Sony CDX-G1100U / CDX-G1100UE / CDX-G1101U / CDX-G1102U / CDX-G1150U / CDX-G1151U / CDX-G1152U / CDX-G1180UM Service Manual ▷ View online
CDX-G1100U/G1100UE/G1101U/G1102U/G1150U/G1151U/G1152U/G1180UM
5
1-4. Destination Code
Model
Destination OP5 OP4 OP3 OP2 OP1 OP0
CDX-G1100U
AEP, UK
0
0
1
0
0
1
Russian
8
0
1
0
0
1
CDX-G1100UE
Russian
8
0
1
0
0
7
CDX-G1101U
AEP, UK
0
0
1
0
0
1
CDX-G1102U
AEP, UK
0
0
1
0
0
1
CDX-G1150U
E, Mexican,
Korean
Korean
3
0
1
8
0
0
Saudi Arabia
2
0
1
8
0
4
Argentina
3
0
5
8
0
3
Indian
1
0
1
8
0
0
CDX-G1151U
E, Korean
3
0
1
8
0
0
Saudi Arabia
2
0
1
8
0
4
CDX-G1152U
Saudi Arabia
2
0
1
8
0
4
CDX-G1180UM
Indian
1
0
1
8
0
0
2. Confi rmation After Destination Setting
Execute the following operation after completing the destination
setting, and confi rm a correct destination was set.
Execute the following operation after completing the destination
setting, and confi rm a correct destination was set.
Destination setting checking method:
1. In the state of source off (the clock is displayed on the liquid
1. In the state of source off (the clock is displayed on the liquid
crystal display), enter the test mode by pressing the buttons in
order of the [SHUF 4] t [5] t [PAUSE 6] (press only the
order of the [SHUF 4] t [5] t [PAUSE 6] (press only the
[PAUSE 6] button for two seconds).
2. In the state in which the system controller version is displayed
on the liquid crystal display (refer to following fi gure), enter
the destination setting value display mode by pressing the [
the destination setting value display mode by pressing the [
SCRL DSPL] button twice.
(Displayed characters/values in the following fi gure are ex-
ample)
ample)
System controller version
SHUF
3. Confi rm the alphanumeric character of 12 digits in liquid crys-
tal display is a value correctly input.
(Displayed characters/values in the following fi gure are ex-
ample)
ample)
Destination code
12 digits
OP5 OP4 OP3 OP2 OP1 OP0
SHUF
4. The resetting operation is executed by pressing the [
OFF
SRC] button for 1 second after the confi rming ends, and the
unit returns to the normal condition.
unit returns to the normal condition.
MODEL IDENTIFICATION
Distinguish by Part No. on the bottom side of a main unit.
Distinguish by Part No. on the bottom side of a main unit.
– Bottom view –
(AEP, UK, E and Mexican models)
(AEP, UK, E and Mexican models)
– Bottom view –
(Russian, Saudi Arabia and Korean models)
(Russian, Saudi Arabia and Korean models)
– Bottom view –
(Argentina and Indian models)
(Argentina and Indian models)
Model Number Label
Part No.
Part No.
Model Number Label
Part No. (Saudi Arabia model)
Model Number Label
Part No.
(Russian and
Korean models)
(Russian and
Korean models)
Part No.
Model
4-543-144-0[]
CDX-G1100U: AEP and UK models (EUR)
4-543-145-0[]
CDX-G1101U: AEP and UK models (EUR)
4-543-146-0[]
CDX-G1102U: AEP and UK models (EUR)
4-543-147-0[]
CDX-G1100U: Russian model (RU2)
4-543-148-0[]
CDX-G1100UE: Russian model (RU2)
4-543-149-0[]
CDX-G1150U: E model (1E)
4-543-150-0[]
CDX-G1150U: Mexican model (MX3)
4-543-151-0[]
CDX-G1150U: Argentina model (AR)
4-543-152-0[]
CDX-G1150U: Indian model (IN)
4-543-153-0[]
CDX-G1180UM: Indian model (IN)
4-543-154-0[]
CDX-G1150U: Saudi Arabia model (EA)
4-543-155-0[]
CDX-G1150U: Korean model (KR)
4-543-156-0[]
CDX-G1151U: E model (1E)
4-543-157-0[]
CDX-G1151U: Saudi Arabia model (EA)
4-543-158-0[]
CDX-G1151U: Korean model (KR)
4-575-029-0[]
CDX-G1152U: Saudi Arabia model (EA)
Ver. 1.2
CDX-G1100U/G1100UE/G1101U/G1102U/G1150U/G1151U/G1152U/G1180UM
6
TEST DISCS
Use following TEST DISC (for CD) when this unit confi rms the
operation and checks it.
Use following TEST DISC (for CD) when this unit confi rms the
operation and checks it.
Part No.
Description
3-702-101-01 DISC
(YEDS-18),
TEST
4-225-203-01 DISC
(PATD-012),
TEST
NOTE OF PERFORMING THE OPERATION CHECK
When performing the operation check in the state that is removed
the CD mechanism deck from the main unit, it is necessary to use
a long fl exible fl at cable.
When performing the operation check, use following fl exible fl at
cable.
When performing the operation check in the state that is removed
the CD mechanism deck from the main unit, it is necessary to use
a long fl exible fl at cable.
When performing the operation check, use following fl exible fl at
cable.
Part No.
Description
1-846-819-31
CABLE FLEXIBLE FLAT (27 CORE)
(Length: 150 mm)
NOTE OF REPLACING THE KEY BOARD
When the KEY board is defective, replace the FRONT PANEL
OVERALL ASSY (Ref. No. FP1).
When the KEY board is defective, replace the FRONT PANEL
OVERALL ASSY (Ref. No. FP1).
NOTE OF REPLACING THE IC1301 ON THE MAIN BOARD
IC1301 on the MAIN board cannot replace with single. When this
part is damaged, replace the complete mounted board.
IC1301 on the MAIN board cannot replace with single. When this
part is damaged, replace the complete mounted board.
CLEANING THE CONNECTORS
The unit may not function properly if the
connectors between the unit and the front panel
are not clean. In order to prevent this, detach the
front panel (page 5) and clean the connectors with
a cotton swab. Do not apply too much force.
Otherwise, the connectors may be damaged.
connectors between the unit and the front panel
are not clean. In order to prevent this, detach the
front panel (page 5) and clean the connectors with
a cotton swab. Do not apply too much force.
Otherwise, the connectors may be damaged.
Notes
ˎ For safety, turn off the ignition before cleaning the
connectors, and remove the key from the ignition
switch.
switch.
ˎ Never touch the connectors directly with your fingers
or with any metal device.
and clean the connectors with
CDX-G1100U/G1100UE/G1101U/G1102U/G1150U/G1151U/G1152U/G1180UM
7
SECTION 2
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
(AEP and UK models)
Cautions
ˎ Run all ground (earth) leads to a common
ground (earth) point.
ˎ Do not get the leads trapped under a screw, or
caught in moving parts (e.g., seat railing).
ˎ Before making connections, turn the car ignition
off to avoid short circuits.
ˎ Connect the power supply lead ʘ to the unit and
speakers before connecting it to the auxiliary
power connector.
power connector.
ˎ Be sure to insulate any loose unconnected leads
with electrical tape for safety.
ˎ Choose the installation location carefully so that
the unit will not interfere with normal driving
operations.
operations.
ˎ Avoid installing the unit in areas subject to dust,
dirt, excessive vibration, or high temperature,
such as in direct sunlight or near heater ducts.
such as in direct sunlight or near heater ducts.
ˎ Use only the supplied mounting hardware for a
safe and secure installation.
Note on the power supply lead (yellow)
When connecting this unit in combination with other
stereo components, the amperage rating of the car
circuit to which the unit is connected must be higher
circuit to which the unit is connected must be higher
than the sum of each component’s fuse amperage
rating.
rating.
Mounting angle adjustment
Adjust the mounting angle to less than 45°.
Connection/Installation
Precautions
Connection
*1 Not supplied
*2 Speaker impedance: 4 – 8 Ω × 4
*3 RCA pin cord (not supplied)
*4 Depending on the type of car, use an adaptor for a
*2 Speaker impedance: 4 – 8 Ω × 4
*3 RCA pin cord (not supplied)
*4 Depending on the type of car, use an adaptor for a
wired remote control (not supplied).
*5 Depending on the type of car, use an adaptor (not
supplied) if the antenna connector does not fit.
*
2
from a wired remote control
(not supplied)*
(not supplied)*
4
For details, see “Making
connections” (page 16).
connections” (page 16).
*
3
*
3
Subwoofer*
1
Power amplifier*
1
from a car antenna (aerial)*
5
See “Power connection diagram” (page 16)
for details.
for details.
ʘ
If you have a power antenna (aerial) without a relay
box, connecting this unit with the supplied power
supply lead
box, connecting this unit with the supplied power
supply lead
ʘ may damage the antenna (aerial).
ɞ To the car’s speaker connector
ɟ To the car’s power connector
Making connections
1
Rear speaker
(right)
(right)
È Purple
2
¾ Purple/black
striped
3
Front speaker
(right)
(right)
È Gray
4
¾ Gray/black striped
5
Front speaker
(left)
(left)
È White
6
¾ White/black
striped
7
Rear speaker
(left)
(left)
È Green
8
¾ Green/black
striped
12
continuous power
supply
supply
Yellow
13
power antenna (aerial) /
power amplifier control
(REM OUT)
power amplifier control
(REM OUT)
Blue/white striped
15 switched power supply Red
16 ground (earth)
16 ground (earth)
Black
Memory hold connection
When the yellow power supply lead is connected,
power will always be supplied to the memory circuit
even when the ignition switch is turned off.
even when the ignition switch is turned off.
Speaker connection
ˎ Before connecting the speakers, turn the unit off.
ˎ Use speakers with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid damage.
avoid damage.
Subwoofer Easy Connection
You can use a subwoofer without a power amplifier
when it is connected to a rear speaker cord.
when it is connected to a rear speaker cord.
Notes
ˎ Preparation of the rear speaker cords is required.
ˎ Use a subwoofer with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid damage.
Front speaker
Subwoofer
CDX-G1100U/G1100UE/G1101U/G1102U/G1150U/G1151U/G1152U/G1180UM
8
2
Mount the unit onto the bracket
ʓ, then
attach the protection collar
ͨ.
Notes
ˎ If the catches are straight or bent outwards, the unit
will not be installed securely and may spring out.
ˎ Make sure the 4 catches on the protection collar ͨ
are properly engaged in the slots of the unit.
ʓ
182 mm (7
1
/
4
in)
53 mm (2
1
/
8
in)
Catch
ʓ
ͨ
ͩ
ͪ
Make sure your car’s auxiliary power connector, and
match the connections of cords correctly
depending on the car.
match the connections of cords correctly
depending on the car.
Common connection
When the positions of the red and yellow
leads are inverted
leads are inverted
When the car without ACC position
Power connection diagram
12
continuous power
supply
supply
Yellow
15 switched power supply Red
12 switched power supply Yellow
15
continuous power
supply
supply
Red
Auxiliary power connector
Red
Red
Yellow
Yellow
Red
Red
Yellow
Yellow
Red
Red
Yellow
Yellow
After matching the connections and switching
power supply leads correctly, connect the unit to
the car’s power supply. If you have any questions
and problems connecting your unit that are not
covered in this manual, consult the car dealer.
power supply leads correctly, connect the unit to
the car’s power supply. If you have any questions
and problems connecting your unit that are not
covered in this manual, consult the car dealer.
Installation
Before installing the unit, remove the protection
collar
collar
ͨ and the bracket ʓ from the unit.
1
Pinch both edges of the protection collar
ͨ, then pull it out.
ͨ, then pull it out.
2
Insert both release keys
ͧ until they
click, and pull down the bracket
ʓ, then
pull up the unit to separate.
Removing the protection collar and the
bracket
bracket
ͨ
ʓ
ͧ
Face the hook inwards.
Before installing, make sure the catches on both
sides of the bracket
sides of the bracket
ʓ are bent inwards 2 mm (
3
/
32
in).
1
Position the bracket
ʓ inside the
dashboard, then bend the claws outward
for a tight fit.
for a tight fit.
Mounting the unit in the dashboard
When replacing the fuse, be sure
to use one matching the
amperage rating stated on the
original fuse. If the fuse blows,
check the power connection and
replace the fuse. If the fuse blows
again after replacement, there
may be an internal malfunction. In such a case,
consult your nearest Sony dealer.
to use one matching the
amperage rating stated on the
original fuse. If the fuse blows,
check the power connection and
replace the fuse. If the fuse blows
again after replacement, there
may be an internal malfunction. In such a case,
consult your nearest Sony dealer.
Fuse replacement
Fuse (10 A)
Click on the first or last page to see other CDX-G1100U / CDX-G1100UE / CDX-G1101U / CDX-G1102U / CDX-G1150U / CDX-G1151U / CDX-G1152U / CDX-G1180UM service manuals if exist.