Sony STR-DA5800ES Service Manual ▷ View online
STR-DA5800ES
41
2-31. SB-SPTM BOARD
2
Remove the wire
from lead pin.
3
connector
(CN4611)
4
connector
(CN4601)
5
connector
(CN4606)
6
two screws
(BV/ring)
7
SB-SPTM board
:LUHVHWWLQJ
lead pin
slot
SB-SPTM board
SPTM board
SB-SPTM board
SPTM board
lead pin
Note 2: Wire should pass between SB-SPTM board and
SPTM
SPTM
board.
$(38.7:
86&1'
$(38.7:
1
Cut the cable tie.
Note 1: In reassembling, use new cable tie
to fasten the clamp same as before.
cable tie
2-32. SPTM BOARD
3
connector
(CX4103)
2
Remove the SPTM board
in the direction of an arrow.
1
two screws
(BV/ring)
5
connector
(CX4102)
4
connector
(CX4101)
6
SPTM board
• Abbreviation
CND : Canadian model
TW :
CND : Canadian model
TW :
Taiwan
model
Ver. 1.2
STR-DA5800ES
42
2-33. DC FAN (M2)
front side
:LUHsetting
–
5eDUsiGeYieZ–
3
screw
(BVTP3
u 8)
3
screw
(BVTP3
u 8)
5
screw
(BVTP3
u 8)
6
bracket (fan)
7
DC fan (M2)
DC fan (M2)
3
two screws
(BVTP3
u 8)
5
three screws
(BVTP3
u 8)
4
Remove the DC fan block
in the direction of an arrow.
1
Remove the wire
from the lead pin.
lead pin
heat sink
PROTECTOR_FH board
2
connector
(CN1951)
STR-DA5800ES
43
2-34. HEAT SINK BLOCK-1
< Fig. Q >
< Fig. O >
rear side
front side
front side
front side
Wire setting
cable tie
lead pin
lead pin
lead pin
lead pin
lead pin
heat sink
heat sink
Pass under the wire.
C2490
C2491
heat sink
1
Cut the cable tie. (See Fig. Q)
2
Remove the wire from lead pin.
(See Fig. Q)
2
Remove the wire from lead pin.
(See Fig. P)
2
Remove the wire from two lead pins.
(See Fig. O)
Note 2: The wire must not touch the heat sink.
< Fig. P >
Note 2: The wire must not touch
the heat sink.
Note 3: The wire must not touch C2490 and C2491.
Note 1: In reassembling, use new cable tie
to fasten the clamp same as before.
(AEP, UK, TW)
(US, CND)
(AEP, UK, TW)
1
Cut the cable tie.
(See Fig. P)
cable tie
• Abbreviation
CND : Canadian model
TW :
CND : Canadian model
TW :
Taiwan
model
Ver. 1.2
STR-DA5800ES
44
2-35. HEAT SINK BLOCK-2
< Fig. R >
< Fig. S >
rear side
rear side
Wire setting
lead pin
lead pin
7
Remove the wire from two lead pins.
(See Fig. S)
7
Remove the wire from lead pin.
(See Fig. R)
0
screw
(BVTP3
u 8)
0
three screws
(BVTP3
u 8)
0
two screws
(BVTP3
u 8)
qa
heat sink block
1
connector
(CN1201)
2
connector (CN1504)
5
connector (CN1505)
8
connector
(CN1399)
9
connector
(CN1405)
6
AMP_CONNECT-2 board
3
AMP_CONNECT-1 board
4
connector
(CN1202)
Note 1: The wire must not touch C2490 and C2491.
Note 2: The wire must not touch the heat sink.
C2490
C2491
Click on the first or last page to see other STR-DA5800ES service manuals if exist.