DOWNLOAD Sony MDX-F5800 Service Manual ↓ Size: 3.74 MB | Pages: 57 in PDF or view online for FREE

9

1

2

A

B

182 m

m

53 mm

4

2

3

1

1

c

4

6

6

c

c

c

1

• Choose the installation location carefully so that

the unit will not interfere with normal driving
operations.

• Avoid installing the unit in areas subject to dust,

dirt, excessive vibration, or high temperature,
such as in direct sunlight or near heater ducts.

• Use only the supplied mounting hardware for a

safe and secure installation.

Adjust the mounting angle to less than 45°.

4

Before installing the unit, remove the protection
collar 4 and the bracket 1 from the unit.

Remove the protection collar 4.
1 Engage the release keys 6 together with the

protection collar 4.

2 Pull out the release keys 6 to remove the

protection collar 4.

Remove the bracket 1.
1 Insert both release keys 6 together between

the unit and the bracket 1 until they click.

2 Pull down the bracket 1, then pull up the

unit to separate.

5

necessary (5-2).

collar 4 are properly engaged in the slots of the
unit (5-3).

6

6

Before detaching the front panel, be sure to press
(OFF). Press (OPEN), then slide the front panel to
the right side, and pull out the left side.

6

Place the hole A in the front panel onto the spindle
B

 on the unit as illustrated, then push the left side

in.

After turning off the ignition, be sure to press
and hold (OFF) on the unit until the display
disappears.
Otherwise, the display does not turn off and this
causes battery drain.

When the installation and connections are
completed, be sure to press the RESET button with
a ballpoint pen, etc., after detaching the front panel.

10

Auxiliary power connector may vary depending on
the car. Check your car’s auxiliary power connector
diagram to make sure the connections match
correctly. There are three basic types (illustrated
below). You may need to switch the positions of the
red and yellow leads in the car stereo’s power
connecting lead.
After matching the connections and switched
power supply leads correctly,  connect the unit to
the car’s power supply.  If you have any questions
and problems connecting your unit that are not
covered in this manual, please consult the car
dealer.

11

• This set can be disassembled in the order shown below.

FRONT PANEL ASSY

(Note 3)

3-8. LEVER (LE23) ASSY

(Page 15)

3-9. HOLDER ASSY

(Page 15)

3-10. CHUCKING ARM ASSY

(Page 16)

3-11. OPTICAL PICK-UP (KMS-242E)

(Page 16)

3-12. SL MOTOR ASSY (SLED) (M902),

SP MOTOR ASSY (SPINDLE) (M901)
(Page 17)

3-2. SUB PANEL ASSY

(Page 12)

3-3. MECHANISM DECK (MG-165A-138)

(Page 12)

3-4. MAIN BOARD

(Page 13)

3-5. SERVO BOARD

(Page 13)

3-6. MD COVER ASSY

(Page 14)

3-7. FLOAT BLOCK

(Page 14)

SET

Note 1: The process described in     can be performed in any order.

Note 2: Without completing the process described in     , the next process can not be performed.

Note 3: Illustration of disassembly is omitted.

12

 Follow the disassembly procedure in the numerical order given.

1

screw
(PTT2.6 

×

 6)

2

cover

3

two screws
(PTT2.6 

×

 6)

7

sub panel assy

4

two claws

4

two claws

6

flexible flat (14 core) cable
 (CN370)

5

1

screw
(PTT2.6 

×

 6)

5

mechanism deck
(MG-165A-138)

3

two screws
(PTT2.6 

×

 6)

4

bracket (MD)

2

connector
(CNP500)

1

screw
(PTT2.6 

×

 6)