXIBLE FLAT (27 CORE)

(Length: 150 mm)

NOTE  OF  REPLACING  THE  IC001,  IC503,  IC804  AND  
IC1009  ON  THE  MAIN  BOARD
IC001, IC503, IC804 and IC1009 on the MAIN board cannot re-
place with single. When these parts are damaged, replace the com-
plete mounted board.

NOTE  FOR  REPLACING  OF  THE  USB  CONNECTOR 
(CN902)  AND  THE  AUX  JACK (J901)
To replace the USB connector and AUX jack requires alignment.
1.  Insert the USB connector and AUX jack into the front panel.
2.  Place the KEY board on the front panel and align the terminals 

of the USB connector and AUX jack with the holes in the KEY 
board.

3.  Solder six terminals of the USB connector and three terminals 

of the AUX jack.

You can cancel the demonstration display which 
appears when the source is off and the clock is 
displayed.

1

Press MENU, rotate the control dial to 
select [SET GENERAL], then press it.

2

Rotate the control dial to select [SET 
DEMO], then press it.

3

Rotate the control dial to select [SET 
DEMO-OFF], then press it.

The setting is complete.

4

Press  

(back) 

twice.

The display returns to normal reception/play 
mode.

This section is extracted 
from operating instruction.

Run all ground (earth) leads to a common 
ground (earth) point.
Do not get the leads trapped under a screw, or 
caught in moving parts (e.g., seat railing).
Before making connections, turn the car ignition 
off to avoid short circuits.
Connect the power supply lead 

 to the unit and 

speakers before connecting it to the auxiliary 
power connector.
Be sure to insulate any loose unconnected leads 
with electrical tape for safety.

Choose the installation location carefully so that 
the unit will not interfere with normal driving 
operations.
Avoid installing the unit in areas subject to dust, 
dirt, excessive vibration, or high temperature, 
such as in direct sunlight or near heater ducts.
Use only the supplied mounting hardware for a 
safe and secure installation.

Note on the power supply lead (yellow)
When connecting this unit in combination with other 
stereo components, the amperage rating of the car 
circuit to which the unit is connected must be higher 
than the sum of each component’s fuse amperage 
rating.

Adjust the mounting angle to less than 45°.

*1 Not supplied
*2 Speaker impedance: 4 – 8 Ω × 4
*3 RCA pin cord (not supplied)
*4 Depending on the type of car, use an adaptor for a 

wired remote control (not supplied).

*5 Depending on the type of car, use an adaptor (not 

supplied) if the antenna (aerial) connector does not 
fit.

*6 AUDIO OUT can be switched to SUB or REAR.

If you have a power antenna (aerial) without a relay 
box, connecting this unit with the supplied power 
supply lead 

 may damage the antenna (aerial).

1

Rear speaker 
(right)

Purple

2

Purple/black 
striped

3

Front speaker 
(right)

Gray

4

Gray/black striped

5

Front speaker 
(left)

White

6

White/black 
striped

7

Rear speaker 
(left)

Green

8

Green/black 
striped

12

continuous power 
supply

Yellow

13

power antenna (aerial) /
power amplifier control 
(REM OUT)

Blue/white striped

15

switched power supply

16

ground (earth)

Black

Red

You can use a subwoofer without a power amplifier 
when it is connected to a rear speaker cord.

Preparation of the rear speaker cords is required.
Use a subwoofer with an impedance of 4 to 8 ohms, 
and with adequate power handling capacities to 
avoid damage.

When the yellow power supply lead is connected, 
power will always be supplied to the memory 
circuit even when the ignition switch is turned off.

Before connecting the speakers, turn the unit off.
Use speakers with an impedance of 4 to 8 ohms, 
and with adequate power handling capacities to 
avoid damage.

Make sure your car’s auxiliary power connector, and 
match the connections of cords correctly 
depending on the car.

12

continuous power 
supply

Yellow

15

switched power supply

Red

12

switched power supply 

Yellow

15

continuous power 
supply

Red

After matching the connections and switching 
power supply leads correctly, connect the unit to 
the car’s power supply. If you have any questions 
and problems connecting your unit that are not 
covered in this manual, consult the car dealer.