Sony MDX-F5800 Service Manual ▷ View online
5
MDX-F5800
AUDIO OUT REAR
AUDIO OUT FRONT
BUS AUDIO IN
BUS CONTROL IN
BUS CONTROL IN
BUS AUDIO IN
2
A
B
Source selector*
Sélecteur de source*
Selector de fuente*
Sélecteur de source*
Selector de fuente*
XA-C30
* not supplied
(US model)
Connection example (
2
)
Notes (2-A)
• Be sure to connect the ground lead before connecting
• Be sure to connect the ground lead before connecting
the amplifier.
• If you connect an optional power amplifier and do not
use the built-in amplifier, the beep sound will be
deactivated.
deactivated.
Tip (2-B-
)
For connecting two or more MD/CD changers, the source
selector XA-C30 (optional) is necessary.
selector XA-C30 (optional) is necessary.
Connection diagram (
3
)
1
To a metal surface of the car
First connect the black ground lead, then connect
the yellow and red power input leads.
the yellow and red power input leads.
2 To the power antenna control lead or power
supply lead of antenna booster amplifier
Notes
• It is not necessary to connect this lead if there is no
• It is not necessary to connect this lead if there is no
power antenna or antenna booster, or with a
manually-operated telescopic antenna.
manually-operated telescopic antenna.
• When your car has a built-in FM/AM antenna in
the rear/side glass, see “Notes on the control and
power supply leads.”
power supply leads.”
3
To AMP REMOTE IN of an optional power
amplifier
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
any other system may damage the unit.
4
To the interface cable of a car telephone
5
To the +12 V power terminal which is energized
in the accessory position of the ignition key
switch
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the +12
• If there is no accessory position, connect to the +12
V power (battery) terminal which is energized at
all times.
Be sure to connect the black ground lead to a
metal surface of the car first.
all times.
Be sure to connect the black ground lead to a
metal surface of the car first.
• When your car has a built-in FM/AM antenna in
the rear/side glass, see “Notes on the control and
power supply leads.”
power supply leads.”
6
To the +12 V power terminal which is energized
at all times
at all times
Be sure to connect the black ground lead to a metal
surface of the car first.
surface of the car first.
Notes on the control and power supply leads
• The power antenna control lead (blue) supplies +12 V
• The power antenna control lead (blue) supplies +12 V
DC when you turn on the tuner.
• When your car has built-in FM/AM antenna in the rear/
side glass, connect the power antenna control lead
(blue) or the accessory power input lead (red) to the
power terminal of the existing antenna booster. For
details, consult your dealer.
(blue) or the accessory power input lead (red) to the
power terminal of the existing antenna booster. For
details, consult your dealer.
• A power antenna without a relay box cannot be used
with this unit.
Memory hold connection
When the yellow power input lead is connected, power
will always be supplied to the memory circuit even when
the ignition switch is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and
When the yellow power input lead is connected, power
will always be supplied to the memory circuit even when
the ignition switch is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and
with adequate power handling capacities to avoid its
damage.
damage.
• Do not connect the speaker terminals to the car
chassis, or connect the terminals of the right speakers
with those of the left speaker.
with those of the left speaker.
• Do not connect the ground lead of this unit to the
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active
• Connect only passive speakers. Connecting active
speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.
terminals may damage the unit.
• To avoid a malfunction, do not use the built-in speaker
leads installed in your car if the unit shares a common
negative (–) lead for the right and left speakers.
negative (–) lead for the right and left speakers.
• Do not connect the unit’s speaker leads to each other.
Note on connection
If speaker and amplifier are not connected correctly,
“FAILURE” appears in the display. In this case, make sure
the speaker and amplifier are connected correctly.
Note on connection
If speaker and amplifier are not connected correctly,
“FAILURE” appears in the display. In this case, make sure
the speaker and amplifier are connected correctly.
L
R
BUS AUDIO IN
AUDIO OUT
FRONT
AUDIO OUT
REAR
*
2
BUS
CONTROL IN
REMOTE
IN
3
Source selector
(not supplied)
XA-C30
AMP REM
Max. supply current 0.3 A
Fuse (10 A)
Blue/white striped
Supplied with the MD/CD changer
3
from car antenna
5
6
4
ANT REM
4
ATT
1
*
1
Red
Yellow
Black
Blue
White
Green
Purple
White/black striped
Gray/black striped
Green/black striped
Gray
Left
Right
Left
Right
Light blue
Max. supply current 0.1 A
*
3
2
Purple/black striped
*
1
Supplied with XA-C30
*
1
RCA pin cord (not supplied)
*
2
AUDIO OUT can be switched to REAR
or SUB.
For details, see the supplied operating
instructions.
or SUB.
For details, see the supplied operating
instructions.
*
3
Insert with the cord downwards.
6
MDX-F5800
182 m
m
53 m
m
4
1
2
3
3
1
1
Dashboard
5
1
2
3
5
5
c
c
c
1
Face the hook inwards.
Claws
Orient the release key
correctly.
correctly.
6
A
TOYOTA
to dashboard/center console
Bracket
Bracket
B
NISSAN
2
2
to dashboard/center console
Bracket
Bracket
2
2
Existing parts supplied with your car
7
A
B
max. size
5
5
× 8 mm
(
7
/
32
×
11
/
32
in)
Dimensions
max. size
5
5
× 8 mm
(
7
/
32
×
11
/
32
in)
Dimensions
max. size
5
5
× 8 mm
(
7
/
32
×
11
/
32
in)
Dimensions
max. size
5
5
× 8 mm
(
7
/
32
×
11
/
32
in)
Dimensions
1
2
Existing parts supplied with your car
A
B
c
7
MDX-F5800
How to detach and attach the
front panel (
front panel (
7
)
Before installing the unit, detach the front
panel.
panel.
7
-A To detach
Before detaching the front panel, be sure to
press (OFF). Press (OPEN), then slide the front
panel to the right side, and pull out the left side.
press (OFF). Press (OPEN), then slide the front
panel to the right side, and pull out the left side.
7
-B To attach
Place the hole A in the front panel onto the
spindle B on the unit as illustrated, then push
the left side in.
spindle B on the unit as illustrated, then push
the left side in.
Warning when installing in a car
without ACC (accessory)
position on the ignition key
switch
without ACC (accessory)
position on the ignition key
switch
After turning off the ignition, be sure to
press and hold
press and hold
(OFF)
on the unit until the
display disappears.
Otherwise, the display does not turn off and this
causes battery drain.
causes battery drain.
RESET button
When the installation and connections are
completed, be sure to press the RESET button
with a ball-point pen, etc., after detaching the
front panel.
completed, be sure to press the RESET button
with a ball-point pen, etc., after detaching the
front panel.
Precautions
•Choose the installation location carefully so
that the unit will not interfere with normal
driving operations.
driving operations.
•Avoid installing the unit in areas subject to
dust, dirt, excessive vibration, or high
temperatures, such as in direct sunlight or
near heater ducts.
temperatures, such as in direct sunlight or
near heater ducts.
•Use only the supplied mounting hardware for
a safe and secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 45°.
Removing the protection collar
and the bracket (
and the bracket (
4
)
Before installing the unit, remove the
protection collar 3 and the bracket 1 from
the unit.
protection collar 3 and the bracket 1 from
the unit.
1
Remove the protection collar 3.
1 Engage the release keys 5 together with
1 Engage the release keys 5 together with
the protection collar 3.
2 Pull out the release keys 5 to remove the
protection collar 3.
2
Remove the bracket 1.
1 Insert both release keys 5 together
1 Insert both release keys 5 together
between the unit and the bracket 1 until
they click.
they click.
2 Pull down the bracket 1, then pull up
the unit to separate.
Mounting example (
5
)
Installation in the dashboard
Notes
• Bend these claws outward for a tight fit, if
• Bend these claws outward for a tight fit, if
necessary (5-2).
• Make sure that the 4 catches on the protection
collar 3 are properly engaged in the slots of the
unit (5-3).
unit (5-3).
Mounting the unit in a
Japanese car (
Japanese car (
6
)
You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult
your Sony dealer.
makes of Japanese cars. In such a case, consult
your Sony dealer.
Note
To prevent malfunction, install only with the
supplied screws 2.
To prevent malfunction, install only with the
supplied screws 2.
8
MDX-F5800
2
A
B
AUDIO OUT REAR
AUDIO OUT FRONT
BUS AUDIO IN
BUS CONTROL IN
BUS CONTROL IN
BUS AUDIO IN
Source selector *
XA-C30
* not supplied
(AEP, UK models)
L
R
5
7
4
8
1
3
5
7
2
4
6
8
A
B
AMP REM
ATT
AUDIO OUT
REAR
*
3
BUS
CONTROL IN
AUDIO OUT
FRONT
BUS AUDIO IN
REMOTE
IN
Source selector
(not supplied)
(not supplied)
XA-C30
Supplied with the MD/CD changer
*
2
5
from car aerial
*
1
Fuse (10 A)
7
Light blue
Blue/white striped
*
4
Max. supply current 0.3 A
Yellow
Blue
continuous power supply
power aerial control
7
8
4
5
Red
Black
switched power supply
earth
Positions 1, 2, 3 and 6 do not have pins.
1
2
3
4
Speaker, Rear, Right
Speaker, Rear, Right
Speaker, Front, Right
Speaker, Front, Right
5
6
7
8
Speaker, Front, Left
Speaker, Front, Left
Speaker, Rear, Left
Speaker, Rear, Left
Purple
White
Grey
+
–
+
–
+
–
+
–
from the car’s speaker connector
from the car’s power connector
See “Power connection diagram” on the reverse side for details.
3
Negative polarity positions 2, 4, 6, and 8 have striped leads.
Green
Supplied with XA-C30
*
2
*
1
Note for the aerial connecting
If your car aerial is an ISO (International
Organisation for Standardisation) type, use the
supplied adaptor 5 to connect it.
First connect the car aerial to the supplied
adaptor, then connect it to the aerial jack of the
master unit.
If your car aerial is an ISO (International
Organisation for Standardisation) type, use the
supplied adaptor 5 to connect it.
First connect the car aerial to the supplied
adaptor, then connect it to the aerial jack of the
master unit.
*
2
RCA pin cord (not supplied)
*
3
AUDIO OUT can be switched REAR or SUB.
For details, see the Operating Instructions
manual.
For details, see the Operating Instructions
manual.
*
4
Insert with the cord downwards
Connection example (
2
)
Notes (2-A)
• Be sure to connect the earth lead before connecting the amplifier.
• If you connect an optional power amplifier and do not use the
• Be sure to connect the earth lead before connecting the amplifier.
• If you connect an optional power amplifier and do not use the
built-in amplifier, the beep sound will be deactivated.
Tip (2-B-
)
For connecting two or more MD/CD changers, the source selector XA-
C30 (optional) is necessary.
C30 (optional) is necessary.
Connection diagram (
3
)
A
To AMP REMOTE IN of an optional power amplifier
This connection is only for amplifiers. Connecting any other
system may damage the unit.
This connection is only for amplifiers. Connecting any other
system may damage the unit.
B
To the interface cable of a car telephone
Warning
If you have a power aerial without a relay box, connecting this unit
with the supplied power connecting lead 7 may damage the aerial.
with the supplied power connecting lead 7 may damage the aerial.
Notes on the control leads
• The power aerial control lead (blue) supplies +12 V DC when you
• The power aerial control lead (blue) supplies +12 V DC when you
turn on the tuner, or when you activate the AF (Alternative
Frequency) or TA (Traffic Announcement) function.
Frequency) or TA (Traffic Announcement) function.
• When your car has built-in FM/MW/LW aerial in the rear/side glass,
connect the power aerial control lead (blue) or the accessory power
input lead (red) to the power terminal of the existing aerial
booster. For details, consult your dealer.
input lead (red) to the power terminal of the existing aerial
booster. For details, consult your dealer.
• A power aerial without a relay box cannot be used with this unit.
Memory hold connection
When the yellow power input lead is connected, power will always
be supplied to the memory circuit even when the ignition switch is
turned off.
When the yellow power input lead is connected, power will always
be supplied to the memory circuit even when the ignition switch is
turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
• Do not connect the speaker terminals to the car chassis, or connect
the terminals of the right speakers with those of the left speaker.
• Do not connect the earth lead of this unit to the negative (–)
terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active speakers (with
• Connect only passive speakers. Connecting active speakers (with
built-in amplifiers) to the speaker terminals may damage the unit.
• To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–) lead
for the right and left speakers.
for the right and left speakers.
• Do not connect the unit’s speaker leads to each other.
Note on connection
If speaker and amplifier are not connected correctly, “FAILURE”
appears in the display. In this case, make sure the speaker and
amplifier are connected correctly.
If speaker and amplifier are not connected correctly, “FAILURE”
appears in the display. In this case, make sure the speaker and
amplifier are connected correctly.
Click on the first or last page to see other MDX-F5800 service manuals if exist.