Sony STR-DA5800ES Service Manual ▷ View online
STR-DA5800ES
21
2-9. TUNER BLOCK
2-10. TUNER ASSY (TU1)
3
Remove the tuner block in
the direction of an arrow.
4
tuner block
colored line
colored line
Insert is straight to the interior.
Insert is incline
wire (flat type)
wire (flat type)
connector
connector
OK
NG
Note: When installing the wire (flat
type), ensure the colored line.
No slanting after insertion.
2
two screws
(BVTP3
u 8)
1
wire (flat type) (9 core)
(CN2692)
6
tuner assy
(TU1)
tuner assy
(TU1)
(TU1)
tuner assy
(TU1)
(TU1)
colored line
colored line
Insert is straight to the interior.
Insert is incline
wire (flat type)
wire (flat type)
connector
connector
OK
NG
Note: When installing the wire (flat
type), ensure the colored line.
No slanting after insertion.
2
wire (flat type) (9 core)
(FFC2)
wire (flat type) (9 core)
(FFC2)
(FFC2)
3
ferrite core
(FC1)
4
ferrite core (FC2)
ferrite core (FC1)
ferrite core (FC2)
1
saranet
cushion
(LXWXT)
(LXWXT)
saranet cushion
(LXWXT)
(LXWXT)
5
spacer
:LUHIODWW\SHFRUH))&VHWWLQJ
spacer
guide
line
line
guide line
6SDFHUVHWWLQJ
Ferrite core (FC2) has not
ridden on the connector.
ridden on the connector.
Ferrite core (FC2) has
ridden on the connector.
ridden on the connector.
)HUULWHFRUH)&VHWWLQJ
OK
NG
STR-DA5800ES
22
2-11. D-VIDEO BOARD BLOCK-1
1
connector
(CN3571)
6
connector
(CN3509)
(See Fig. C)
8
connector (CN3607)
(See Fig. C)
0
connector (CN3523)
(See Fig. D)
3
connector
(CN3511)
2
wire (flat type) (13 core)
(CN3510)
5
Remove wires
from lead pin.
(See Fig. C)
lead pin
SB-SPTM board
D-VIDEO board
D-VIDEO board
7
Remove the wire from clamp (L35).
(See Fig. C)
clamp (L35)
clamp (L35)
lead pin
SB-SPTM board
heat sink
Note 3: The wire must not touch heat sinks.
Note 3: The wire must not touch heat sinks.
Note 3: The wire must not touch heat sinks.
Rear side
Rear side
< Fig. C >
< Fig. D >
D-VIDEO board
heat sink
heat sink
Wire setting
colored line
colored line
Insert is straight to the interior.
Insert is incline
wire (flat type)
wire (flat type)
connector
connector
OK
NG
Note 2: When installing the wire (flat type), ensure the colored line.
No slanting after insertion.
Note 1: In reassembling, use new cable tie
to fasten the clamp same as before.
(AEP, UK, TW)
9
Cut the cable tie.
(See Fig. D)
4
Cut the cable tie.
(See Fig. C)
cable tie
cable tie
(US, CND)
(AEP, UK, TW)
• Abbreviation
CND : Canadian model
TW :
CND : Canadian model
TW :
Taiwan
model
Ver. 1.2
STR-DA5800ES
23
2-12. D-VIDEO BOARD BLOCK-2
1
seven screws
(B3
u 5)
2
screw
(BVTP3
u 8)
2
screw
(BVTP3
u 8)
2
screw
(BVTP3
u 8)
3
clamp (L35)
B
A
A
B
5
Push two buttons of connector.
4
Remove the D-VIDEO board block
in the direction of an arrow.
7
D-VIDEO board block
2
screw
(BVTP3
u 8)
6
flexible flat cable (FFC3)
(CN3101)
SUB D-VIDEO board
(CN7001)
(CN7001)
short side
long side
D-VIDEO board
(CN3101)
(CN3101)
Note: When installing the flexible flat cable (FFC3),
check a direction and install correctly.
2
screw
(BVTP3
u 8)
2
screw
(BVTP3
u 8)
(AEP, UK, TW)
• Abbreviation
TW :
TW :
Taiwan
model
Ver. 1.2
STR-DA5800ES
24
2-13. D-VIDEO BOARD
3
two screws
(BVTP3
u 8)
4
HDMI-7 bracket block
2
rainforcement
(HDMI)
6
heat sink (2011)
7
radiation sheet
3
screw
(BVTP3
u 8)
1
three screws
(BVTP3
u 8)
1
screw
(BVTP3
u 8)
8
D-VIDEO board
5
Bent claw is returned to
a straight form.
Note: When installing the heat sink (2011), check
that the radiation sheet has not shifted.
heat sink (2011) hole
heat sink (2011) hole
radiation sheet
radiation sheet
OK
IC3500
IC3500
NG
(AEP, UK, TW)
(AEP, UK, TW)
Ver. 1.2
• Abbreviation
TW :
TW :
Taiwan
model
Click on the first or last page to see other STR-DA5800ES service manuals if exist.