Sony STR-DA5800ES Service Manual ▷ View online
STR-DA5800ES
29
2-18. NETWORK BOARD BLOCK-1
3
connector
(See Fig. F, G)
4
connector
(CN1002)
5
connector
(CN605)
7
bracket (CTRL)
2
Remove the wire
from clamp (L35).
(See Fig. F)
1
Remove the wire
from lead pin.
(See Fig. G)
lead pin
lead pin
clamp (L35)
NETWORK board
NETWORK
board
board
CONTROL board
CONTROL board
heat sink
heat sink
NETWORK
board
board
heat sink
Rear side
Rear side
Rear side
:LUHsetting
Note: The wire must not touch heat sinks.
6
screw
(BVTP3
u 8)
6
screw
(BVTP3
u 8)
)ig)!
)ig*!
CONTROL board
$(38.7:
$(38.7:
$(38.7:
86&1'
• Abbreviation
CND : Canadian model
TW :
CND : Canadian model
TW :
Taiwan
model
Ver. 1.2
STR-DA5800ES
30
2-19. NETWORK BOARD BLOCK-2
NG
OK
(US, CND)
5
screw
(BVTP3
u 8)
5
screw
(BVTP3
u 8)
5
screw
(BVTP3
u 8)
4
screw
(P3
u 5)
Shield plate (NW) is seated between
NETWORK board and bracket (BR).
NETWORK board and bracket (BR).
Shield plate (NW) is not fixed between
NETWORK board and bracket (BR).
NETWORK board and bracket (BR).
shield plate
(NW)
(NW)
NETWORK board
bracket (BR)
2
screw
(BVTP3
u 8)
9
NETWORK board block
5
screw
(BVTP3
u 8)
6
clamp (L35)
5
four screws
(BVTP3
u 8)
8
reinforcement
(NW-S2)
7
reinforcement (NW-S1)
3
Lean the CONTROL board
in the direction of an arrow.
bracket (BR)
NETWORK board
shield plate
(NW)
(NW)
1
screw
(BVTT4
u 8)
(AEP, UK, TW)
(AEP, UK, TW)
Note: When installing the NETWORK board block, check that installed correctly.
• Abbreviation
CND : Canadian model
TW :
CND : Canadian model
TW :
Taiwan
model
Ver. 1.2
STR-DA5800ES
31
2-20. NETWORK BOARD
Note 1: When replacing the NETWORK board, refer to “NOTE
OF REPLACING THE NETWORK BOARD” (page 6).
1
connector
(CN3602)
3
Remove the DC fan 40 mm block
in the direction of an arrow.
4
DC fan 40 mm block
2
screw
(BVTP3
u 6)
2
screw
(BVTP3
u 6)
5
screw
(BVTP3
u 8)
6
shield plate (NW)
7
bracket (NW-R)
5
screw
(BVTP3
u 8)
Note 3: When installing the shield plate (NW), protruding
portion into the position of the above figure and
installed. The shield plate (NW) has specification
of the back and front. The contact surface with
NETWORK board into the shield side where
copper color side is reverse and installed.
– Shield side view –
– Copper color side view –
(NETWORK board is
a reverse side)
8
NETWORK board
DC fan 40 mm (M1)
protruding
portion
portion
holder (fan)
DC fan 40 mm (M1) setting
Note 2: Please check that there is no printed label.
(Printed label side is a bottom side)
(AEP, UK, TW)
• Abbreviation
TW :
TW :
Taiwan
model
Ver. 1.2
STR-DA5800ES
32
2-21. A-VIDEO BOARD
6
five screws
(BVTP3
u 8)
6
screw
(BVTP3
u 8)
8
two nylon rivets
(DIA.
3)
9
shield plate (VD-A)
6
screw
(BVTP3
u 8)
1
two screws
(BVTP3
u 8)
2
bracket
(BR)
block
block
3
connector
(CN6003)
5
connector
(CN6007)
4
connector
(CN6008)
7
Remove the A-VIDEO board block
in the direction of an arrow.
0
A-VIDEO
board
A-VIDEO board
lead pin
Note: When installing the shield plate (VD-A),
protruding portion into the position of
the left figure and installed.
The shield plate (NW) has specification
of the back and front.
The contact surface with NETWORK board
into the shield side where copper color side
is reverse and installed.
:LUHsetting
–
6KLHOGVLGHYLHZ–
–
&RSSHUFRORUVLGHYLHZ–
(
$9,'(2ERDUGLVDUHYHUVHVLGH)
protruding
portion
portion
$(38.7:
• Abbreviation
TW :
TW :
Taiwan
model
Ver. 1.2
Click on the first or last page to see other STR-DA5800ES service manuals if exist.