Sony CDX-848X Service Manual ▷ View online
CDX-848X
13
2-12. LSW BOARD, SPINDLE MOTOR (S) SUB ASSY (M102)
2-13. ELJ MOTOR ASSY (CHUCKING) (M103)
8
two precision screws
(P1.7
(P1.7
×
2.2)
7
3
spring (chucking)
6
retainer (disc)
4
precision screw
(P2
(P2
×
2.2)
5
bracket (CP)
9
Remove the spindle motor (S) sub assy (M102)
in the direction of the arrow.
in the direction of the arrow.
2
LSW board
1
precision screw
(P2
(P2
×
2.5)
2
two screws
(PTT2
(PTT2
×
4)
3
retainer (CHM)
4
ELJ motor
assy
(chucking)
(M103)
assy
(chucking)
(M103)
1
Remove two solders of
the chucking motor leads (M103).
the chucking motor leads (M103).
CDX-848X
14
• This set can be disassembled in the order shown below.
3-1.
ASSEMBLY FLOW
SECTION 3
MECHANISM DECK ASSEMBLY
3-2.
OPTICAL PICK-UP COMPLETE ASSY
chuck plate
1
Move the lever (LOCK 3A) in the direction of arrow
A
,
and return it a little in the direction of arrow
B
from the position where the chuck plate is moved
down to the lower limit.
down to the lower limit.
A
B
3
stop ring 2.0 (E type)
4
tension spring (DH)
2
optical pick-up complete assy
Note: Insert the shaft (A) first.
Note: Insert the shaft (A) first.
shaft (A)
3-2. OPTICAL PICK-UP
COMPLETE ASSY
(Page 14)
(Page 14)
3-3. GEAR (LOMINI)/
(LOAD CAM) ASSY
(Page 15)
(Page 15)
3-4. OPERATION CHECK
(Page 15)
CDX-848X
15
3-3.
GEAR (LOMINI)/(LOAD CAM) ASSY
gear (LOAD 2)
gear (LOMINI)
marking
Fig. A
Fig. A
chuck plate
2
Attach the gear (LOMINI) at the position
shown in Fig. A.
shown in Fig. A.
shaft (rotary prevention C)
1
Move the lever (LOCK 3A)
fully in the direction of arrow
fully in the direction of arrow
B
to move the chuck plate up.
B
4
stop ring 1.5 (E type)
3
Attach the gear (LOAD CAM) assy
with its facing inside.
with its facing inside.
slit
3-4.
OPERATION CHECK
1
Confirm that the slider moves in the direction of arrow
C
to move down
the chuck plate if the gear (LOAD CAM) is rotated in the direction of arrow
A
or the chuck plate moves up and the slider moves in the direction of
arrow
D
if the gear is rotated in the direction of arrow
B
.
chuck plate
slider
gear (LOAD CAM) assy
A
B
C
D
16
CDX-848X
SECTION 4
MECHANICAL ADJUSTMENT
• Elevator Height (Address) Adjustment
Note:
This adjustments is necessary when the system controller (IC201),
variable resistor (RV201), slider (R), slider (L), or chassis (ELV)
was replaced for any repair.
variable resistor (RV201), slider (R), slider (L), or chassis (ELV)
was replaced for any repair.
Connection:
Adjustment Method:
1. Connect this set to the master unit (e.g. MDX-C7970/C7970R),
1. Connect this set to the master unit (e.g. MDX-C7970/C7970R),
load a disc magazine, and place the set vertically as shown
below.
below.
2. Connect the regulated power supply to the master unit, and
turn the power on.
3. Press the DISC button on the master unit and select DISC 5.
4. At this time, if the elevator shaft does not position between
comb teeth A and B at addresses 5 and 6 as shown below,
adjust the following.
adjust the following.
5. Press repeatedly the DISC + and – buttons on the master unit
so that the elevator shafts moves from address 6 to address 5,
or from 5 to 6. At this time, adjust RV201 on the main board
so that the elevator shaft positions smoothly between comb
teeth A and B.
or from 5 to 6. At this time, adjust RV201 on the main board
so that the elevator shaft positions smoothly between comb
teeth A and B.
6. Further, place the set horizontally and make same adjustment
as mentioned above.
7. After adjustment at addresses 5 to 6 is finished, check all op-
erations from addresses 1 to 10 with the set placed vertically
and horizontally respectively to confirm that the elevator shaft
positions in a range between comb teeth A to B.
and horizontally respectively to confirm that the elevator shaft
positions in a range between comb teeth A to B.
GND
+
BUS cable
compact disc changer
master unit
CONTROL connector
(CN901)
(CN901)
power supply
(DC 14.4 V)
RV201
comb tooth at address 6
elevator shaft
comb tooth at address 6
comb tooth at address 5
OK
NG
elevator shaft
comb tooth at address 5
A
B
A
B
Click on the first or last page to see other CDX-848X service manuals if exist.