Sony STR-DA5800ES Service Manual ▷ View online
STR-DA5800ES
17
2-4. SUB D-VIDEO BOARD BLOCK-1
1
Cut the cable tie.
(See
Fig.
A)
1
Cut the cable tie.
(See
Fig.
A)
1
Cut the cable tie.
(See
Fig.
A)
cable tie
cable tie
3
HDMI cable (HDC2)
(CN3700)
(See
(See
Fig.
A)
HDMI cable (HDC2)
5
HDMI cable (HDC1)
(CN3701)
6
connector
(CN7511)
2
Remove wires from clamp (L35).
(See
Fig.
A)
clamp
(L35)
(L35)
heat sink
4
tape
(See Fig. B)
SUB D-VIDEO board
D-VIDEO board
Note 1: In reassembling, use new cable tie
to fasten the clamp same as before.
Note 3: The wire must not touch heat sinks.
Note 3: The wire must not touch heat sinks.
Note 3: The wire must not touch heat sinks.
Note 2: Stuff wires into the rear panel.
heat sink
heat sink
heat sink
heat sink
SUB D-VIDEO board
D-VIDEO
board
board
cable tie
Rear side
Rear side
wire (flat type) (19 core) (FFC1)
tape
SUB D-VIDEO board
< Fig. B >
< Fig. A >
Wire setting
(AEP, UK, TW)
(US, CND)
(US, CND)
(AEP, UK, TW)
(AEP, UK, TW)
30 mm
• Abbreviation
CND : Canadian model
TW :
CND : Canadian model
TW :
Taiwan
model
Ver. 1.2
STR-DA5800ES
18
2-5. SUB D-VIDEO BOARD BLOCK-2
4
screw
(BVTP3
u 8)
4
screw
(BVTP3
u 8)
5
SUB D-VIDEO board block
3
four screws
(B3
u 5)
1
Push two buttons of connector.
2
flexible flat cable
(CN7001)
2-6. SUB D-VIDEO BOARD
1
screw
(BVTP3
u 8)
1
screw
(BVTP3
u 8)
1
screw
(BVTP3
u 8)
2
clamp (L35)
4
bracket (S-HDMI)
5
SUB D-VIDEO board
3
bracket (S-HDMI2)
1
screw
(BVTP3
u 8)
2
clamp (L35)
(AEP, UK, TW)
(AEP, UK, TW)
Ver. 1.2
• Abbreviation
TW :
TW :
Taiwan
model
STR-DA5800ES
19
2-7. HAT BOARD
1
connector
(CN2941)
4
Remove the HAT board in
the direction of an arrow.
6
HAT board
2
screw
(BVTP3
u 8)
3
two nuts
(supplied with J861)
J861
5
wire (flat type) (19 core) (FFC1)
(CN807)
J861 is not
slanting.
slanting.
J861 is slanting.
OK
NG
colored line
colored line
Insert is straight to the interior.
Insert is incline
wire (flat type)
wire (flat type)
connector
connector
OK
NG
Note 1: When installing the wire (flat type), ensure the colored line.
No slanting after insertion.
Note 2: When installing the HAT
board, check that J861 is
installed
correctly.
STR-DA5800ES
20
2-8. USB-DDC BOARD (AEP, UK and Taiwan models)
1
two screws
(BVTP3
u 8)
3
Remove the USB-DDC
board block in the direction
of an arrow.
5
USB-CONNECT board
6
USB-DDC
board
2
connector
(CN102)
4
connector
(CN101)
(AEP, UK)
Note 1: When replacing the complete USB-DDC board, refer to “NOTE OF
REPLACING THE COMPLETE USB-DDC BOARD” (page 6).
Note 2: The USB-CONNECT board installed in AEP and UK models has
been deleted in the midway of production, and the D-AUDIO and
USB-DDC boards have been changed into connection with the wire
(AEP and UK models only). (Taiwan model does not use USB-
CONNECT board in the fi rst time of production, and the D-AUDIO
and USB-DDC boards are connection with the wire)
USB-DDC boards have been changed into connection with the wire
(AEP and UK models only). (Taiwan model does not use USB-
CONNECT board in the fi rst time of production, and the D-AUDIO
and USB-DDC boards are connection with the wire)
Ver. 1.2
Click on the first or last page to see other STR-DA5800ES service manuals if exist.